1996 TOYOTA LAND CRUISER Fusible

BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation
Part Name
Symbol
Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKER FUSE
M−FUSE
H−FUSE
FL
CB
−
INTRODUCTION REPAIR INSTRUCTIONS
IN−5
5
Author: Date:
1996 LAND CRUISER (RM451U)
(3) Precoated parts are indicated in the component il-
lustrations by the ” ” symbol.
(g) When necessary, use a sealer on gaskets to prevent
leaks.
(h) Carefully observe all specifications for bolt tightening torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
(j) When replacing fuses, be sure the new fuse has the cor- rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
~
iJ<>~o~BE5594 IN0365
~
~
BE5595IN0366
~
~
BE5596IN0367
~
~
BE5597IN0367
~BE5598SN0368
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−34
−
INTRODUCTION TERMS
34
Author: Date:
1996 LAND CRUISER (RM451U)
CW
Curb W
eight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro−Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR−VMExhaust Gas Recirculation −Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E−VRVElectric V acuum Regulating V alve
EXHExhaust
FEFuel Economy
FFFront−Engine Front− Wheel−Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront−Engine Rear− Wheel−Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront−Wheel−Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH0EO−02
CH0712
BlueRed
White
Charging
Necessary
OK
Add Distilled
Water
CH−2
−
CHARGING CHARGING SYSTEM
1996 LAND CRUISER (RM451U)
CHARGING SYSTEM
ON−VEHICLE INSPECTION
1. CHECK BATTERY ELECTROLYTE LEVEL AND VOLT-
AGE
(a) Check the electrolyte quantity of each cell.
If under the lower level, replace the battery (or add distilled wa-
ter if possible). check the charging system.
(b) Measure the battery voltage between the negative ( −)
and positive (+) terminals of the battery.
Standard voltage: At 20° C (68°F): 12.7 − 12.9 V
HINT:
Before measuring the voltage, turn the ignition switch
OFF and turn off the electrical systems (headlight, blower
motor, rear defogger etc.).
If the vehicle has been running, wait 20 minutes or more
after the vehicle stops before measuring the battery volt-
age.
If the voltage is less than specification, charge the battery.
HINT:
Check the indicator as shown in the illustration.
2. CHECK BATTERY TERMINALS, FUSIBLE LINK AND FUSES
(a) Check that the battery terminals are not loose or cor-
roded.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03788
CORRECT WRONG
Clearance
Z00038
Nippondenso Borroughs
−
CHARGING CHARGING SYSTEM
CH−3
1996 LAND CRUISER (RM451U)
(b) Check the fusible link and fuses for continuity.
Fusible link
MAIN 2.0 A
AM1 1.25 B
AM2 0.3 P
H−fuseAM1 50 A
FuseIGN 7.5 A
GAUGE 15 A
3. INSPECT DRIVE BELTS
(a) Visually check the drive belt for cracks, oiliness or wear.
Check that the belt does not touch the bottom of the pulley
groove.
If necessary, replace the drive belts as a set.
(b) Using a belt tension gauge, measure the belt tension. Belt tension gauge:
Nippondenso BTG−20 (95506 −00020)
Borroughts No. BT−33−73F
Drive belt tension:
New belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
Used belt200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
If the belt tension is not as specified, adjust it.
HINT:
”New belt” refers to a belt which has been used less than
5 minutes on a running engine.
”Used belt” refers to a belt which has been used on a run-
ning engine for 5 minutes or more.
After installing a new belt, run the engine for about 5 min-
utes and recheck the belt tension.
4. VISUALLY CHECK GENERATOR WIRING AND LIS- TEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.
5. INSPECT DISCHARGE WARNING LIGHT CIRCUIT
(a) Turn the ignition switch ”ON”. Check that the discharge warning light comes on.
