1996 TOYOTA LAND CRUISER Oil engine

CO114−02
CO−6
−
COOLING WATER PUMP
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WATER PUMP
Install a new gasket and the water pump with the 4 bolts and 2
nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
2. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Install fan to the fluid coupling.
(b) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(c) Temporarily install the fan pulley mounting nuts.
(d) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(e) Connect the oil cooler hose to the clamp on the fan
shroud.
(f) Install the drive belts with the adjusting bolt and pivot bolt.
(g) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(h) Adjust the drive belts (See page CH−2 ).
3. CONNECT NO.3 WATER BYPASS HOSE
4. CONNECT RADIATOR INLET HOSE
5. FILL RADIATOR WITH ENGINE COOLANT
6. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO117−02
CO−14
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE BATTERY AND BATTERY TRAY
(a) Disconnect the battery cables.
(b) Remove the nuts, hold −down clamp and battery.
(c) Remove the bolt and disconnect the ground strap.
(d) Remove the 5 bolts and battery tray.
3. REMOVE RADIATOR GRILLE
Remove the 5 screws, clip and radiator grille.
4. DISCONNECT NO.3 WATER BYPASS HOSE
5. DISCONNECT RADIATOR INLET HOSE
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. REMOVE RADIATOR
(a) Stretch the belts and loosen the water pump pulley mounting nuts.
(b) Loosen the lock, pivot and adjusting bolts of the genera- tor, and remove the drive belts.
(c) Disconnect the oil cooler hose from the clamp on the fan shroud.
(d) Remove the 2 bolts holding the fan shroud to the radiator.
(e) Remove the 4 water pump pulley mounting nuts.
(f) Pull out the fan with fluid coupling, water pump pulley and
fan shroud.
8. DISCONNECT A/T OIL COOLER HOSES
9. DISCONNECT RADIATOR OUTLET HOSE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04771
InsideOutside
DI−8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting\
should be performed in the
order for all possible circuits to be considered as the causes of the problem\
s. In many cases, by carrying
out the basic engine check shown in the following flow chart, the location \
causing the problem can be found
quickly and efficiently. Therefore, use of this check is essential in engine troubleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.
YES
2 Is engine cranked?
NO Proceed to page ST−16 , and continue to trouble-
shoot.
YES
3 Does engine start?
NO Go to step 7.
YES
4 Check air filter.
PREPARATION:
Remove air filter.
CHECK:
Visually check that the air cleaner element is not dirty or exces-
sive oily.
HINT:
If necessary, clean the element with compressed air. First blow
from inside thoroughly, then blow from outside of element.
NG Repair or replace
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00164P03792
P22893
DI−56
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check spark plug and spark of misfiring cylinder.
PREPARATION:
(a) Remove No.2 and No.3 cylinder head cover.
(b) Disconnect the high −tension cord from spark plug.
(c) Remove spark plug.
CHECK:
(a) Check the carbon deposits on electrode.
(b) Check electrode gap.
OK:
(1) No large carbon deposit present.
Not wet with gasoline or oil.
(2) Electrode gap: 0.8 mm (0.031 in.).
PREPARATION:
(a) Install the spark plug to the high −tension cord.
(b) Ground the spark plug.
(c) Disconnect injector connector.
CHECK:
Check if spark occurs while engine is being cranked.
NOTICE:
To prevent excess fuel being injected from the injectors
during this test, don’t crank the engine for more than 5 − 10
seconds at a time.
OK:
Spark jumps across electrode gap.
NG Replace or check ignition system (See page IG−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S06273
E1
1
G−
2
BR
L
L G1
NE2
NE2−
12
E6
3
2
Distributor
Crankshaft Position Sensor G2
ECM
NE
4
1 L
L
G W
R
E6
E6
E6
E6
E6 11
10 4
56
DI−62
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0335 Crankshaft Position Sensor ”A” Circuit Malfunction
CIRCUIT DESCRIPTION
The crankshaft position sensor (NE signal) consists of a signal plate and pick up coil. The NE\
signal plate
has 24 teeth and is built into the distributor. When the camshaft rotates, the protrusion on the signal plate
and the air gap on the pick up coil change, causing fluctuations in the magnetic field and generating an elec-
tromotive force in the pick up coil. The NE signal sensor generates 24 signals fo\
r every engine revolution.
The ECM detects the standard crankshaft angle based on the G1, G2 signals, \
detects the actual crankshaft
angle and the engine speed by the NE signals, and detects misfire by NE2 sign\
als.
