Page 1147 of 1399
SA2464
SA−84
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
19. REMOVE RING GEAR
(a) Place matchmarks on the ring gear and differential case.
(b) Remove the 12 ring gear set nuts and bolts.
(c) Using a plastic hammer, tap on the ring gear to remove it
from the differential case.
20. CHECK DIFFERENTIAL CASE RUNOUT
(a) Install the differential case in the differential carrier and tighten the adjusting nut just to where there is no play in
the bearing.
(b) Using a dial indicator, measure the differential case run- out.
Maximum case runout: 0.07 mm (0.0028 in.)
(c) Remove the differential case.
21. w/o DIFFERENTIAL LOCK: REMOVE SIDE BEARINGS FROM DIFFERENTIAL
CASE
Using SST, remove the 2 side bearings from the differential
case. SST 09950 −40010 (09951 −04010, 09952 −04010,
09953 −04020, 09955 −04060, 09957 −04010,
09958 −04010), 09950−60010 (09951 −00480)
22. w/ DIFFERENTIAL LOCK:
REMOVE SIDE BEARINGS FROM DIFFERENTIAL
CASE
(a) Using SST, remove the side bearing (ring gear side). SST 09950 −40010 (09951 −04010, 09952 −04010,
09953 −04020, 09955 −04060, 09957 −04010,
09958 −04010), 09950−60010 (09951 −00480)
HINT:
Fix the claws of SST to the notches in the differential case.
(b) Using SST, 4 bolts and a press, remove the side bearing (cover side).
SST 09550−10012 (09557 −10010),
09950 −70010 (09951 −07150)
HINT:
Fix the claws of SST to the notches in the differential case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1148 of 1399
SA2475
SST
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−85
1996 LAND CRUISER (RM451U)
23. w/o DIFFERENTIAL LOCK:
DISASSEMBLE DIFFERENTIAL CASE
(a) Remove the pinion shaft pin and washer.
(b) Remove these parts from the differential case:
Pinion shaft
2 Pinion gears
2 Pinion gear thrust washers
2 Side gears
2 Side gear thrust washers
24. w/ DIFFERENTIAL LOCK: DISASSEMBLE DIFFERENTIAL CASE
(a) Place matchmarks on the case and cover.
(b) Using a torx socket wrench, remove the 5 set bolts and 3
pinion shaft pins.
(c) Using the 2 cover installation bolts, separate the cover and case.
(d) Remove these parts from the differential case:
2 Side gears
2 Side gear thrust washers
4 Pinion gears
4 Pinion thrust washers
3 Pinion shafts
Pinion shaft holder
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1149 of 1399
SA1VI−01
SA2419
SST
SA2418SST
SA−86
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE DUST DEFLECTOR
Using SST and a press, remove the dust deflector. SST 09950−00020
2. INSTALL DUST DEFLECTOR
Using SST and a press, install a new dust deflector. SST 09726−40010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1150 of 1399
SA0510
SA1VJ−04
Z06893
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−87
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. w/o DIFFERENTIAL LOCK:
ASSEMBLE DIFFERENTIAL CASE
(a) Apply all of the sliding and rotating surfaces with gear oil.
(b) Install the 2 thrust washers and side gears. Using the table below, select the thrust washers which will
ensure that the backlash is within the specification.
Try to select washers of the same size for both sides.
Backlash: 0.02 − 0.20 mm (0.0008−0.0079 in.)
Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
1.60 (0.063)1.90 (0.075)
1.75 (0.069)2.05 (0.081)
(c) Install the side gears with the side gear thrust washers,
pinion gears, pinion gear thrust washers and pinion shaft.
HINT:
Align the hole for the pinion shaft and differential case hole.
(d) Using a dial indicator, measure the side gear backlash with holding the one pinion gear toward the case.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
If the backlash is not within the specification, install a thrust
washer of different thickness.
(e) Install the pinion shaft pin and washer.
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1151 of 1399
SA0510
R08274
R08276
R13246
SA−88
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
2. w/ DIFFERENTIAL LOCK:
MEASURE SIDE GEAR BACKLASH
(a) Apply all of the sliding and rotating surfaces with gear oil.
(b) Install the thrust washer to the side gear.
(c) Install the thrust washer to the pinion gear.
(d) Install the side gear into the case.
(e) Install the holder into the case.
(f) Install the 4 pinion gears with the thrust washers.
(g) Align the pinion shaft hole and case pinion shaft pin hole,
and install the pinion shaft.
(h) Install the side gear to the cover.
(i) Align the matchmarks and install the case and cover.
(j) Using a torx socket wrench, torque the 5 bolts and 3 pin-
ion shaft pins.
Torque: 58 N·m (590 kgf·cm, 43 ft·lbf)
(k) Using a dial indicator, with holding the side gear and mea- sure the backlash.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
HINT:
Measure at all 4 locations.
If the backlash is not within the specification, install the thrust
washer of a different thickness. Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
1.60 (0.063)1.90 (0.075)
1.75 (0.069)2.05 (0.081)
(l) After measuring backlash, remove the 5 set bolts and 3pinion shaft pins.
