Page 182 of 1399
BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 184 of 1399
BE−40
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
23. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundConstantContinuity
4 − GroundDriver’s seat belt position UNFASTENContinuity
4 − GroundDriver’s seat belt position FASTENNo continuity
7 − GroundIgnition key SETContinuity
7 − GroundIgnition key RemoveNo continuity
8 − GroundDriver’s door position OPENContinuity
8 − GroundDriver’s door position CLOSENo continuity
5 − GroundIgnition switch position ONBattery positive voltage
5 − GroundIgnition switch position LOCK or ACCNo voltage
9 − GroundConstantBattery positive voltage
If circuit is as specified, try another relay.
If the circuit is not as specified, check the circuits connected to
other parts.
24. INSPECT ENGINE OIL LEVEL WARNING SWITCH
(a) Check that there is continuity between terminal with the
switch each position.
(b) Heat the switch to above 60° C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 185 of 1399
Z06300
BrightDark 2
3
Extinguished
1
−
BODY ELECTRICAL COMBINATION METER
BE−41
1996 LAND CRUISER (RM451U)
25. INSPECT ENGINE OIL LEVEL WARNING CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 − GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
26. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
27. INSPECT LIGHT CONTROL RHEOSTAT
(a) Connect terminals 1 and 3 through a 3.4 W test bulb.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2.
(c) Turn the rheostat knob to fully counterclockwise, and
check that the test bulb goes out.
(d) Gradually turn the rheostat knob to clockwise, and check
that the test bulb brightness changes from dark to bright.
If operation is not as specified, replace the rheostat.
HINT:
Adjust the brightness of illumination lights by rheostat.
A/C Control Assembly
Antenna Switch
Ash Receptacle
Audio
Center Diff. Lock Switch
Cigarette Lighter
Defogger Switch
Hazard Warning Switch
Shift Lever
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 308 of 1399
BO5152
BO391−01
BO−68
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SLIDING ROOF GLASS ALIGNMENT
(a) Start the engine and check the operation time of the slid-
ing roof.
Operation time: Approx. 5 sec.
(b) Check for abnormal noise or binding during operation.
(c) With the sliding roof fully closed, check for water leakage.
(d) Check for a difference in level between the sliding roof weatherstrip and roof panel.
Front End0.9 − 3.9 mm (0.035 − 0.154 in.)
Rear End0.9 − 3.9 mm (0.035 − 0.154 in.)
2. If the sliding roof does not operate:
ADJUST SLIDING ROOF GLASS ALIGNMENT
(a) Remove the control switch cover.
(b) Remove the large screw inside.
NOTICE:
Be careful not to lose the spring washer or shim.
(c) Manually operate the moon roof by inserting a special
crank−shaped screwdriver into the hole and turning the
drive shaft.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 339 of 1399
BR3295
Push RodStop Light Switch
Pedal Height
BR1CF−04
BR4980
A
BR0016
Pedal Freeplay
BR−6
−
BRAKE BRAKE PEDAL
988
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE PEDAL
ON−VEHICLE INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from dash panel:
167.5 − 177.5 mm (6.594 − 6.988 in.)
2. IF NECESSARY, ADJUST PEDAL HEIGHT
(a) Disconnect the connector from the stop light switch.
(b) Loosen the stop light switch lock nut and remove the stop
light switch.
(c) Loosen the push rod lock nut.
(d) Adjust the pedal height by turning the pedal push rod.
(e) Tighten the push rod lock nut. Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
(f) Install the stop light switch and turn it until it lightly con-
tacts the pedal stopper.
(g) Turn the stop light switch back one turn.
(h) Check the clearance (A) between the stop light switch and pedal.
Clearance: 0.5 − 2.4 mm (0.020 − 0.094 in.)
(i) Tighten the stop light switch lock nut.
(j) Connect the connector to the stop light switch.
(k) Check that the stop lights come on when the brake pedal
is depressed, and go off when the brake pedal is re-
leased.
(l) earance (A) between the stop light switch and the pedal
stopper has been adjusted correctly, the pedal freeplay
will meet the specifications.
3. CHECK PEDAL FREEPLAY
(a) Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.
(b) Push in the pedal by hand until the beginning of the se- cond resistance is felt. Measure the distance.
Pedal freeplay: 3 − 6 mm (0.12 − 0.24 in.)
HINT:
The freeplay to the 1st resistance is due to the play between the
clevis and pin. This is magnified up to 3 − 6 mm (0.12 − 0.24 in.)
at the pedal.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 340 of 1399
BR3297
Pedal Reserve Distancea
−
BRAKE BRAKE PEDAL
BR−7
989
Author: Date:
1996 LAND CRUISER (RM451U)
If incorrect, check the stop light switch clearance.
If the clearance is OK, then troubleshoot the brake system.
4. CHECK PEDAL RESERVE DISTANCE
Release the parking brake.
With the engine running, depress the pedal and measure
the pedal reserve distance, as shown.
Pedal reserve distance, ’a’, at 490 N (50 kgf, 110.2lbf):
More than 68 mm (2.68 in.)
If the reserve distance incorrect, troubleshoot the brake sys-
tem.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 348 of 1399
BR1CN-01
BR2238
-
BRAKE BRAKE BOOSTER ASSEMBLY
BR-15
1996 LAND CRUISER (RM451U)
BRAKE BOOSTER ASSEMBLY
OPERATION
1. OPERATING CHECK
(a) Depress the brake pedal several times with the engine off
and check that there is no change in the pedal reserve
distance.
(b) Depress the brake pedal and start the engine. If the pedal
goes down slightly, operation is normal.
2. AIR TIGHTNESS CHECK
(a) Start the engine and stop it after 1 or 2 minutes. Depress the brake pedal several times slowly. If the pedal goes
down furthest the 1st time, but gradually rises after the
2nd or 3rd time, the booster is air tight.
(b) Depress the brake pedal while the engine is running, and
stop the engine with the pedal depressed. If there is no
change in the pedal reserve travel after holding the pedal
for 30 seconds, the booster is air tight.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 350 of 1399
BR2237
BR1NM−01
BR2238
−
BRAKE BRAKE BOOSTER ASSEMBLY
BR−17
999
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE BOOSTER ASSEMBLY
OPERATION
1. OPERATING CHECK
(a) Depress the brake pedal several times with the engine off
and check that there is no change in the pedal reserve
distance.
(b) Depress the brake pedal and start the engine. If the pedal
goes down slightly, operation is normal.
2. AIR TIGHTNESS CHECK
(a) Start the engine and stop it after 1 or 2 minutes. Depress
the brake pedal several times slowly. If the pedal goes
down furthest the 1st time, but gradually rises after the
2nd or 3rd time, the booster is air tight.
(b) Depress the brake pedal while the engine is running, and
stop the engine with the pedal depressed. If there is no
change in the pedal reserve travel after holding the pedal
for 30 seconds, the booster is air tight.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
