1996 TOYOTA LAND CRUISER Pump

SS1EW−01
−
SERVICE SPECIFICATIONS LUBRICATION
SS−15
138
Author: Date:
1996 LAND CRUISER (RM451U)
LUBRICATION
SERVICE DATA
Oil pressureat idle speed
at 3,000 rpm29 kPa (0.3 kgf/cm2, 4.3 psi) or more
245 − 490 kPa (2.5 − 5.0 kgf/cm2, 36 − 71 psi)
Oil pumpBody clearance STD
Maximum
Side clearance STD
Maximum
Tip clearance STD
Maximum0.100 − 0.170 mm (0.0039 − 0.0067 in.)
0.30 mm (0.0118 in.)
0.030 − 0.090 mm (0.0012 − 0.0035 in.)
0.15 mm (0.0059 in.)
0.030 − 0.160 mm (0.0012 − 0.0063 in.)
0.25 mm (0.0098 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EX−04
SS−16
−
SERVICE SPECIFICATIONS LUBRICATION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pan x Drain plug2525018
Oil pump x Relief valve plug4950036
Drive belt idler pulley x Oil pump4344032
Oil strainer x No. 1 oil pan2020014
Baffle plate x No. 1 oil pan9.09078 in.·lbf
No. 1 oil pan x Cylinder block 14 mm head bolt
12 mm head bolt44
20440
20032
14
No. 1 oil pan x Oil pump (Timing chain cover)2020014
No. 2 oil pan x No. 1 oil pan Bolt
Nut7.8
8.880
9069 in.·lbf
78 in.·lbf
No. 1 oil pan x Transmission housing7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
A/C compressor bracket x No. 1 oil pan3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil cooler cover x Relief valve plug3737527
Oil cooler x Oil cooler cover1717012
Oil cooler cover x Cylinder block2121015
No. 1 exhaust manifold x Cylinder head3940029
No. 1 exhaust manifold x Heat insulator1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission housing2424017
Front exhaust pipe x No. 1 support bracket Clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
Oil check valve x Cylinder block2525018
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS−26
−
SERVICE SPECIFICATIONS TRANSFER
149
Author: Date:
1996 LAND CRUISER (RM451U)
Center differential side gear thrust washer thickness
1.70 mm (0.0669 in.)
1.85 mm (0.0728 in.)
2.00 mm (0.0787 in.)
2.15 mm (0.0846 in.)
2.30 mm (0.0906 in.)
2.45 mm (0.0965 in.)
2.60 mm (0.1024 in.)
2.75 mm (0.1083 in.)
2.90 mm (0.1142 in.)
3.05 mm (0.1201 in.)
Front drive gear piece snap ring thickness
Mark A
B
C
D E
F
G H J
K
L2.00 mm (0.0787 in.)
2.10 mm (0.0827 in.)
2.20 mm (0.0866 in.)
2.30 mm (0.0906 in.)
2.40 mm (0.0945 in.)
2.50 mm (0.0984 in.)
2.60 mm (0.1024 in.)
2.70 mm (0.1063 in.)
2.80 mm (0.1102 in.)
1.80 mm (0.0709 in.)
1.90 mm (0.0748 in.)
Front extension housing ball bearing snap ring thickness Mark A
B1.7 mm (0.0669 in.)
1.8 mm (0.0709 in.)
Front output shaft hub snap ring thickness Mark A
B
C
D E1.8 mm (0.0709 in.)
1.9 mm (0.0748 in.)
2.0 mm (0.0787 in.)
2.1 mm (0.0827 in.)
2.2 mm (0.0866 in.)
Oil pump driven rotor body clearance STD
Max.0.08 − 0.17 mm (0.0031 − 0.0067 in.)
0.17 mm (0.0067 in.)
Oil pump driven rotor body tip clearance STD
Max.0.05 − 0.15 mm (0.0020 − 0.0059 in.)
0.15 mm (0.0059 in.)
Oil pump side clearance STD
Max.0.03 − 0.10 mm (0.0012 − 0.0039 in.)
0.10 mm (0.0039 in.)
Rear extension housing ball bearing snap ring thickness Mark A
B1.7 mm (0.0669 in.)
1.8 mm (0.0709 in.)
Rear output shaft ball bearing snap ring thickness Mark 1
2
3
41.95 mm (0.0768 in.)
2.05 mm (0.0807 in.)
2.15 mm (0.0847 in.)
2.25 mm (0.0886 in.)
Motor actuator
Terminal 2 − Terminal 3 STD resistance
Terminal 2 or 3 − Body ground STD resistance
0.3 − 100 Ω
More than 0.5 MΩ
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E9−02
−
SERVICE SPECIFICATIONS TRANSFER
SS−27
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pump plate and separator x Rear extension housing4.95043 in.·lbf
Oil pump cover x Rear extension housing4.95043 in.·lbf
Lever lock pin121209
Oil strainer x Rear case4.95043 in.·lbf
Oil receiver x Front case121209
Case cover x Rear case3738027
Rear extension housing x Rear case3738027
Front extension housing x Front case3738027
Center differential lock Indicator switch3738014
L4 position switch3738027
Neutral position switch3738027
Screw plug x Front case1919014
Screw plug x Rear extension housing2930022
Motor actuator x Front case1818513
Differential front case x Differential rear case
Temporarily tighten98
881,00090072
65
Front case x Rear case3738027
Rear case x Retainer3940028
Dynamic damper x Rear extension housing3738027
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EG−02
−
SERVICE SPECIFICATIONS STEERING
SS−37
160
Author: Date:
1996 LAND CRUISER (RM451U)
STEERING
SERVICE DATA
ON−VEHICLE INSPECTION
Steering wheel freeplay Maximum40 mm (1.57 in.)
