1996 TOYOTA LAND CRUISER light

AC2SM−01
AC2717
Connector ”A”
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC−69
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT ILLUMINATION OPERATION
Connect the positive (+) lead from the battery to terminal A −13
and the negative ( −) lead to terminal A−3, then check that the
illuminations light up.
If illuminations do not light up, test the bulb.
2. Air Inlet Control Switch:
INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal
A−9 and the negative ( −) lead to terminal A−8.
(b) With the air inlet control button pushed in, check that the FRESH or RECIRC indicator light lights up.
(c) Next, push in the button again, and check that the indica-
tor light goes off and the other indicator light lights up.
AICSwitch
.-20-2-CN06571 .-18-2-B
ModeControlSwitch
2=i=~~~:=i~;=j::;5-H--+__Blower Speed
ControlSwitch
TemperatureControl
Switch Connector
"A"
~~.~r-r""""~~~9&ru7 6ill'O'~5 •U3 2
1
20 19iJl
II1716115a1311121110...... L.....-~
Connector"B"
,...,.....-~~'is"'-"'r"""".~~r"'-&765~'o"~•3ru2I
1&17iJl1615ullJ12IliJllO9L...,..L-,_\-L..,-
Z04530
r
!rfl176~54 3 21~
m2019lI:8171611514131211~
Connector"A"
~e@j
AC2718
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2722
Connector ”A”Connector ”B”
AC2723
Connector ”A”
Connector ”B”
AC2722
Connector ”A”
Connector ”B”
AC2723
Connector ”A”
Connector ”B”
AC−70
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
1996 LAND CRUISER (RM451U)
(d) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
3. Mode Control Switch: INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal A−9 and the negative ( −) lead to terminal B−16.
(b) Push each of the mode buttons in and check that their in- dicator light lights up.
(c) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
4. Blower Speed Control Switch: INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal A−9 and the negative ( −) lead to terminal B−16.
(b) Push each of the blower speed control buttons in and check that their indicator light lights up.
(c) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
c
r
1rf1~716[lJ';W5413 211
1\E~g1~171611514[.3]12111~
-r...'onnector"A"(
IeCBI
AC2719
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09805
Connector ”A”Connector ”B”
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC−71
1996 LAND CRUISER (RM451U)
5. A/C or DEF Switch:
INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal
A−9 and the negative ( −) lead to terminal B−18.
(b) Push the A/C or DEF switch button in and check that the indicator light lights up.
(c) Then, connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
6. INSPECT AIR INLET CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FRESHA8 − A19Continuity
RECIRCA8 − A18Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
7. INSPECT MODE CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FACEA14 − B16Continuity
BI−LEVELA12 − B16Continuity
FOOTA7 − B16Continuity
FOOT −DEFB11 − B16Continuity
DEFB4 − B16Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
8. INSPECT BLOWER SPEED CONTROL SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFFA10 − B16Continuity
LOA1 − B16Continuity
M1B9 − B16Continuity
M2B10 − B16Continuity
HIB13 − B16Continuity
Connector"A"
Connector"B"
Connector"A"
Connector"A"
...-~~IIB1~t•7 ,3 2I
20Itl'17"lIB,,113121110
e-20-2-C
In,•71'fIl';;l1oT~312I1\
[20It..117,,110141131211110II
0-20-2-<:.-18-2-B
AC2726
AC2727
219129
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04536
AC2SO−04
Z15447
−
AIR CONDITIONING REAR HEATER SWITCH
AC−77
1404
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER SWITCH
INSPECTION
1. REMOVE INSTRUMENT CLUSTER FINISH CENTER
PANEL WITH A/C CONTROL ASSEMBLY
2. REMOVE REAR HEATER SWITCH
3. INSPECT INDICATOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative ( −) lead to terminal 1.
(b) Push each of the rear heater switch knob in and check
that their indicators lights up.
If operation is not as specified, replace the switch.
4. INSPECT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
HI1 − 4Continuity
OFF−No Continuity
LO1 − 2Continuity
Illumination circuit3 − 6Continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T6−01
AT6684
Q05731
200 mm
(7.87 in.)
