1996 TOYOTA LAND CRUISER front light

BO38Q−01
BO−46
−
BODY WINDSHIELD
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE HOOD
2. REMOVE WIPER ARMS
3. REMOVE COWL LOUVER
4. REMOVE INNER REAR VIEW MIRROR
5. REMOVE PERSONAL LIGHT ASSEMBLY
6. REMOVE PERSONAL LIGHT COVER
7. REMOVE SUN VISORS AND HOLDERS
8. REMOVE ASSIST GRIPS
9. REMOVE FRONT PILLAR GARNISHES
10. LOOSEN ROOF HEADLINING
11. REMOVE WINDSHIELD GLASS
(a) From the outside of the vehicle , cut off the weatherstrip.
NOTICE:
Do not damage the body and the glass.
(b) Push piano wire through between the body and glass from the interior.
(c) Tie both wire ends to the wooden blocks or equivalent.
NOTICE:
When separating, take care not to damage the paint or inte-
rior ornaments.
To prevent scratching the safety pad when removing the
windshield, place a plastic sheet between the piano wire
and safety pad.
(d) Cut the adhesive by pulling the piano wire around it.
(e) Remove the glass.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY WINDSHIELD
BO−49
1996 LAND CRUISER (RM451U)
(b) Clean off the sealer oozing out from the masking tape with
a clean rag saturated in cleaner.
6. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test.
(b) Seal any leaks with auto glass sealer.
Part No. 08833−00030 or equivalent
7. INSTALL ROOF HEADLINING
8. INSTALL FRONT PILLAR GARNISHES
9. INSTALL ASSIST GRIPS
10. INSTALL SUN VISORS AND HOLDERS
11. INSTALL PERSONAL LIGHT COVER
12. INSTALL PERSONAL LIGHT ASSEMBLY
13. INSTALL INNER REAR VIEW MIRROR
14. INSTALL COWL LOUVER
15. INSTALL WIPER ARMS Torque: 20 N·m(205 kgf·cm, 15 ft·lbf)
16. INSTALL HOOD Torque: 18 N·m(185 kgf·cm, 13 ft·lbf)
17. ADJUST HOOD (See page BO−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−64
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
11. REMOVE FRONT SEAT OUTER BELT SHOULDER AN-
CHOR
12. REMOVE CENTER PILLAR UPPER GARNISH
13. REMOVE FRONT SHOULDER BELT ANCHOR AD-
JUSTER
14. REMOVE NO. 1 REAR SEAT OUTER BELT SHOUL- DER ANCHOR
15. w/ No. 2 Rear Seat REMOVE NO. 2 REAR SEAT OUTER BELT SHOUL-
DER ANCHOR
16. REMOVE QUARTER AND REAR PILLAR GARNISH
17. REMOVE ASSIST GRIPS
18. REMOVE FRONT PILLAR GARNISH
19. REMOVE SUN VISORS AND HOLDERS
20. REMOVE INNER REAR VIEW MIRROR
21. REMOVE PERSONAL LIGHT ASSEMBLY AND PER- SONAL LIGHT COVER
22. REMOVE NO. 1 AND NO. 2 ROOM LIGHT
23. REMOVE BACK DOOR OPENING TRIM
24. REMOVE SLIDING ROOF OPENING MOULDING
25. REMOVE CONTROL SWITCH
(a) Remove the screw.
(b) Using a screwdriver, remove the switch cover.
(c) Remove the 2 screws and switch body, then disconnect the connector.
(d) Remove the 2 screws and bracket.
26. REMOVE ROOF HEADLINING
(a) Using the clip remover, remove the 7 clips.
(b) Remove the roof headlining.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO0632
BO39M−01
BO0633
15°
45°
N10070
Full Belt Length
minus 200 mm
(7.87 in.)
−
BODY SEAT BELT
BO−93
1996 LAND CRUISER (RM451U)
SEAT BELT
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts,
nuts or sill −bar) if it has been used in a severe impact. The
entire assembly should be replaced even if damage is not
obvious.
1. All seat belts: RUNNING TEST (IN SAFE AREA)
(a) Fasten the front seat belts.