(b) Start the engine. Check that the light goes off.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22419
WR−Y
GECM
Y−R R
R
BR
Battery Fusible Link
EFI
R/B No.2
EFI Main
Relay
Y−R
FL MAIN
BR
1
Mass Air Flow
Meter
2
2 2
2 2
2
1 1
1
F8 2
4
3 E7
E5
E5 VGMRLY
2
23
7
5 16B+
E1
EB
E21
EB1 EA2
−
DIAGNOSTICS ENGINE
DI−21
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22424
Fusible Link
Battery
FL AM2
F7
EA2
6
11
3
1 IG Switch
W−RW
−R
B−R B−R
IH1
14B−R
B−R
B−R
B−R
B−R B−R 2
2
2
2
2
2 1
1
1
1
1
1 W−L
W−R
W−G Y
Y−R
Y−L
BR
BR E4
E4
E4
E4
E4 E4
E4
E4 11 12
25 2
1
15
13
26
EC
Injector #10
#20 #30
#40
#50
#60
E01
E02 ECM
No.1
No.2
No.3
No.4
No.5
No.6
FI6588 FI6538
A00064
10V/
Division
GND 10V/
Division
100 m sec./Division (Idling) GND(Magnification)
1 m sec./Division (Idling)
Injection duration
−
DIAGNOSTICS ENGINE
DI−55
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Reference INSPECTION USING OSCILLOSCOPE
INJECTOR SIGNAL WAVEFORM
With the engine idling, measure between terminals #10 − #60 and E01 of ECM.
HINT:
The correct waveform is as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22475
BatteryFusible
Link
FL AM2
F7W−R
EA2
W−R
B−R B−R
EA2
B−R
B−W B−W
W−B
Distributor
Ignition
Coil 4
12
EA2
IH1
W−B
8 1
2
Noise
Filter 45
B 3
Igniter Tr2
2
1
IH2 IH2
B−G
B−G
B−Y B−YE4
E4 IGT
IGF Tr15V
ECM
1 3 11
6
IG Switch
1
EC
17 23
14 13
−
DIAGNOSTICS ENGINE
DI−97
1996 LAND CRUISER (RM451U)
DTC P1300 Igniter Circuit Malfunction
CIRCUIT DESCRIPTION
The ECM determines the ignition timing, turns on Tr1 at a predetermined angle ( °CA) before the desired
ignition timing and outputs and ignition signal (IGT) ”1” to the\
igniter.
Since the width of the IGT signal is constant, the dwell angle control circuit in \
the igniter determines the time
the control circuit starts primary current flow to the ignition coil based \
on the engine rpm and ignition timing
one revolution ago, that is, the time the Tr2 turns on.
When it reaches the ignition timing, the ECM turns Tr1 off and outputs the IGT signal ”O”.
This turns Tr2 off, interrupting the primary current flow and generating a high voltage i\
n the secondary coil
which causes the spark plug to spark. Also, by the counter electromotive forc\
e generated when the primary
current is interrupted, the igniter sends an ignition confirmation signal (IGF)\
to the ECM. The ECM stops fuel
injection as a fail safe function when the IGF signal is not input to the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P1300No IGF signal to ECM for 6 consecutive IGT signals during
engine running Open or short in IGF or IGT circuit from igniter to ECM
 Igniter
 ECM
WIRING DIAGRAM
DI5PQ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22477
BatteryFusible Link
E8
1 W
2 2
EFI
R/B No.2
R−YR−Y
EA2E7ECM
BATT
2
FL MAIN
2
−
DIAGNOSTICS ENGINE
DI−105
1996 LAND CRUISER (RM451U)
DTC P1600 ECM BATT Malfunction
CIRCUIT DESCRIPTION
Battery positive voltage is supplied to terminal BATT of the ECM even when the ignition switch is OFF for
use by the DTC memory and air −fuel ratio adaptive control value memory, etc.
DTC No.DTC Detecting ConditionTrouble Area
P1600Open in back up power source circuitOpen in back up power source circuit
 ECM
HINT:
If DTC P1600 appear, the ECM does not store another DTC.
WIRING DIAGRAM
DI5PT−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010