1996 TOYOTA LAND CRUISER Engine oil

DI5KE−03
Vd762D00115
E4
11
12
13 1415
16
10 12
3
4
567
8
9
10
11
12
123
456
7
1
2
34
56
8910
11
7
8
9
12141516 13
17181920
21
22
23
242526
ECM T
erminals
1
23
4
5
6
7
89
10
11
13 12
15
16
171819202122 14
E5E6E7
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−145
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (T erminal No.)Wiring ColorConditionSTD Voltage (V)
SPD (E7−8) − E1 (E4− 24)L− W − BR− B
Disconnect cruise control connector and IG ON StationaryBelow 1.5
Disconnect cruise control connector and IG ON
Turn one rear wheel slowlyPulse signal is outputBelow 1.5 ↔ 4 − 6
S1 (E4− 10) − E1 (E4− 24)R − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ON9 − 14
1st or 2nd gear9 − 14
3rd or O/D gearBelow 1.5
S2 (E4− 9) − E1 (E4− 24)R−Y − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
2nd or 3rd gear9 − 14
1st or O/D gearBelow 1.5
SL (E4− 8) − E1 (E4− 24)R−L − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
Vehicle driving under lock −up position9 − 14
SP2+ (E6− 2) − SP− (E6− 8)V − V−G
IG OFF Disconnect ECM connector560 − 680 Ω
Engine is runningPulse signal is output
Below 1.5 ↔ 4 − 6
OD1 (E7− 18) − E1 (E4− 24)G−O − BR− BIG ON9 − 14
OD2 (E7− 19) − E1 (E4− 24)P−L − BR− BO/D main switch ON (O/D OFF)Below 3
O/D main switch OFF (O/D ON)9 − 14
OIL (E5− 12) − E2 (E5− 9)R−W − BR− BATF temperature: 110 °C (230° F)Below 1.5
L (E7−17) − E1 (E4− 24)G−W − BR− BIG ON Shift lever L position7.5 − 14
IG ON Shift lever other than L positionBelow 1.5
2 (E7−16) − E1 (E4− 24)O − BR− BIG ON Shift lever 2 position7.5 − 14
IG ON Shift lever other than 2 positionBelow 1.5
R (E7−15) − E1 (E4− 24)R−B − BR− BIG ON Shift lever R position7.5 − 14
IG ON Shift lever other than R positionBelow 1.5
NSW (E7−22) − E1 (E4− 24)B−W − BR− BIG ON Shift lever P or N positionBelow 3
IG ONShift lever other than P and N position9 − 14
STP (E7− 14) − E1 (E4− 24)G−W − BR− BIG ON Brake pedal is depressed7.5 − 14
IG ON Brake pedal is releasedBelow 1.5
THW (E5−4) − E2 (E5− 9)R−W − BR− BIG ON Engine coolant temperature 80 °C (176° F)Below 1.5
IDL (E5− 11) − E2 (E5− 9)G−W − BR− BIG ON Accel. pedal is releasedBelow 1.5
IG ONAccel. pedal is depressed9 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−151
1996 LAND CRUISER (RM451U)
Slip or shudder (Forward and reverse)
1. Throttle cable
2. Transmission control rod
3. Oil strainer
4. Pressure relief valve
5. Off
−vehicle repair matrix chartDI−131
DI−131

−
Slip or shudder (Particular position)
1. Throttle cable
2. Transmission control rod
3. Off −vehicle repair matrix chartDI−131
DI−131
−
No engine braking (1st (L position))1. Low coast modulator
2. Off −vehicle repair matrix chart
−
No engine braking (2nd (2 position))1. 2nd coast modulator
2. Off −vehicle repair matrix chart
−
No kick− down1. 1−2 shift valve
2. 2 −3 shift valve

Chapter 3: Off −Vehicle Repair
(  : A340F, A343F Automatic Transmission Repair Manual Pub. No. RM479U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion1. O/D one− way clutch (F0)
2. O/D planetary gear unit
3. Torque converter clutch

