1996 TOYOTA RAV4 oil

Q06065
Q06076
D02315
OK if hot
Add if hot
D00699
D00700
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−181
1996 RAV4 (RM447U)
(d) Replace the ATF.
NOTICE:
Do not overfill.
(1) Using a 10 mm hexagon wrench, remove the drain
plug, gasket and drain the fluid.
(2) Install a new gasket and the drain plug securely.
(3) Add new fluid through the filler pipe.
Fluid type: ATF type T or equivalent
Drain and refill: 3.3 liters (3.5 US qts, 2.9 lmp. qts)
(4) Start the engine and shift the selector into all the
positions from P through L and then shift into the P
position.
(5) With the engine idling, check the fluid level. Add
fluid up to the COOL level on the dipstick.
(6) Check the fluid level with the normal fluid tempera-
ture 70 − 80°C (158 − 176°F) and add as neces-
sary.
NOTICE:
Do not overfill.
(e) Replace the transfer oil.
(1) Using a 10 mm hexagon wrench, remove the drain
plug and drain the oil.
(2) Install the drain plug.
(3) Add new oil through the filler pipe.
Recommended oil:
Oil grade API GL−5
Viscosity SAE 75W−90
Capacity: 0.7 liters (0.7 US qts, 0.6 lmp. qts)
(4) Check the oil level and add as necessary.
NOTICE:
Do not overfill.

D00697
Ok if hot
Add if hot
AT4252
0 − 1 mm
D02248
DI−182
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
1996 RAV4 (RM447U)
(f) Check the fluid leaks.
Check for leaks in the transmission and transfer.
If there are leaks, it is necessary to repair or replace O − rings,
FIPG’s, oil seals or other parts.
(g) Inspect and adjust the throttle cable.
(1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Loosen the adjustment nuts.
(4) Adjust the outer cable so that the distance between
the end of the boot and stopper on the cable is as
standard.
Standard boot and cable stopper distance:
0 − 1 mm (0 − 0.04 in.)
(5) Tighten the adjusting nuts.
(6) Recheck the adjustments.
(h) Adjust the shift control cable.
(1) Loosen the nut on the lever.
(2) Push the manual lever fully toward the right side of
the vehicle.

D02249
1
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−185
1996 RAV4 (RM447U)
CAUTION:
Perform the test at normal operating ATF temperature 50 − 80°C (122 − 176°F).
The line pressure test should always be carried out in parts. One should observe the conditions
of wheels or wheel stopper outside the vehicle while the other is performing the test.
(b) Measure the line pressure.
(1) Fully apply the parking brake and chock the 4 wheels.
(2) Start the engine and check idling speed.
(3) Step down strongly on the brake pedal with your left foot and shift into the D position.
(4) Measure the line pressure when the engine is idling speed.
(5) Press the accelerator pedal all the way down. Quickly read the highest line pressure when engine
speed reaches stall speed.
(6) Only when the shift solenoid valve ST is opened:
Apply battery positive voltage between terminal of the solenoid connector and body ground.
(7) In the same way, perform the test in the R position.
Automatic Transaxle Idling kPa (kgf/cm2, psi) Stall kPa (kgf/cm2, psi)
* D position (Shift solenoid valve ST open)530 − 706 (5.4 − 7.2, 76 − 102)1,324 − 1,549 (13.5 − 15.8, 192 − 225)
D position (Shift solenoid valve ST close)363 − 442 (3.7 − 4.3, 53 − 61)736 − 863 (7.5 − 8.8, 106 − 125)
R position530 − 706 (5.4 − 7.2, 76 − 102)1,324 − 1,549 (13.5 − 15.8, 192 − 225)
*: When battery voltage is supplied to terminal 4 of the solenoid connector and body ground, the shift sole-
noid valve ST valve is open.
If the measured pressures are not with in the specification, recheck the throttle cable adjustment and perform
a retest.
(8) Clear the DTC’s after the test.
Evaluation:
ProblemPossible cause
If the measured values at all positions are higher than speci-
fiedThrottle cable out of adjustment
Throttle valve defective
Regulator valve defective
If the measured value in all positions are lower than speci-
fied
Throttle cable out of adjustment
Throttle valve defective
Regulator valve defective
Oil pump defective
O/D direct clutch defective

D02250
2 − 3 m
(6.6 − 9.8 ft)
Battery
Adaptor SST 1
90980−10629 90980−111433
24 W
or
Q05128
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−187
1996 RAV4 (RM447U)
Clear the DTC’s after the test.
Evaluation:
ProblemPossible cause
If the measured values at all conditions are higher than the
specificationDifferential control valve defective
Solenoid modulator valve defective
If the measured values at all conditions are lower than the
specificationOil pump defective
Differential control valve defective
Solenoid modulator valve defective
If the pressure is low in the stall test
(Shift solenoid valve SLD ON only)Shift solenoid valve SLD defective
If the measured values are lower than the specification,
when sub−harness is connectedSolenoid modulator valve defective
Differential control valve defective
If the measured values are higher than the specification,
when sub−harness is connectedSolenoid modulator valve defective
Differential control valve defective
11. MANUAL SHIFTING TEST
HINT:
With this test, it can be determined whether the trouble is within
the electrical circuit or is a mechanical problem in the transaxle.
(a) Disconnect the solenoid wire.
(b) Inspect the manual driving operation.
Check that the shift and gear positions correspond with
the table below.