3. w/ DIFFERENTIAL LOCK: ASSEMBLE DIFFERENTIAL CASE
(a) Clean the thread of the bolts, pinion shaft pins, case and
cover with the white gasoline.
(b) Coat the threads of the bolts and pinion shaft pins with adhesive.
Adhesive: Part No. 08833 −00070, THREE BOND 1324
or equivalent
(c) Align the matchmarks, install the case and cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1152 of 1399
SA1143
Boiling Water
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−89
1996 LAND CRUISER (RM451U)
(d) Using a torx socket wrench, torque the 5 bolts and 3 pin-
ion shaft pins.
Torque: 58 N·m (590 kgf·cm, 43 ft·lbf)
4. INSTALL SIDE BEARINGS
(a) w/o Differential lock: Using SST and a press, install the 2 side bearings on the
differential case.
SST 09315−00022, 09550 −10012 (09558−10010)
(b) w/ Differential lock:
Using SST and a press, install the 2 side bearings on the
differential case.
SST 09550−60010, 09550 −10012 (09558−10010)
5. INSTALL RING GEAR ON DIFFERENTIAL CASE
(a) Clean the contact surfaces of the differential case and ring gear.
(b) Heat the ring gear to about 100° C (212°F) in boiling wa-
ter.
(c) Carefully remove the ring gear from the boiling water.
(d) After the moisture on the ring gear has completely evapo-
rated, quickly install the ring gear to the differential case.
(e) Align the matchmarks on the ring gear and differential case.
(f) Temporarily install the set bolts and nuts so that the bolt
holes in the ring gear and differential case are not misa-
ligned.
NOTICE:
Install the bolts so that the tapered part of the bolt is on the
ring gear side. The ring gear set nuts should not tighten un-
til the ring gear has cooled sufficiently.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1153 of 1399
SA2425
SSTSST
Front
Rear
SA3102
SST
R13414
SST
SA−90
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(g) After the ring gear cools down enough, tighten the set
bolts uniformly and a little at a time.
Torque: 110 N·m (1,125 kgf·cm, 81 ft·lbf)
6. CHECK RING GEAR RUNOUT
(a) Install the differential case onto the carrier and tighten the
adjusting nut just to where there is no play in the bearings.
(b) Using a dial indicator, check the ring gear runout. Maximum runout: 0.10 mm (0.0039 in.)
(c) Remove the differential case.
7. INSTALL DRIVE PINION FRONT AND REAR BEARING
OUTER RACES
(a) Front side: Using SST and a press, install the 2 outer races.
SST 09950−60020 (09951 −00710),
09950 −70010 (09951 −07150)
(b) Rear side: Using SST and a press, install the 2 outer races.
SST 09950−60020 (09951 −00890),
09950 −70010 (09951 −07150)
8. INSTALL DRIVE PINION REAR BEARING
(a) Install the washer on the drive pinion.
HINT:
First fit a washer with the same thickness as the washer which
was removed, then after checking the tooth contact pattern, re-
place the washer with one of a different thickne ss if necessary.
(b) Using SST and a press, install the rear bearing onto the drive pinion.
SST 09506−35010
9. TEMPORARILY ADJUST DRIVE PINION PRELOAD
(a) Install the drive pinion and front bearing.
HINT:
Assemble the spacer and oil seal after adjusting the gear con-
tact pattern.
(b) Install the oil slinger.
(c) Install the companion flange with SST. SST 09550 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1154 of 1399
SA2450
SST
SA2446
R08261
R08262
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−91
1996 LAND CRUISER (RM451U)
(d) Adjust the drive pinion preload by tightening the compan-
ion flange nut.
Using SST to hold the flange, tighten the nut.
SST 09330−00021
NOTICE:
Coat the nut and screw of the drive pinion with gear oil. As
there is no spacer, tighten a little at a time, being careful not
to overtighten.
(e) Using a torque wrench, measure the preload. Preload (at starting):
New bearing
1.3 − 2.0 N·m (13 − 20 kgf·cm, 11.3 − 17.4 in.·lbf)
Reused bearing
0.7 − 1.0 N·m (7 − 10 kgf·cm, 6.1 − 8.7 in.·lbf)
HINT:
Measure the total preload after first turning the bearing clock-
wise and counterclockwise several times to make the bearing
smooth.
10. w/o DIFFERENTIAL LOCK: INSTALL DIFFERENTIAL CASE IN CARRIER
(a) Place the 2 bearing outer races on their respective bear- ings. Make sure that the left and right outer races are not
interchanged.
(b) Install the case in the carrier.
HINT:
Make sure that there is backlash between the ring gear and
drive pinion.
11. w/ DIFFERENTIAL LOCK: INSTALL DIFFERENTIAL CASE IN CARRIER
(a) Place the 2 bearing outer races on their respective bear- ings. Make sure that the left and right races are not inter-
changed.
(b) Install the assembled plate washer onto the side bearing.
(c) Install the differential case in the carrier.
(d) Make the plate washer and bearing smooth by tapping on
the ring gear with a plastic hammer.
HINT:
If it is difficult to install the differential case into the carrier, re-
place the plate washer with a thinner one.
However, select a plate washer that allows no clearance be-
tween it and the carrier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
