1996 TOYOTA LAND CRUISER Vacuum

PP309−01
PP−12
−
PREPARATION SFI
1996 LAND CRUISER (RM451U)
RECOMMENDED TOOLS
09082−00040TOYOTA Electrical Tester.
09200−00010Engine Adjust Kit .
09258−00030Hose Plug Set .Plug for vacuum hose, fuel hose, etc.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Y0−06
−
SFI FUEL PRESSURE REGULATOR
SF−21
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT VACUUM SENSING HOSE FROM FUEL
PRESSURE REGULATOR
2. DISCONNECT FUEL RETURN HOSE FROM FUEL PRESSURE REGULATOR
CAUTION:
Put a shop towel under the pressure regulator.
3. REMOVE FUEL PRESSURE REGULATOR
(a) Loosen the lock nut, and remove the pressure regulator.
(b) Remove the O−ring from the pressure regulator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EN−01
SF−26
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT CRUISE CONTROL ACTUATOR CABLE
3. DISCONNECT ACCELERATOR CABLE
4. DISCONNECT THROTTLE CABLE
5. DISCONNECT NO.2 PCV HOSE
6. DISCONNECT AIR CLEANER HOSE
7. REMOVE EGR VACUUM MODULATOR AND VALVE (See page EC−10 )
8. REMOVE BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
9. DISCONNECT NO.1 PCV HOSE
10. DISCONNECT VACUUM SENSING HOSE
11. DISCONNECT NO.2 WATER BYPASS HOSE
12. DISCONNECT EVAP HOSE
13. DISCONNECT BRAKE BOOSTER HOSE
14. DISCONNECT THROTTLE POSITION SENSOR CON- NECTOR
15. DISCONNECT IDLE AIR CONTROL VALVE CONNEC-
TOR
16. DISCONNECT CONNECTOR FOR EMISSION CON- TROL VALVE SET ASSEMBLY
17. DISCONNECT EGR GAS TEMP. SENSOR CONNEC-
TOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI INJECTOR
SF−27
1996 LAND CRUISER (RM451U)
18. DISCONNECT PS RESERVOIR TANK
Remove the 3 bolts and disconnect the reservoir tank.
19. REMOVE ENGINE OIL DIPSTICK
20. DISCONNECT GROUND STRAP
21. REMOVE INTAKE MANIFOLD STAY
Remove the 2 bolts and intake manifold stay.
22. DISCONNECT VACUUM HOSES FROM TVV
23. DISCONNECT NO.1 WATER BYPASS HOSE FROM
CYLINDER HEAD
24. REMOVE AIR INTAKE CHAMBER
Remove the 6 bolts, 2 nuts, air intake chamber and 2 gaskets.
25. REMOVE FUEL RETURN PIPE
(a) Disconnect the fuel hose from the fuel pressure regulator.
(b) Remove the 2 bolts and fuel return pipe.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI INJECTOR
SF−33
1996 LAND CRUISER (RM451U)
(k) Connect the 6 injector connectors as shown.
2. INSTALL FUEL INLET PIPE
Install the fuel inlet pipe with 4 new gaskets, the 2 union bolts
and bolt.
Torque:
Union bolt: 29 N·m (300 kgf·cm, 22 ft·lbf)
Bolt: 20 N·m (200 kgf·cm, 14 ft·lbf)
3. INSTALL FUEL RETURN PIPE
(a) Install the fuel return pipe with the 2 bolts. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Connect the fuel hose to the fuel pressure regulator.
4. INSTALL AIR INTAKE CHAMBER
Install 2 new gaskets and the air intake chamber with the 6 bolts
and 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
5. CONNECT NO.1 WATER BYPASS HOSE TO CYL- INDER HEAD
6. CONNECT VACUUM HOSES TO TVV
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF−34
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
7. INSTALL INTAKE MANIFOLD STAY
Install the intake manifold stay with the 2 bolts.