Fluid level riseMaximumBelow 5 mm (020 in.)
Fluid pressure at idle speed with valve closed Minimum9,316 kPa (95 kgf/cm2, 1,351 psi)
Steering effort at idle speedMaximum8.3 N·m (85 kgf·cm, 73 in.·lbf)
TILT STEERING COLUMN
Pawl stopper alignment mark 1 or A
2 or B
3 or C
4 or D 5 or E12.65 − 12.75 mm (0.4980 − 0.5020 in.)
12.55 − 12.65 mm (0.4941 − 0.4980 in.)
12.45 − 12.55 mm (0.4902 − 0.4941 in.)
12.35 − 12.45 mm (0.4962 − 0.4902 in.)
12.25 − 12.35 mm (0.4823 − 0.4862 in.)
PS VANE PUMP
Oil clearance between pump shaft and bushing STD
Maximum0.03 − 0.05 mm (0.0012 − 0.0020 in.)
0.07 mm (0.0028 in.)
Vane plate height Minimum8.6 mm (0.339 in.)
Vane plate thickness Minimum1.397 mm (0.05500 in.)
Vane plate length Minimum14.991 mm (0.59016 in.)
Vane plate and pump rotor groove clearanceMaximum0.033 mm (0.00130 in.)
Vane plate lengthPump rotor mark
None1
2
Cam ring mark
2
3
4
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
Spring free length STD35 − 37 mm (1.38 − 1.46 in.)
Vane pump rotaing torque Maximum0.3 N·m (2.8 kgf·cm, 2.4 in.·lbf)
PS GEAR
Worm gear valve body ball clearanceMaximum0.15 mm (0.059 in.)
Cross shaft adjusting screw thrust clearance STD0.03 − 0.05 mm (0.0012 − 0.0020 in.)
Worm gear preload0.3 − 0.5 N·m (3 − 5.5 kgf·cm, 2.6 − 4.8 in.·lbf)
Total preload0.74 − 1.08 N·m (7.5 − 11.0 kgf·cm, 6.5 − 9.6 in.·lbf)
STEERING LINKAGE
Tie rod length Approximately1.207 mm (47.51 in.)
Relay rod lengthApproximately1.085 mm (42.72 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EH−02
SS−38
−
SERVICE SPECIFICATIONS STEERING
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
TILT STEERING COLUMN
Steering wheel set nut3435025
Steering wheel pad set screw (T orx screw)9.09078 in.·lbf
Steering column assembly set nut and bolt2525018
Sliding yoke sub−assembly x Worm gear valve body shaft3435025
Sliding yoke sub −assembly x Intermediate No. 2 shaft3435025
Universal joint x Intermediate No. 2 shaft3435025
Main shaft assembly x Universal joint3435025
Turn signal bracket set bolt4.95043 in.·lbf
Tilt sub lever side pawl set bolt x Nut5.96052 in.·lbf
Tilt lever retainer set nut1515011
Tilt lever assembly set bolt2.93026 in.·lbf
Compression spring set bolt7.88069 in.·lbf
Column hole cover x Lower dust seal5.96052 in.·lbf
Column hole cover x Body131309
Link joint protector set bolt121209
PS VANE PUMP
Pressure feed tube set union bolt5657542
PS vane pump assembly set nut3637027
Suction port union set bolt131309
Vane pump drive gear set nut7475054
Pressure port union6970051
PS GEAR
Pressure tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Return tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Gear housing assembly x Body1421,450105
Pitman arm x Cross shaft1771,800130
Cross shaft adjusting screw set nut4647034
Side cover x Gear housing6162045
Plunger guide nut2020515
Worm gear valve body assembly x Gear housing6162045
Control valve shaft x Sliding york sub −assembly3435025
STEERING LINKAGE
Pitman arm x Cross shaft1771,800130
Pitman arm x Relay rod9192567
Tie rod clamp bolt3737527
Tie rod x Knuckle arm9192567
Relay rod x Steering damper7475054
Steering damper x Steering damper bracket7475054
Steering damper bracket x Body7475054
Relay rod clamp bolt3737527
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BH−01
Q08383
Center Differential Control
Couping Assembly
Snap ring Vehicle Speed sensor
Drive Gear Ball Bearing
 Snap Ring
Snap Ring
Oil Pump Plate
Drive Rotor
Oil Pump Cover
Rear Extension housing
Oil Pump Drive Shaft Ball
Spring 
Screw Plug
Valve Seat

Dust Deflector
 Oil Seal Seal Ring
Rear Output Shaft
 Non− reusable Part
 Precoated part Separator
Driven Rotor
−
TRANSFER REAR EXTENSION HOUSING
TR−29
839
Author: Date:
1996 LAND CRUISER (RM451U)
REAR EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BI−01
Q00530
Q08384
Q02549
Q07138
TR−30
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE OIL PUMP DRIVE SHAFT
2. REMOVE OIL PUMP COVER
(a) Using a torx socket wrench (T30), remove the 3 screws.
(b) Install the 2 suitable bolts to the pump cover.
(c) Remove the pump cover from the rear extension housing.
3. REMOVE DRIVE ROTOR FROM DRIVEN ROTOR
4. REMOVE DRIVEN ROTOR FROM REAR EXTENSION HOUSING
5. REMOVE SCREW PLUG, SPRING, BALL AND VALVE SEAT
(a) Using a hexagon wrench, remove the screw plug.
(b) Using a magnetic finger, remove the spring, ball and valve
seat from the rear extension housing.
6. REMOVE CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the coupling assembly from the rear extension housing.
7. REMOVE SEPARATOR AND OIL PUMP PLATE
Remove the 3 bolts, separator and oil pump plate.
8. REMOVE VEHICLE SPEED SENSOR DRIVE GEAR
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the vehicle speed sensor drive gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010