1996 TOYOTA LAND CRUISER Position

BE−6
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Engine oil level warning light does not light up.
1. Bulb
2. Meter Circuit
3. Engine Oil Level Warning Switch
4. Wire Harness−
BE−32
BE−34 −
Low oil pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−32
BE−34 −
Fuel level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−34
BE−32 −
INDICATOR LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
High beam indicator light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness−
BE−19
BE−32 −
Shift indicator lights do not light up. (ALL)
1. Shift Position Indicator Wiring Circuit
2. Park/Neutral Position Switch
3. Wire Harness
4. Bulb−
BE−34 AT −6
−
Shift indicator lights do not light up. (L, 2, D)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Park/Neutral Position Switch
4. Light Control Rheostat
5. Wire Harness−
BE−34 AT −6
BE−34 −
Shift indicator lights do not light up. (PWR)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Pattern Select Switch
4. Wire Harness−
BE−34 AT −6
−
Shift indicator lights do not light up. (2nd START)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. ECM
4. Wire Harness−
AT −6
−
−
Only one shift indicator does not light up.1. Bulb
2. Shift Position Indicator Wiring Circuit−
BE−34
Indicator lights do not light up. (Except Turn, Hi −beam)1. GAUGE Fuse (I/P F/B)
2. Wire Harness−
−
O/D OFF indicator light does not light up.
1. Bulb
2. O/D Main Switch
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Wire Harness−
−
−
Cruise control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LW−01
−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE−11
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK−No continuity
ACC7 − 9Continuity
ON3 − 4, 6 − 7 − 9Continuity
START2 − 3 − 4
6 − 9 − 10Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SWITCH CONTINUITY
ConditionTester connectionSpecified condition
SW OFF
(Key removed)−No continuity
SW ON (Key set)1 − 5Continuity
If continuity is not as specified, replace the switch.
3. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE−21 )
4. INSPECT SEAT BELT WARNING RELAY CIRCUIT
(See page BE−34 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LZ−01
BE−14
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
TAILA2 − A11Continuity
HEADA2 − A11 − A13Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
FlashA9 − A12 − A14Continuity
Low beamA3 − A9Continuity
High beamA9 − A12Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.3 − 4Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.2 − 3Continuity
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M4−01
BE1428
ON
OFF
−
BODY ELECTRICAL INTERIOR LIGHT SYSTEM
BE−21
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT GLOVE BOX LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Closed)−No continuity
ON (Opened)1 − 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT DOOR COURTESY SWITCH CONTINUITY
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin released:
opened door).
(b) Check that there is no continuity between terminal and the switch body with the switch OFF (switch pin pushed
in: closed door).
If operation is not as specified, replace the switch.
3. INSPECT FRONT PERSONAL LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
ON5 − 6Continuity
If continuity is not as specified, replace the personal light.
4. INSPECT ROOM LIGHT ASSEMBLY
(a) Disconnect the connector from room light assembly.
(b) Turn the room light switch ON, check that there is continu-
ity between terminal 2 and body ground.
(c) Turn the room light switch DOOR, and check that there is continuity between terminal 1 and 2.
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M6−01
−
BODY ELECTRICAL BACK−UP LIGHT SYSTEM
BE−23
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT PARK/NEUTRAL POSITION SWITCH CONTINUITY (See page AT−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M8−01
−
BODY ELECTRICAL STOP LIGHT SYSTEM
BE−25
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT STOP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SW pin free1 − 2Continuity
SW pin pushed in−No continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MA−01
B7B16
B18
B7 B4
B18 B16
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
BE−27
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT FRONT WIPER AND WASHER SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
Wiper OFFB4 − B7Continuity
Wiper INTB4 − B7Continuity
Wiper LOB7 − B18Continuity
Wiper HIB13 − B18Continuity
Washer OFF−No continuity
Washer ONB8 − B16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT REAR WIPER AND WASHER SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
Washer ONB2 − B16Continuity
Wiper OFF−No continuity
Wiper INTB10 − B16Continuity
Wiper ONB1 − B16Continuity
Washer ONB1 − B2 − B16Continuity
If continuity is not as specified, replace the switch.
3. INSPECT INTERMITTENT WIPER OPERATION
(a) Turn the wiper switch to INT position.
(b) Turn the intermitte nt time control switch to FAST position.
(c) Connect the positive (+) lead from the battery to terminal
B18 and the negative ( −) lead to terminal B16.
(d) Connect the positive (+) lead from the voltmeter to termi- nal B7 and the negative ( −) lead to terminal B16, and
check that the meter needle indicates battery positive
voltage.
(e) After connecting terminal B4 to termianl B18, connect B18 to terminal B16.
Then, check that the voltage rises from O volt to battery
positive voltage within time as follows.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
BE−29
1996 LAND CRUISER (RM451U)
7. INSPECT REAR WIPER RELAY INTERMITTENT OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 4.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 3 and the negative ( −) lead to terminal 4.
(c) After disconnecting the positive (+) lead from terminal 2,
connect it to terminal 1, and then, check that the meter
needle rises from O V to battery positive voltage within 6
to 10 seconds.
If operation is not as specified, replace the relay.
8. Low Speed: INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
negative ( −) lead to terminal 1, and check that the motor oper-
ates at low speed.
If operation is not as specified, replace the motor.
9. High Speed:
INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (− ) lead to terminal 1, and check that the motor op-
erates at high speed.
If operation is not as specified, replace the motor.
10. Stopping at Stop Position: INSPECT FRONT WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 3.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010