DI40X−02
DI−192
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
1996 RAV4 (RM447U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle Repair Matrix Chart
Chapter 3: Off−Vehicle Repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given in Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to continue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any of the other circuits, then
check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
No up−shift (A particular gear, from 1st to 3rd gear, is not up−
shifted)2. ECMDI−191
No up−shift (3rd → O/D)
1. O/D main switch & O/D OFF indicator light circuit
2. O/D cancel signal circuit
3. ECMDI−223
DI−221
DI−191
No down−shift (O/D → 3rd)
1. O/D main switch & O/D OFF indicator light circuit
2. O/D cancel signal circuit
3. ECMDI−223
DI−221
DI−191
No down−shift (A particular gear, from 1st to 3rd gear, is not
down−shifted)1. ECMDI−191
No lock−up1. Stop light switch circuit
2. ECMDI−227
DI−191
No lock−up off1. ECMDI−191
Shift point too high or too low1. Pattern select switch circuit
2. ECMDI−229
DI−191
Up−shifts to O/D from 3rd while O/D main switch is OFF1. O/D main switch & O/D OFF indicator light circuit
2. ECMDI−223
DI−191
Up−shifts to O/D from 3rd while engine is cold1. ECMDI−191
No kick−down1. ECMDI−191
Engine stalls when starting off or stopping1. ECMDI−191
”A/T OIL” indicator light does not light up or does not goes off1. A/T temperature switchDI−191
Chapter 2: On−Vehicle Repair
(: A540H Automatic Transaxle Repair Manual Pub. No. RM488U)
SymptomSuspect AreaSee page
Vehicle does not move in R position
1. 1−2 shift valve
2. 2−3 shift valve
3. Throttle valve
4. Off−vehicle repair matrix chart


−
Vehicle does not move in any forward position or reverse position
1. Manual valve
2. Primary regulator valve
3. Secondary regulator valve
4. Off−vehicle repair matrix chart


−

− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−193
1996 RAV4 (RM447U) No lock−up
1. Lock−up relay valve
2. Off−vehicle repair matrix chart
−
No lock− up OFF1. Lock−up relay valve
2. Off−vehicle repair matrix chart
−
No kick−down
1. Throttle cable
2. 1−2 shift valve
3. 2−3 shift valve
4. 3−4 shift valve
5. Down shift plug




No engine braking (1st (L position))
1. Low coast modulator valve
2. Low coast modulator valve
3. Off−vehicle repair matrix chart

−
No engine braking (2nd (2 position))
1. 2nd coast modulator valve
2. 2nd lock valve
3. Off−vehicle repair matrix chart

−
No up−shift (1st → 2nd)1. 1−2 shift valve
2. Off−vehicle repair matrix chart
−
No up−shift (2nd → 3rd)1. 2−3 shift valve
2. Off−vehicle repair matrix chart
−
No up−shift (3rd → O/D)1. 3−4 shift valve
2. Off−vehicle repair matrix chart
−
No down−shift (O/D → 3rd)1. 3−4 shift valve
2. Off−vehicle repair matrix chart
−
No down shift (3rd → 2nd)1. 2−3 shift valve
2. Off−vehicle repair matrix chart
−
No down shift (2nd → 1st)1. 1−2 shift valve
2. Off−vehicle repair matrix chart
−
Harsh engagement (N → R)1. No. 1 and No. 2 accumulator control valve
2. Off−vehicle repair matrix chart
−
Harsh engagement (N → D)1. C1 accumulator
2. Off−vehicle repair matrix chart
−
Harsh engagement (N → L)1. Low coast modulator valve
Harsh engagement (1st → 2nd (D position))1. B2 accumulator
2. Off−vehicle repair matrix chart
−
Harsh engagement (1st → 2nd (2 position))1. 2nd coast modulator valve
Harsh engagement (1st → 2nd → 3rd)1. Throttle modulator valve
2. No. 1 and No. 2 accumulator control valve