0.8 − 1.5 mm
(0.031 − 0.059 in.)
−
AUTOMATIC TRANSMISSION THROTTLE CABLE
AT−11
795
Author: Date:
1996 LAND CRUISER (RM451U)
THROTTLE CABLE
ON−VEHICLE REPAIR
1. DISCONNECT THROTTLE CABLE
(a) Disconnect the cable from the throttle linkage.
(b) Disconnect the cable from the cable clamps in the engine
compartment.
(c) Remove the bolt and disconnect the cable clamp from the
torque converter clutch housing.
2. REMOVE VALVE BODY (See page AT −7)
3. REMOVE THROTTLE CABLE
Remove the retaining bolt and pull out the throttle cable.
4. REINSTALL THROTTLE CABLE
(a) To install, follow the removal procedure in reverse.
HINT:
If throttle cable is new, stake the stopper on the inner cable.
(b) Bend the cable so there is a radius of about 200 mm (7.87
in.)
(c) Pull the inner cable lightly until slight resistance is felt, and
hold it there.
(d) Stake the stopper, 0.8− 1.5 mm (0.031−0.059 in.) from the
end of outer cable.
After installation, fill ATF and check the fluid level
(See page DI−131 ).
Adjust the throttle cable (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0YZ−01
Z16651
Key Interlock Solenoid
Stop Light Switch Shift Lock Solenoid
Shift Lock Control Switch
Shift Lock Control ECU
Ignition Switch
Shift Lock
Control ECU
Stop Light
Switch
Shift Lock Solenoid
Key Interlock Solenoid
Shift Lock
Control Switch
Battery Stop
Light
MAIN
FL FL
ALT
FL
AM1
STOP ACC
IG ECU − IG CIG
IG ACC
STP P1
P2
P EKLS
SLS
−
SLS+
AT
−12
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
796
Author: Date:
1996 LAND CRUISER (RM451U)
SHIFT LOCK SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LS−01
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−1
1139
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL SYSTEM
PRECAUTION
Take care to observe the following precautions when performing inspections o\
r removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They ca\
n burst if scratched or
dropped. Hold a bulb only by its plastic or metal case. Don’t touch the glass\
part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The LAND CRUISER is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in th\
e correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in\
-
cluding removal or installation of parts, inspection or replacement), be sure t\
o read the precautionary notices
in the RS section.
3. AUDIO SYSTEM
If the negative (−) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 stations
stored in memory are erased, so be sure to note the stations and reset them af\
ter the negative ( −) terminal
cable is reconnected to the battery.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to \
precautions in the IN section.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LT−01
BE−2
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.5. Ignition SwitchBE−11
”Key unlock warning system” does not operate.
1. GAUGE Fuse (I/P F/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up. (Taillight is normal.)
1. Headlight Bulb
2. MAIN FL
3. HEAD (LH) Fuse (No.2 R/B)
4. HEAD (RH) Fuse (No.2 R/B)
5. Light Control Switch
6. Headlight Dimmer Switch
7. Wire Harness−
−
−
−
BE−14
BE−14
−
Headlight does not light up. (Taillight does not light up.)
1. Headlight Bulb
2. Light Control Switch
3. Headlight Dimmer Switch
4. Wire Harness−
BE−14
BE−14 −
Only one light comes ON.
1. Headlight Bulb
2. HEAD (LH) Fuse (No.2 R/B)
3. HEAD (RH) Fuse (No.2 R/B)
4. Wire Harness−
−
−
−
”Lo− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Hi− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Flash” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
Taillight does not light up. (Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (I/P F/B)
3. Light Control Switch
4. Taillight Control Relay (No.2 R/B)
5. Wire Harness−
−
BE−14
BE−14 −
Taillight does not light up. (Headlight does not light up.)
1. Taillight Bulb
2. MAIN FL
3. TAIL Fuse (I/P F/B)
4. Light Control Switch
5. Wire Harness−
−
−
BE−14 −
Headlight and Taillight does not light.1. Light Control Switch
2. Wire HarnessBE−14
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010