1996 TOYOTA LAND CRUISER Diff lock

RS0OZ−02
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
RS−1
1100
Author: Date:
1996 LAND CRUISER (RM451U)
SRS AIRBAG
PRECAUTION
NOTICE:
The LAND CRUISER is equipped with an SRS , which comprises a driver airbag \
and a front pas-
senger airbag. Failure to carry out service operations in the correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serio\
us accident. Further,
if a mistake is made in servicing the SRS, it is possible the SRS may fail to\
operate when re-
quired. Before performing servicing (including removal or installation \
of parts, inspection or
replacement), be sure to read the following items carefully, then follow the correct procedure
described in the repair manual.
Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the mos\
t impor-
tant source of information when troubleshooting. When troubleshooting th\
e SRS, always in-
spect the DTCs before disconnecting the battery.
Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front
passenger airbag assembly, and airbag sensor assembly should be inspected (See pages
RS−9 , RS−23 and RS−34 )
Never use SRS parts from another vehicle. When replacing parts, replace them with \
new parts.
Never disassemble and repair the steering wheel pad, front passenger airbag assembly , or air-
bag sensor assembly in order to reuse it.
If the steering wheel pad, front passenger airbag assembly or airbag sen\
sor assembly have
been dropped, or if there are cracks, dents or other defects in the case, br\
acket or connector,
replace them with new ones.
Use a volt/ohmmeter wi th high impedance (10 k Ω/V minimum) for troubleshooting the system’s
electrical circuits.
Information labels are attached to the periphery of the SRS components. Follow the instruc-
tions on the notices.
After work on the SRS is completed, check the SRS warning light (See pa\
ge DI−240).
If the vehicle is equipped with a mobile communication system, refer to the precaution in the
IN section.
CAUTION:
Work must be started after 90 seconds from the time the ignition switch is t\
urned to the ”LOCK”
position and the negative ( −) terminal cable is disconnected from the battery.
(The SRS is equipped with a back− up power source so that if work is started within 90 seconds
of disconnecting the negative ( −) terminal cable of the battery, the SRS may be deployed.)
When the negative (−) terminal cable is disconnected from the battery, the memory of the clock
and audio system will be canceled. So before starting work, make a record o\
f the contents mem-
orized in the audio memory system. When work is finished, reset the audio syst\
ems as they
were before and adjust the clock. To avoid erasing the memory of each memory system, never
use a back−up power supply from outside the vehicle.
Before repairs, remove the airbag sensor if shocks are likely to be applied to the senso\
r during
repairs.
Do not expose the steering wheel pad, front passenger airbag assembly, or airbag sensor as-
sembly directly to hot air or flames.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1U7−01
−
SUSPENSION AND AXLE TROUBLESHOOTING
SA−1
858
Author: Date:
1996 LAND CRUISER (RM451U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers \
indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
(w/ Differential locking system):
Check that center differential lock mode is set.
When switching differential Free↔Lock, the indicator lamp will blink if the gears of the differen-
tial lock sleeve are not meshed. If this occurs, when the tires are rotated \
to apply differential
power to the differential, the differential locks and the indicator lamp\
light up.
SymptomSuspect AreaSee page
Wander/ pulls
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Steering linkage: loosen or worn
4. Hub bearings: loosen or worn
5. Steering gear: out of adjustment or brokenSA−3
SA−4
SR−47 SA−8
SR−41
Bottoming
1. Vehicle: overloaded
2. Spring weak
3. Shock absorber: worn out−
SA−49
SA−49
Sways/ pitches
1. Tires: worn or improperly inflated
2. Stabilizer bar: bent or broken
3. Shock absorber: worn outSA−3
SA−60
SA−49
Front wheel shimmy
1. Tires: worn or improperly inflated
2. Wheels: out of balance
3. Shock absorber: worn out
4. Wheel alignmemt: incorrect
5. Hub bearings: loosen or worn
6. Steering linkage: loosen or worn
7. Steering gear: out of adjustment or brokenSA−3
SA−3
SA−49 SA−3
SA−7
SR−45
SR−38
Abnormal tire wear
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Suspension parts: worn out
4. Shock absorber: worn outSA−3
SA−3 −
SA−49
Noise in front dif ferential
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Side bearing: worn
6. Differential bearing: loosen or wornSA−21
SA−29
SA−29
SA−29
SA−29
SA−29
Oil leak from front dif ferential
1. Oil level: too high or wrong grade
2. Drive pinion oil seal: worn or damaged
3. Side gear oil seal: worn or damaged
4. Companion flange: loosen or damaged
5. Side gear shaft: damagedSA−21
SA−29
SA−29
SA−29
SA−29
Noise in rear axle
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Axle shaft bearing: worn
6. Differential bearing: loosen or wornSA−73
SA−87
SA−87
SA−87
SA−87
SA−87
Oil leak from rear axle1. Oil seal: worn or damaged
2. Rear axle housing: crackedSA−73
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA−2
−
SUSPENSION AND AXLE TROUBLESHOOTING
859
Author: Date:
1996 LAND CRUISER (RM451U)
Oil leak from rear dif
ferential
1. Oil level: too high or wrong grade
2. Oil seal: worn or damaged
3. Companion flange: loosen or damagedSA−73
SA−73
SA−87
Indicator lights do not light up
1. Fusible link: blown
2. GAUGE fuse: blown
3. Bulb: burned out
4. Wiring or ground: faultyBE−9
BE−9
BE−32 −
Indicator lights do not light up
(Diff. lock control switch RR or FR RR position)
1. DIFF fuse: blown
2. Diff. lock control switch: faulty
3. Diff. lock ECU: faulty
4. Wiring or ground: faultyBE−9
SA−101
SA−101 −
Differential lock does not operate
1. Diff. lock position switch: faulty
2. Diff. lock actuator: faulty
3. Diff. lock ECU: faulty
4. Differential carrier (Diff. lock): faulty
5. Wiring or ground: faultySA−101
SA−101
SA−101
SA−101−
After differential lock, lock not release
When vehicle speed is higher than approx. 8 km/h (5mph)1. Speed sensor: faulty
2. Diff. lock ECU: faulty
3. Wiring or ground: faultyBE−32
SA−101 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1960
SST
RA1072
Filler Hole
Oil
0 − 5 mm (0 − 0.20 in.)
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−23
1996 LAND CRUISER (RM451U)
(c) Apply light coat of gear oil on threads of a new companion
flange nut.
(d) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 196 N·m (2,000 kgf·cm, 145 ft·lbf)
14. ADJUST DRIVE PINION PRELOAD (See page SA−36 )
15. STAKE DRIVE PINION NUT
16. INSTALL FRONT PROPELLER SHAFT (See page PR−5 )
17. FILL DIFFERENTIAL WITH GEAR OIL Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
w/o Differential lock:
2.80 liters (2.9 US qts, 2.5 Imp. qts)
w/ Differential lock:
2.65 liters (2.8 US qts, 2.3 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00530
w/o Differential LockSide Gear Thrust WasherPinion Gear
Pinion Gear Thrust Washer
 Dust Deflector
Front Bearing Outer Race
 Oil Seal
Companion Flange
Bearing Cap
Differential Carrier