AT −26
Vehicle does not move in R position
1. 2nd coast brake (B1)
2. Front and rear planetary gear unit
3. Direct clutch (C
2)
4. 1st and reverse brake (B
3)




Vehicle does not move in D, 2 and L positions1. Forward clutch (C1)
Vehicle does not move in D and 2 positions1. No. 2 one− way clutch (F2)
Vehicle does not move in 2 position1. 1st and reverse brake (B3)
Vehicle does not move in L position
1. 2nd brake (B2)
2. 2nd coast brake (B
1)
3. Direct clutch (C
2)



No up− shift (1st → 2nd)1. 2nd brake (B2)
2. No. 1 one− way clutch (F
1)


No up−shift (2nd → 3rd)1. Direct clutch (C2)
No up−shift (3rd → O/D)1. O/D brake (B0)
No down−shift (2nd → 1st)1. 2nd brake (B2)
Lock−up does not engage or lock −up does not disengage1. Torque converter clutchAT −26
Harsh engagement (N → D)
1. Forward clutch (C1)
2. O/D one− way clutch (F
0)
3. No. 2 one− way clutch (F
2)



Harsh engagement (N → R)
1. Direct clutch (C2)
2. 1st and reverse brake (B
3)
3. O/D one− way clutch (F
0)



Harsh engagement (2nd → 3rd)1. Direct clutch (C2)
Harsh engagement (3rd → O/D)1. O/D brake (B0)
2. O/D planetary gear unit

Harsh engagement (O/D → 3rd)1. O/D one− way clutch (F0)
Harsh engagement (Lock −up)1. Torque converter clutchAT −26
Slip or shudder (Forward and reverse (After warm −up))
1. Torque converter clutch
2. O/D one− way clutch (F
0)
3. O/D direct clutch (C
0)
AT −26


