1996 TOYOTA LAND CRUISER sensor

BE6653A00499A00488
Throttle Position Sensor
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC IDL1
E2 E112V
5V
ON
BE6653
A00496 A00498
A00489
4
3
2
11
11
9
10
E5
E5
E5 E5
VTA1
ECM
VCC IDL1
E2 12V
5V
ON
Throttle Position
Sensor
E5 Connector
−
DIAGNOSTICS ENGINE
DI−95
1996 LAND CRUISER (RM451U)
4 Check for short in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: OFF
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
5 Check for short in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Disconnect E5 connector of ECM.
HINT:
Throttle position sensor connector is disconnected.
(c) Turn ignition switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
OK:
CTP switch signal: OFF
OK Short in harness between ECM and throttle position sensor, repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00492
43
2
11
11
9
10
E5
E5
E5 E5
VTA
ECM
VCC
IDL
E2E1 12V
5V
ON
Throttle Position Sensor
DI−96
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check for open and short in harness or ECM.
PREPARATION:
(a) Disconnect throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals 1 and 2 of throttle position
sensor connector.
OK:
Voltage: 9 − 14 V
OK Confirm good connection at sensor. If OK, replace throttle position sensor.
NG
2 Check for open and short in harness and connector between throttle posit\
ion sensor and ECM (See page IN−28).
NG Open or short in harness between ECM and
throttle position sensor.
OK
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−102
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P1335 Crankshaft Position Sensor Circuit Malfunction (during engine running)
CIRCUIT DESCRIPTION
Refer to DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction\
) on page DI−62.
DTC No.DTC Detecting ConditionTrouble Area
P1335No crankshaft position sensor signal (NE signal) to ECM with
engine speed 1,000 rpm or more
Open or short in crankshaft position sensor circuit for NE
signal
 Crankshaft position sensor for NE signal
 Starter
 ECM
WIRING DIAGRAM
See DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction) \
for WIRING DIAGRAM and INSPEC-
TION PROCEDURE.
DI5PR−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−107
1996 LAND CRUISER (RM451U)
DTC P1605 Knock Control CPU Malfunction
CIRCUIT DESCRIPTION
Refer to DTC P0325, P0330 (Knock Sensor 1, 2 Circuit Malfunction) on page DI−59.
DTC No.DTC Detecting ConditionTrouble Area
P1605Engine control computer malfunction (for knock control)ECM
WIRING DIAGRAM
Refer to P0325, P0330 (Knock Sensor 1, 2 Circuit Malfunction) on page DI−59.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P1605) being output?
YES Go to relevant DTC chart.
NO
Check and replace ECM (See page IN−28 ).
DI5PU−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22480
BatteryStarter
FL MAIN
FL AM2EFI
EFI Main Relay
IG Switch IG
ST
Park/Neutral
Position SwitchCircuit Opening
Relay
Fuel Pump Relay
Fuel Pump
From Crankshaft Position
Sensor Fuel Pump
Resistor
(STA Signal)
(NE Signal) MRLY
FC
STA
NE
Tr1
Tr2
ECM
IGN FPR
−
DIAGNOSTICS ENGINE
DI−11 5
1996 LAND CRUISER (RM451U)
Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows form terminal ST of the igni\
tion switch to
terminal STA of ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr1 is turned ON, current flows to coil of the circuit
opening relay, the relay switches on, power is supplied to the fuel pump and the fuel\
pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr1 ON (circuit opening relay ON) and
the fuel pump also keeps operating.
The fuel pump speed is controlled at 2 levels (high speed or low speed) b\
y the condition of the engine (start-
ing, light load, heavy load). When the engine starts (STA ON), Tr2 in the ECM is OFF, so battery voltage is
applied directry to the fuel pump. Fuel pump operates at high speed.
After the engine starts, during idling or light loads, since Tr2 goes ON, power is supplied to the fuel pump
via the fuel pump resistor.
Fuel pump operates at low speed.
DI5PY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KB−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−143
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed for that code i\
n the table below and pro-
ceed to the page given.
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P0500
( DI−153 )Vehicle Speed Sensor Malfunc-
tion
(No. 1 Vehicle Speed Sensor)Open or short in No. 1 vehicle speed sensor circuit
 No. 1 vehicle speed sensor
 ECM

P0710
( DI−154 )Transmission Fluid Temperature
Sensor Malfunction
(ATF Temperature Sensor) Open or short in ATF temperature sensor circuit
 ATF temperature sensor
 ECM

P0750
( DI−156 )Shift Solenoid A Malfunction
(Shift Solenoid Valve No. 1)Shift solenoid valve No. 1 is stuck open or closed
 Valve body is blocked up or stuck
P0753
( DI−157 )Shift Solenoid A Electrical
Malfunction
(Shift Solenoid Valve No. 1)Open or short in shift solenoid valve No. 1 circuit
 Shift solenoid valve No. 1
 ECM

P0755
( DI−156 )Shift Solenoid B Malfunction
(Shift Solenoid Valve No. 2)Shift solenoid valve No. 2 is stuck open or closed
 Valve body is blocked up or stuck
P0758
( DI−157 )Shift Solenoid B Electrical
Malfunction
(Shift Solenoid Valve No. 2)Open or short in shift solenoid valve No. 2 circuit
 Shift solenoid valve No. 2
 ECM

P0770
( DI−161 )Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)Shift solenoid valve SL is stuck open or closed
 Valve body is blocked up or stuck
 Lock− up clutch

P0773
( DI−163 )Shift Solenoid E Electrical
Malfunction
(Shift Solenoid Valve SL)Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM

P1700
( DI−166 ) Speed Sensor No. 2 Circuit
Malfunction
(No. 2 Vehicle Speed Sensor)Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM

P1780
( DI−169 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*:  ...MIL light up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KD−02
Q08236
No. 1 Vehicle
Speed Sensor
O/D OFF Indicator Light
MIL
Pattern Select Switch O/D Main Switch
DLC1
Shift Solenoid Valve SL
ECM
Stop Light Switch L4 Position Sensor
Park/Neutral Position Switch No. 2 Vehicle Speed Sensor
Shift Solenoid Valve No. 2
Shift Solenoid Valve No. 1
Engine Coolant Temperature Sensor
Throttle Position Sensor
ATF Temperature Sensor
DLC3
Transfer Neutral
Position Switch
DI−144
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KH−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−147
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but\
the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and\
proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle repair Matrix Chart
Chapter 3: Off−Vehicle repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given i\
n Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to cont\
inue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any\
of the other circuits, then check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion6. On−vehicle repair matrix chart
7. Off −vehicle repair matrix chart−
−
Vehicle does not move in a particular position or positions1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No up− shift (1st → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up −shift (2nd → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up− shift (3rd → O/D)
1. O/D main switck& O/D OFF indicator light circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Throttle position sensor circuit
6. Park/neutral position switch circuit
7. O/D cancel signal circuit
8. Engine coolant temp. sensor circuit
9. On−vehicle repair matrix chart
10.Off −vehicle repair matrix chart
11. ECMDI−174
DI−157 DI−87
DI−166 DI−35
DI−169
DI−172 DI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010