Adjusting Nut Lock Oil Slinger
Differential Case
Drive Pinion
Ring Gear
Side Baring
Straight Pin
Adjusting Nut
 Bearing Spacer


Oil Storage Ring
Outer Race
Outer Race
 Non− reusable part 
Lock Plate
x 10
x 5 Pinion Shaft
Pinion Gear
Pinion Washer
Rear Bearing
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−25
882
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00531
w/ Differential LockSide Gear
Thrust Washer
Pinion Gear
Thrust Washer
Outer Race

Oil Seal Companion Flange
Bearing Cap
Differential Carrier
 Adjusting Nut Lock Oil Slinger
Drive Pinion
Ring Gear
Side Baring
Adjusting Nut

Bearing Spacer

Oil Storage Ring
Outer Race
 Non− reusable part

Lock Plate x 8
x 4 
O− Ring
Pinion Washer
Rear Bearing

 Dust Deflector
Front Bearing Outer Race
Adjusting Nut
Sleeve
Spider Side GearLH Differential Case
RH Differential Case
x 8
 Precoated part 
Gasket Indicator Switch
Actuator

Straight Screw Plug
Spring Seat
Compression Spring
Ball

Shaft Retainer Shift Fork Shaft Shift Fork

Slotted Spring Pin
Pinion Gear
SA−26
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
883
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UM−03
FA2038
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−27
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ DIFFERENTIAL LOCK:
BEFORE REMOVAL, SHIFT FRONT DIFFERENTIAL
TO LOCK
(a) Turn the ignition switch to the ON position.
(b) Keep the center differential lock condition.
(c) Turn the differential lock control switch to the FR/RR posi-
tion and lock the front differential.
(d) Rotating the tires, check they are in the differential lock condition.
(e) Disconnect the cable from the negative terminal of the battery.
2. DRAIN DIFFERENTIAL OIL
3. REMOVE FRONT AXLE SHAFTS (See page SA−13)
4. REMOVE TIE ROD FROM KNUCKLE ARM (See page SA−13 )
5. REMOVE FRONT PROPELLER SHAFT (See page PR−3 )
6. w/ DIFFERENTIAL LOCK: DISCONNECT CONNECTORS AND TUBE
HINT:
When connecting the tube of the harness side to the hose
of the actuator side, its depth of insertion is 15 mm (0.59
in.).
Take care that water or equivalent does not adhere to the
connector and hose.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z10092
w/o Differential Lock
w/ Differential Lock
SA−28
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
7. REMOVE DIFFERENTIAL CARRIER ASSEMBLY
(a) Remove the 10 nuts, washers and differential carrier as-
sembly.
NOTICE:
Be careful not to damage the installation surface. Torque: 27 N·m (280 kgf·cm, 20 ft·lbf)
(b) Remove the gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010