DTC No.DTC Detecting ConditionTrouble Area
P0335
No crankshaft position sensor signal (NE signal) to ECM dur-
ing cranking.
(2 trip detection logic) Open or short in crankshaft position sensor circuit for NE
signal.
 Crankshaft position sensor for NE signal
 Starter
 ECM
No crankshaft position sensor signal (NE signal) to ECM with
engine speed 550 rpm or more (2 trip detection logic)
WIRING DIAGRAM
DI5PH−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24663
2(−)
3
4 1
(+)
−
DIAGNOSTICS ENGINE
DI−65
1996 LAND CRUISER (RM451U)
DTC P0340 Camshaft Position Sensor Circuit
Malfunction
CIRCUIT DESCRIPTION
The camshaft position sensors (G1 and G2 signals) consist of a signal pla\
te and a pick up coil. The G1, G2,
signal plates each have one tooth on the outer circumference and are built int\
o the distributor. When the
camshaft rotates, the protrusion on the signal plate and the air gap on the pick \
up coil change, causing fluc-
tuations in the magnetic field and generating an electromotive force in the pick \
up coil. The ECM detects the
standard crankshaft angle based on the G1, G2 signals, detects the actual cranks\
haft angle and engine
speed by the NE signals, and detects misfire by NE2 signals.
DTC No.DTC Detecting ConditionTrouble Area
P0340No camshaft position sensor signal (G signal) to ECM with
engine speed 550 rpm or more. Open or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
WIRING DIAGRAM
Refer to DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction) o\
n page DI−62 for the WIRING
DIAGRAM.
INSPECTION PROCEDURE
1 Check resistance of camshaft position sensor.
PREPARATION:
Disconnect camshaft position sensor connector.
CHECK:
Measure resistance between terminals 2, 3 and 4 of distributor
connector.
OK:
Resistance
Cold185 − 275 Ω
Hot240 − 325 Ω
”Cold” is from − 10°C (14°F) to 50°C (122°F) of engine coolant
temperature and "Hot" is from 50°C (122°F) to 100°C (212°\
F).
Reference: INSPECTION USING OSCILLOSCOPE
Refer to page DI−62 for Reference INSPECTION USING OS-
CILLOSCOPE.
NG Replace distributor housing assembly.
OK
DI5PI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00167P22894
P24664
−
DIAGNOSTICS ENGINE
DI−67
1996 LAND CRUISER (RM451U)
DTC P0385 Crankshaft Position Sensor ”B” Circuit
Malfunction
CIRCUIT DESCRIPTION
The crankshaft position sensor (NE2 signal) consists of a signal plate and a pick up coil. The NE2 signal plate
has 34 teeth and is mounted on the crankshaft. When the crankshaft rotates, the protrusion on the signal
plate and the air gap on the pick up coil change, causing fluctuations i\
n the magnetic field and generating
an electromotive force in the pick up coil. The NE2 signal sensor generate\
s 34 signals for every engine revo-
lution. The ECM detects the standard crankshaft angle based on G1, G2 signals d\
etects the actual crank-
shaft angle and the engine speed by NE signals, and detects misfire by NE2 si\
gnals.
DTC No.DTC Detecting ConditionTrouble Area
P0385
No crankshaft position sensor signal (NE 2 signal) to ECM
during cranking. (2 trip detection logic) Open or short in crankshaft position sensor for NE2 signals.
 Crankshaft position sensor for NE2 signal.
 ECM
No crankshaft position sensor signal (NE 2 signal) to ECM with
engine speed 550 rpm or more. (2trip detection logic)
WIRING DIAGRAM
Refer to DTC 0335 (Crankshaft Position Sensor ”A” Circuit Malfunction)\
on page DI−62 for WIRING DIA-
GRAM.
INSPECTION PROCEDURE
1 Check resistance of crankshaft position sensor for NE2 signal.
PREPARATION:
Disconnect crankshaft position sensor connector.
CHECK:
Measure resistance between terminals 1 and 2 of crankshaft
position sensor connector.
OK:
Resistance
Cold1630 − 2740 Ω
Hot2065 − 3225 Ω
”Cold” is from − 10°C (14°F) to 50°C (122°F) of engine coolant
temperature and "Hot" is from 50°C (122°F) to 100°C (212°F).
Reference: INSPECTION USING OSCILLOSCOPE
Refer to page DI−62 for Reference INSPECTION USING OS-
CILLOSCOPE.
NG Replace crankshaft position sensor.
OK
DI5PJ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010