Harsh engagement (1st → 2nd → 3rd → O/D)1. No. 1 and No. 2 accumulator control valve
Harsh engagement (2nd → 3rd)1. C2 accumulator
Harsh engagement (3rd → O/D)1. B0 accumulator
2. Off−vehicle repair matrix chart
−
Harsh engagement (O/D → 3rd)1. C0 accumulator
2. B
0 accumulator


Harsh engagement (3rd → 2nd)
1. B2 accumulator
2. C
0 accumulator
3. B
0 accumulator
4. 2nd coast modulator valve
5. Off−vehicle repair matrix chart




−
Sliper shudder in forward and reverse (Directry after E/G start)
1. Pressure relief valve
2. Oil starter
3. Off−vehicle repair matrix chart
AX−8
−

DI−194
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
1996 RAV4 (RM447U) Front or rear wheel is slipping
1. Shift restrict reverse ball
2. Solenoid modulator valve
3. Differential control valve
4. Off−vehicle repair matrix chart


−
Shift point too high or too low1. Secondary regulator valve
Chapter 3: Off−Vehicle Repair
(: A540H Automatic Transaxle Repair Manual Pub. No. RM488U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position
1. Forward clutch (C1)
2. No. 2 one−way clutch (F
2)
3. 1st and reverse brake (B
3)
4. 2nd coast brake (B
1)
5. 2nd brake (B
2)
6. Direct clutch (C
2)






Vehicle does not move in reverse position
1. 2nd coast brake (B1)
2. Front planetary gear
3. Rear planetary gear
4. Direct clutch (C
2)
5. O/D direct clutch (C
0)
6. 1st and reverse brake (B
3)






Vehicle does not move in any forward position and reverse posi-
tion
1. Parking lock pawl
2. Oil pump
3. O/D one−way clutch (F
0)
4. O/D direct clutch (C
0)
5. O/D brake (B
0)
6. Front planetary gear
7. Rear planetary gear
8. O/D planetary gear








No lock−up1. Torque converter clutchAX−22
No lock−up OFF1. Torque converter clutchAX−22
Large shock during lock−up1. Torque converter clutchAX−22
E/G stalls when starting off and stopping1. Torque converter clutchAX−22
No up−shift (1st → 2nd)1. 2nd brake (B2)
2. No. 1 one−way clutch (F
1)


No up−shift (2nd → 3rd)1. Direct clutch (C2)
No up−shift (3rd → O/D)1. O/D brake (B0)
No down−shift (2nd → 1st)1. 2nd coast brake (B1)
Harsh engagement (N → R)1. Direct clutch (C2)
2. 1st and reverse brake (B
3)


Harsh engagement (N → D)1. Forward clutch (C1)
Harsh engagement (1st → 2nd (D position))1. 1st and reverse brake (B3)
Harsh engagement (2nd → 3rd)1. 2nd coast brake (B1)
Harsh engagement (3rd → O/D)
1. O/D direct clutch (C0)
2. O/D brake (B
0)
3. O/D planetary gear



Slip on shudder (Forward and reverse (After warm−up))
1. Torque converter clutch
2. Oil pump
3. No. 1 one−way clutch (F
1)
4. O/D direct clutch (C
0)
AX−22



Slip on shudder (Forward and reverse (Direct after E/G start))1. Torque converter clutchAX−22

− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−195
1996 RAV4 (RM447U) Slip on shudder (R range)
1. Direct clutch (C2)
2. O/D direct clutch (C
0)
3. O/D one−way clutch (F
0)



Slip on shudder (1st)1. Forward Clutch (C1)
2. No. 2 one−way Clutch (F
2)


Slip on shudder (2nd)1. 2nd brake (B2)
2. No. 1 one−way clutch (F
1)


Slip on shudder (2nd → 3rd (Up−shift))1. Direct clutch (C2)
Slip on shudder (3rd)1. Direct clutch (C2)
Slip on shudder (O/D)1. O/D brake (B0)
No engine braking (1st − 3rd)1. O/D direct clutch (C0)
No engine braking (1st (L position))1. 1st and reverse brake (B3)
No engine braking (2nd (2 position))2. 2nd coast brake (B1)
Poor acceleration (All positions)1. Torque converter clutch
2. Oil pumpAX−22

Poor acceleration (O/D)1. O/D direct clutch (C0)
2. O/D planetary gear

Poor acceleration (Other than O/D)1. O/D brake (B0)
2. O/D planetary gear

Poor acceleration (Other than 2nd)1. 2nd coast brake (B1)
2. 2nd brake (B
2)


Poor acceleration (1st and 2nd)1. O/D brake (B0)
Poor acceleration (1st and R position)1. 1st and reverse brake (B3)
Poor acceleration (R position)1. Forward clutch (C1)
Front or rear wheel is slipping1. Center differential clutch