1996 TOYOTA LAND CRUISER Ect

[x] Cancel search: Ect

odometer air filter clock reset wheel alignment fuel filter transmission fluid

Page 594 of 1399

TOYOTA LAND CRUISER 1996 J80 Workshop Manual Position
NORMALSHIFT SOLENOID NO. 1
MALFUNCTIONING
Solenoid valve
No. 1 No. 2GearSHIFT SOLENOID NO. 2
MALFUNCTIONING
BOTH SOLENOIDS MAL-
FUNCTIONINGSolenoid valve
No. 1 No. 2 GearSolenoid valve
No. 1

Position
NORMALSHIFT SOLENOID NO. 1
MALFUNCTIONING
Solenoid valve
No. 1 No. 2GearSHIFT SOLENOID NO. 2
MALFUNCTIONING
BOTH SOLENOIDS MAL-
FUNCTIONINGSolenoid valve
No. 1 No. 2 GearSolenoid valve
No. 1 No. 2 GearGear when shift selector is
manually operated
D
2
LON
ON
OFF
ON
ON
OFF
OFF OFF
ON
ON OFF
ON
ON
OFF
ON
ON ON OFF 1st
2nd
3rd
O/D
1st
2nd
3rd
1st
2nd X
X
X
X
X
X
X
X
X
ON
ON
OFF
OFF ON
ON
ON
3rd 3rd
O/D
3rd
3rd
1st
2nd X
X
X
X
X
X
X
X
XOFF
OFF
ON
ON OFF OFF
OFF
ON
ON
1st
O/D
3rd 1st O/D O/D
3rd
1st
1st
O/D O/D O/D
O/D
3rd 3rd
3rd
1st
1st
X: Malfunctions ON
ON
3rd
3rd
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−157
1996 LAND CRUISER (RM451U)
DTC P0753, P0758 Shift Solenoid A/B Electrical Malfunc-
tion (Shift Solenoid Valve No. 1/No. 2)
CIRCUIT DESCRIPTION
Shifting from 1st to O/D is done in combination with ON and OFF of the shift solenoid valves No. 1 and No\
.
2 controlled by ECM. If an open or short circuit occurs in either of the \
shift solenoid valves, the ECM controls
the remaining normal shift solenoid valve to allow the vehicle to be operat\
ed smoothly (Fail safe function).
Fail Safe Function:
If either of the shift solenoid valve circuits develops an open or short, \
the ECM turns the other shift solenoid
ON and OFF to shift to the gear positions shown in the table below. The ECM also turns the shift solenoid
valve SL OFF at the same time. If both solenoids are malfunction, hydraulic contr\
ol cannot be done electroni-
cally and must be done manually.
Manual shifting as shown in the following table must be done (In the case of a short circuit, the E\
CM stops
sending current to the short circuited solenoid).
HINT:
Check the shift solenoid valve No. 1 when DTC P0753 is output and check \
the shift solenoid valve No. 2
when DTC P0758 is output.
DTC No.DTC Detecting ConditionTrouble Area
P0753
P0758
The ECM checks for an open or short circuit in the shift sole-
noid valves No. 1 and No. 2 circuit when it changes
The ECM records DTC P0753 or P0758 if condition (a) or (b) is
detected once, but it does not light up MIL
After ECM detects condition (a) or (b) continuously 8 times or
more in one− trip, it causes the MIL light up until condition (a) or
(b) disappears
After that, if the ECM detects condition (a) or (b) once, it starts
lighting up MIL again
(a) Solenoid resistance is 8 Ω or less (short circuit) when the
solenoid is energized
(b) Solenoid resistance is 100 k Ω or more (open circuit) when
the solenoid is not energized
Open or short in shift solenoid valve No. 1/No. 2 circuit
Shift solenoid valve No. 1/No. 2
ECM
DI5KO−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010