Torque: 36 N·m (360 kgf·cm, 26 ft·lbf)
8. CONNECT GROUND STRAP
9. INSTALL ENGINE OIL DIPSTICK
10. CONNECT PS RESERVOIR TANK
Connect the reservoir tank with the 3 bolts. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
11. CONNECT EGR GAS TEMP. SENSOR CONNECTOR
12. CONNECT CONNECTOR FOR EMISSION CONTROL VALVE SET ASSEMBLY
13. CONNECT IDLE AIR CONTROL VALVE CONNECTOR
14. CONNECT THROTTLE POSITION SENSOR CONNEC- TOR
15. CONNECT BRAKE BOOSTER HOSE
16. CONNECT EVAP HOSE
17. CONNECT NO.2 WATER BYPASS HOSE
18. CONNECT VACUUM SENSING HOSE
19. CONNECT NO.1 PCV HOSE
20. INSTALL BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. INSTALL EGR VALVE AND VACUUM MODULATOR (See page EC−10 )
22. CONNECT THROTTLE CABLE
23. CONNECT ACCELERATOR CABLE
24. CONNECT CRUISE CONTROL ACTUATOR CABLE
25. CONNECT AIR CLEANER HOSE
26. CONNECT NO.2 PCV HOSE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EU−01
SF−42
−
SFI THROTTLE BODY
670
Author: Date:
1996 LAND CRUISER (RM451U)
THROTTLE BODY
ON−VEHICLE INSPECTION
1. INSPECT THROTTLE BODY
(a) Check that the throttle linkage moves smoothly.
(b) Check the vacuum at each port.
Start the engine.
Check the vacuum with your finger.
Port nameAt idleAt 3,500 rpm
PNo vacuumVacuum
ENo vacuumVacuum
RNo vacuumVacuum
2. INSPECT THROTTLE POSITION (TP) SENSOR
(a) Disconnect the TP sensor connector.
(b) Apply vacuum to the throttle opener.
(c) Using an ohmmeter, measure the resistance between
each terminal.
Throttle valve
conditionBetween terminalsResistance
Fully closedVTA − E20.2 − 5.7 kΩ
Fully closedIDL − E22.3 kΩ or less
OpenIDL − E2Infinity
Fully openVTA − E22.0 − 10.2 kΩ
−VC − E22.5 − 5.9 kΩ
(d) Reconnect the TP sensor connector.
3. INSPECT AND ADJUST DASHPOT
(a) Allow the engine to warm up to normal operating tempera-
ture.
(b) Check the idle speed.
Idle speed: 650 ± 50 rpm (N position)
(c) Open the throttle valve until the throttle lever separates from the dashpot end.
(d) Release the throttle valve gradually, and check the dash-
pot setting speed when the throttle lever touched the
dashpot end.
Dashpot setting speed: 2,200 ± 300 rpm
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SFI THROTTLE BODY
SF−43
671
Author: Date:
1996 LAND CRUISER (RM451U)
If not as specified, adjust using the following procedure:
(1) Stop the engine.
(2) Loosen the lock nut of the stopper bolt.
(3) Adjust the dashpot setting speed by turning thestopper bolt.
(4) Start the engine and check the dashpot setting speed.
(5) Retighten the lock nut.
(e) Maintain the engine at 3,500 rpm.
(f) Release the throttle valve, and check that the engine re- turns to idle in a few seconds.
4. CHECK THROTTLE OPENER
(a) Disconnect the vacuum hose from the throttle opener, and plug the hose end.
(b) Check the throttle opener setting speed. Throttle opener setting speed: 700 − 1,000 rpm
If the throttle opener setting is not as specified, replace the
throttle body.
(c) Stop the engine.
(d) Reconnect the vacuum hose to the throttle opener.
(e) Start the engine, and check that the idle speed returns to the correct speed.
Idle speed: 650 ± 50 rpm (N position)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010