Slip or shudder (Forward and reverse (Just after engine starts))1. Torque converter clutchAT −26
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q04346
ATF Temperature SensorOIL
E5
R−W
BR−B
1 2
E2
E5 ECM
12 9 4 −
6 V
DI−154
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P0710 Transmission Fluid Temperature Sensor Cir-
cuit Malfunction (ATF Temperature Sensor)
CIRCUIT DESCRIPTION
The ATF temperature sensor converts fluid temperature into resistance value w\
hich is input into the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0710
Either (a) or (b) is detected for 0.5 sec. or more
(a) Temp. sensor resistance is less than 79 Ω
(b) After the engine has been operating for 15 min. or more, the resistance at the temp. sensor is more than 156 k ΩOpen or short in ATF temp. sensor circuit
 ATF temp. sensor
 ECM
WIRING DIAGRAM
DI5KK−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM0KR−04
−
ENGINE MECHANICAL COMPRESSION
EM−3
506
Author: Date:
1996 LAND CRUISER (RM451U)
COMPRESSION
INSPECTION
HINT:
If there is lack of power, excessive oil consumption or poor fuel
economy, measure the compression pressure.
1. WARM UP AND STOP ENGINE
Allow the engine to warm up to normal operating temperature.
2. DISCONNECT DISTRIBUTOR CONNECTOR
3. REMOVE SPARK PLUGS (See page IG−1 )
4. CHECK CYLINDER COMPRESSION PRESSURE
(a) Insert a compression gauge into the spark plug hole.
(b) Fully open the throttle.
(c) While cranking the engine, measure the compression pressure.
HINT:
Always use a fully charged battery to obtain engine speed of
250 rpm or more.
(d) Repeat steps (a) through (c) for each cylinder.
NOTICE:
This measurement must be done in as short a time as pos-
sible. Compression pressure:
1,176 kPa (12.0 kgf/cm
2, 171 psi) or more
Minimum pressure: 883 kPa (9.0 kgf/cm
2, 128 psi)
Difference between each cylinder:
98 kPa (1.0 kgf/cm
2, 14 psi) or less
If the cylinder compression in one or more cylinders is low, pour
a small amount of engine oil into the cylinder through the spark
plug hole and repeat steps (a) through (c) for cylinders with low
compression.
If adding oil helps the compression, it is likely that
the piston rings and/or cylinder bore are worn or
damaged.
If pressure stays low, a valve may be sticking or
seating is improper, or there may be leakage past
the gasket.
5. REINSTALL SPARK PLUGS (See page IG−1 )
6. RECONNECT DISTRIBUTOR CONNECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E9−01
−
ENGINE MECHANICAL TIMING CHAIN
EM−13
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE OIL
2. DRAIN ENGINE COOLANT
3. REMOVE ENGINE UNDER COVER
4. REMOVE RADIATOR (See page CO−14 )
5. DISCONNECT A/C COMPRESSOR AND BRACKET
(a) Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.
(b) Remove the 4 mounting bolts, and disconnect the com- pressor from the bracket.
HINT:
Put aside the compressor, and suspend it.
(c) Remove the 5 bolts and A/C compressor bracket.
6. REMOVE RADIATOR PIPE
(a) Disconnect the No. 2 radiator hose from the water inlet.
(b) Remove the 2 nuts and radiator pipe.
7. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
8. REMOVE CYLINDER HEAD (See page EM−28 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−14
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
9. DISCONNECT OIL COOLER PIPE BRACKET FROM
NO. 1 OIL PAN
10. REMOVE OIL LEVEL SENSOR
(a) Remove the 4 bolts and level sensor.
(b) Remove the gasket from the level sensor.
11. REMOVE BOLTS HOLDING NO.1 OIL PAN TO TRANS-
MISSION HOUSING
Remove the 6 bolts.
12. REMOVE NO. 2 OIL PAN (See page LU−5)
13. REMOVE NO. 1 OIL PAN (See page LU−5)
14. REMOVE CRANKSHAFT PULLEY
(a) Using SST, remove the pulley bolt. SST 09213−58012, 09330 −00021
(b) Remove the crankshaft pulley.
HINT:
If necessary, remove the pulley with SST. SST 09950−50010 (09951 −05010, 09952−05010,
09953 −05010, 09953 −05020, 09954−05020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−15
1996 LAND CRUISER (RM451U)
15. CHECK THRUST CLEARANCE OF OIL PUMP DRIVE
SHAFT GEAR
Using a dial indicator with lever type attachment, measure the
thrust clearance.
Standard thrust clearance:
0.040 − 0.160 mm (0.0016 − 0.0063 in.)
Maximum thrust clearance: 0.30 mm (0.0118 in.)
If the thrust clearance is greater than maximum, replace the oil
pump drive shaft gear and/or timing chain cover.
16. REMOVE DRIVE BELT IDLER PULLEY
Remove the bolt and idler pulley.
17. REMOVE TIMING CHAIN COVER
(a) Remove the 9 mounting bolts, 2 mounting nuts and drive belt adjusting bar.
(b) Remove the oil pump by prying the portions between the cylinder block and oil pump with a screwdriver.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and oil pump.
(c) Remove the O−rings from the oil pump.
(d) Remove the gasket from the oil pump.
18. REMOVE TIMING CHAIN AND CAMSHAFT TIMING GEAR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−16
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
19. REMOVE CRANKSHAFT TIMING GEAR
HINT:
If necessary, remove the gear with SST.
SST 09950−40010 (09951 −04010, 09952−04010,
09953 −04020, 09954 −04010, 09955 −04060),
09950 −60010 (09951 −00350)
20. REMOVE CHAIN TENSIONER SLIPPER AND VIBRA- TION DAMPER
(a) Using a 10 mm hexagon wrench, remove the bolt and slip-
per.
(b) Remove the 2 bolts and damper.
21. REMOVE OIL JET
Remove the bolt and oil jet.
22. REMOVE CRANKSHAFT ROTOR
23. REMOVE OIL PUMP DRIVE SHAFT GEAR
24. REMOVE PUMP DRIVE SHAFT GEAR
If the pump drive shaft gear cannot be removed by hand, use
2 screwdrivers.
NOTICE:
Position shop rags as shown to prevent damage.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010