(b) Drive the car at 10 mph (16 km/h) and make a very hard stop.
Check that the belt locks and cannot be extended at this
time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly, verify the
proper operation before installation.
2. Driver ’s seat belt (ELR): STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Tilt the retractor slowly.
(d) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3. Except driver’s seat belt (ALR/ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Pull out the whole belt and measure the length of the whole belt.
Then retract the belt slightly and pull it out again.
(d) Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.
(e) Retract the whole belt, then pull it out to the full length mi-
nus 200 mm (7.87 in.).
(f) Tilt the retractor slowly.
(g) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05038
780  30 mm
30.71  1.18 in.
BR1865
0.13 sec.
0.13 sec.
ON
OFF
R05596
0.13 sec.
Braking
0.13 sec.
R05597
0.13 sec. 0.13 sec.
Braking
DI−194
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(9) Jack up the front side of the vehicle slowly, as
shown.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (10) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor.
(11) Jack down the vehicle slowly.
(c) Deceleration sensor operation check. (1) Drive the vehicle straight ahead at about 20 km/h
(12.4 mph) or more, lightly depress the brake pedal.
(2) Check that there is no change in the warning light pattern.
(3) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
moderately.
(4) Check that the warning light turns on while braking.
(5) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
strongly.
(6) Check that the warning light pattern changes while braking, as shown.
If the operation is not as specified, inspect the deceleration sen-
sor installation. If the sensor installation is OK, replace the de-
celeration sensor. (7) Stop the vehicle and turn the ignition switch OFF.
(8) Remove SST from the terminals Ts and E
1 of the
DLC1.
SST 09843−18020
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5LX−02
W03004
Rear Speed Sensor
Rear Speed Sensor Rotor
Front Speed Sensor
Stop Light Switch
ABS Warning Light
Deceleration Sensor
DLC1
ABS ECU
ABS Actuator
ABS Relay
Front Speed Sensor Rotor
DI−198
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q3−02
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−243
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, the circuit listed for that code in t\
he table below
(Proceed to the page given for that circuit.).
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
Normal
( DI−271 )System normal−OFF
Source voltage dropBattery
 Airbag sensor assemblyON
11
( DI−247 )
Short in squib circuit (to ground)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib )
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
12
( DI−254 )
Short in squib circuit (to B+)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
14
( DI−260 )
Open in D squib circuitSteering wheel pad (D squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
31
( DI−265 )Airbag sensor assembly malfunctionAirbag sensor assemblyON
54
( DI−267 )Open in P squib circuitFront passenger airbag assembly (P squib)
 Airbag sensor assembly
 Wire harness
ON
HINT:
When the SRS warning light remains lit up and the DTC is the normal code\
, this means a source drop
voltage.
This malfunction is not stored in memory by the airbag sensor assembly a\
nd if the power source volt-
age returns to normal, the SRS warning light will automatically go out.
When 2 or more codes are indicated, the codes will be displayed in numer\
al order starting from the
lowest numbered code.
If a code not listed on the chart is displayed, the airbag sensor assemb\
ly is faulty.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05894 AB0117H00001
Airbag Sensor
Assembly
LOCK
Spiral
Cable
D Squib P Squib
R14285 AB0119H00021
ON
Airbag Sensor Assembly
ACC IG2
(+)
(−)
DI−272
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Preparation.
PREPARATION:
(a) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(b) Remove steering wheel pad (See page SR−11).
(c) Disconnect connector of front passenger airbag assem- bly (See page RS−22 ).
(d) Disconnect connector of airbag sensor assembly (See page RS−33 ).
CAUTION:
Store the steering wheel pad with the front surface facing
upward.
2 Check source voltage.
PREPARATION:
(a) Connect negative ( −) terminal cable to battery.
(b) Turn ignition switch ON.
CHECK:
Measure voltage at IG2 or ACC on sensor and operate electric
system. (defogger, wiper, headlight, heater blower, etc.)
OK:
Voltage: 10 − 14 V
NG Check the harness between battery and airbag sensor assembly, and check the battery and
charging system.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010