1996 TOYOTA LAND CRUISER engine

A00192
ONFC
(+)
(−)
BE6653
P24684
DI−11 8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal FC of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal FC of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 5.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Connect the TOYOTA hand−held tester and check operation of fuel pump relay.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Start the engine.
(c) Turn TOYOTA hand−held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester.
CHECK:
Check operation of fuel pump relay when it is switched ON and OFF by the\
TOYOTA hand −held tester.
OK:
Operating noise can be heard from the relay.
OK Go to step 8.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00193
Continuity ContinuityOpen
Open (+) (−) 1
2
3
4
5
6
1
2
3
6
54
P24685
P24686
P24687
FPR
(+)
(−)
−
DIAGNOSTICS ENGINE
DI−11 9
1996 LAND CRUISER (RM451U)
5 Check operation of fuel pump relay.
PREPARATION:
(a) Disconnect fuel pump relay connector.
(b) Remove fuel pump relay.
CHECK:
Check continuity between terminals of fuel pump relay.
OK:
Terminals 3 and 5Continuity
Terminals 2 and 5Open
Terminals 1 and 5Continuity
(Reference value 80 Ω)
CHECK:
(a) Apply battery voltage between terminals 1 and 5.
(b) Measure voltage between terminals 1 and 2.
OK:
Terminals 1 and 2Battery voltage
NG Replace fuel pump relay.
OK
6 Check voltage between terminal FPR of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Start the engine.
CHECK:
Measure voltage between terminal FPR of ECM and body
ground while racing the engine.
OK:
Time after engine startedVoltage
60 seconds or more0 − 3 V
Less than 60 seconds9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00194
HighLowFPR
P22900
P09401
DI−120
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
7 Check for open and short in harness and connector between terminal FPR of
ECM connector and fuel pump relay (See page IN−28).
NG Repair or replace harness or connector.
OK
8 Check operation of fuel pump.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Connect the TOYOTA hand − held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
CHECK:
Check operation of fuel pump, when it is operated by the TOYO-
TA hand− held tester and terminal FPR of ECM is grounded and
is not grounded.
OK:
There is pressure in the inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
FPR is grounded
(Low speed)FPR is not grounded (High speed)
NGNGGo to step 9
NGOKGo to step 10
OKNG
Repair or replace
harness or connector between fuel pump
relay and fuel pump.
9 Check fuel pump (See page SF−6 ).
NG Repair or replace fuel pump.
OK
Check for open or short in harness and connector between EFI main relay (Mark\
ing: EFI) and cir-
cuit opening relay and fuel pump relay and fuel pump and body ground (See p\
age IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00195
ONFC
BE6653
P22178
P09401
−
DIAGNOSTICS ENGINE
DI−121
1996 LAND CRUISER (RM451U)
10 Check fuel pump resistor. (See page SF−58).
NG Replace fuel pump resistor.
OK
Check for open and short in harness and connector between fuel pump relay and fuel\
pump resis-
tor and fuel pump (See page IN−28).
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check fuel pump operation.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
(a) Connect between terminal FC of ECM and body ground.
(b) Check for fuel pressure in the fuel inlet hose when it is pinched off.
OK:
There is pressure in the fuel inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
OK Go to step 4.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−122
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check circuit opening relay (See page DI−84 ).
NG Replace circuit opening relay.
OK
3 Check voltage between terminal FC of ECM connector and body ground (See\
step 3 of TOYOTA hand −held tester).
OK Go to step 4.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Check operation of fuel pump relay (See step 5 of TOYOTA hand −held tester).
NG Replace fuel pump relay.
OK
5 Check voltage between terminal FPR of ECM connector and body ground (Se\
e step 6 of TOYOTA hand −held tester).
NG Check and replace ECM (See page IN−28 ).
6 Check for open and short in harness and connector between terminal FC of\
ECM
connector and fuel pump relay (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00196
ONFC
High LowFPR
BE6653
P22901
P09401
−
DIAGNOSTICS ENGINE
DI−123
1996 LAND CRUISER (RM451U)
7 Check operation of fuel pump.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
(a) Connect terminal FC of ECM and body ground.
(b) Check operation of fuel pump when terminal FPR of ECM
is grounded and is not grounded.
OK:
There is pressure in the inlet hose.
HINT:
At this time, you will hear a fuel flowing noise.
FPR is grounded
(Low speed)FPR is not grounded (High speed)
NGNGGo to step 8
NGOKGo to step 9
OKNG
Repair or replace
harness or connecter between fuel pump
relay and fuel pump.
8 Check fuel pump (See page SF−6 ).
NG Repair or replace fuel pump.
OK
Check for open or short in harness and connector between EFI main relay (Mark\
ing: EFI) and cir-
cuit opening relay and fuel pump relay and fuel pump and body ground (See p\
age IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−124
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
9 Check fuel pump resistor (See page SF−58 ).
NG Replace fuel pump resistor.
OK
Check for open and short in harness and connector between fuel pump relay and fuel\
pump resis-
tor and fuel pump (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22216
Pressure RegulatorVSV
ECM
To Fuel Tank
(Return)
From Delivery Pipe Intake
Manifold
P22482
BRFrom BatteryR/B No.2EB
2
2
2
2
EFI Main
22Y−R
Y−R
EB11
REA27R
R−Y
EZ1
VSV for Fuel21
EZ1
Relay
EFI
12 4
3
1B B3
L−R
Pressure Control E7
E4 3
21 FPU
MRLY
ECM
B+
E01
−
DIAGNOSTICS ENGINE
DI−125
1996 LAND CRUISER (RM451U)
Fuel Pressure Control Circuit
CIRCUIT DESCRIPTION
The ECM turns on a VSV (V acuum Switching Valve) to draw the
air into the diaphragm chamber of the pressure regulator if it de-
tects that the temperature of the engine coolant is too high dur-
ing engine starting.
The air drawn into the chamber increases the fuel pressure to
prevent fuel vapor lock at high engine temperature in order to
help the engine start when it is warm.
Fuel pressure control ends approx. 120 sec. after the engine is
started.
WIRING DIAGRAM
DI5PZ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010