1996 TOYOTA LAND CRUISER differential

Z07254
M3 M4 M1 M2
Z07255
Wire Harness Side
SA−102
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
959
Author: Date:
1996 LAND CRUISER (RM451U)
(6) Check the voltage between the terminals of the Diff.
lock ECU when switching the Diff. lock control
switch with the speedometer, registering approx. 8
km/h (5 mph) or more.
(7) Check that the indicator lights blink when center Diff. lock release mode is set.
Diff. lock is released for both the front wheels and
rear wheels at this time.
(8) Return the Diff. lock control switch to OFF.
(9) Stop the engine and lower the vehicle.
2. INSPECT DIFF. LOCK SYSTEM CIRCUIT
(a) Inspect the system circuit with connector disconnected. Disconnect the connector from the Diff. lock ECU and in-
spect the connector on the wire harness side, as shown
in the chart.
Trouble Part/
Terminals (Symbols)ConditionSpecified V alue
Rear diff. lock actuator/
1 (M2) − 3 (M1)−Less than 100 Ω
Front diff. lock actuator/
5 (M4) − 7 (M1)−Less than 100 Ω
Body ground/
13 (GND) − Body ground−Continuity
Vehicle speed sensor/
4(SPD) − Body groundVehicle moving slowly1 pulse each 40 cm (15.75 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z07256
ECU Side
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−103
960
Author: Date:
1996 LAND CRUISER (RM451U) DIFF. fuse/
8 (IG) − Body ground
Ignition switch ONBattery positive voltage
Rear diff. lock position switch/
2 (RLP) − Body groundIgnition switch ON,
Indicator light (Rear) ONAbout 0 V
Ignition switch ON,
Indicator light (Rear) OFFBattery positive voltage
Front diff. lock position switch/ 9 (FLP) − Body ground
Ignition switch ON,
Indicator light (front) ON.About 0 V
Ignition switch ON,
Indicator light (front) OFFBattery positive voltage
Center diff. indicator switch/ 15 (4WD) − Body groud
Ignition switch ON,
Indicator light (Center diff. lock) ONAbout 0 V
Ignition switch ON,
Indicator light (Ce nter diff. lock) OFFBattery positive voltage
Differential lock control switch/
12 (R) − Body ground
Ignition switch ON,
Diff. lock control switch RR or FR RRBattery positive voltage
Ignition switch ON,
Diff. lock control switch OFFAbout 0 V
Differential lock control switch/ 6 (RF) − Body ground
Ignition switch ON,
Diff. lock control switch FR RRBattery positive voltage
Ignition switch ON,
Diff. lock control switch OFF or RRAbout 0 V
HINT:
When a signal enters the ECU to LOCK the front dif ferential and
set the rear differential to FREE (when battery positive voltage
is inputted to terminal 6 (RF) of ECU and about 0 V is inputted
to terminal 12 (R)), or a signal to FREE both the front and rear
differentials, the indicator lights keep blinking until the ignition
switch is turned off (Fail−safe function).
If the circuit is not as specified, check and repair or replace the
trouble part shown in the table above.
(b) Inspect the battery positive voltage Battery positive voltage: 10 − 14.5 V
(c) Inspect the system circuit with connector connected (1) Turn the ignition switch to the ON position.
(2) Keep the center Diff. lock condition.
(3) Remove the Diff. lock ECU.
(4) Using a voltmeter, measure the voltage when thedifferential lock control switch is in the position, as
shown below.
Terminals (Symbols)Switch PositionSTD Voltage (V)
15 (4WD) − 13 (GND)−0.5 or less
9 (FLP) − 13 (GND)FR RR0.5 or less
2 (RLP) − 13 (GND)RR or FR RR0.5 or less
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02075
Heater Main Relay
5 Relay Housing
Metallic Parts
3
2
41
Z07257
Free−Lock
Lock−Free
Heater
Main
Relay Battery Battery
Heater
Main
Relay
SA−104
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
961
Author: Date:
1996 LAND CRUISER (RM451U) 3 (M1) −
1 (M2)
OFF − RR
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
1 (M2) − 3 (M1)RR − OFF
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
7 (M3) − 5 (M4)OFF or RR − FR RR
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
5 (M4) − 7 (M3)FR RR − RR or OFF
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
If the circuit is not as specified, replace the ECU.
(d) Install the ECU in place.
3. INSPECT DIFF. LOCK ACTUATOR
(a) Jack up the vehicle.
(b) Use the heater main relay and connect it, as shown below.
NOTICE:
Connect the terminals being careful not to touch the neigh-
boring terminals or metallic parts of relay housing.
(c) Rotate the tire and check that differential lock has oc- curred.
If operation is not as specified, replace the actuator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1948
21
4
Z07264
Ohmmeter
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−105
962
Author: Date:
1996 LAND CRUISER (RM451U)
4. INSPECT DIFF. LOCK CONTROL SWITCH
Inspect the switch continuity between terminals, as shown.
Switch PositionTerminalsSpecified Condition
OFF1 − 2No continuity
1 − 4No continuity
RR1 − 2No continuity
1 − 4Continuity
FR RR1 − 2Continuity
1 − 4Continuity
If continuity is not as specified, replace the switch.
5. INSPECT DIFF. LOCK POSITION SWITCH
(a) Front and Rear:
Inspect the diff. lock position switch.
(1) Check that there is continuity between terminalswhen the switch is pushed (differential connected
position).
(2) Check that there is no continuity when the switch is
free (differential disconnected position).
If operation is not as specified, replace the switch.
(b) Inspect the center diff. indicator switch.
6. INSPECT VEHICLE SPEED SENSOR AND INDICATOR
LIGHT
(a) Inspect the vehicle speed sensor (See page BE−34).
(b) Inspect the indicator light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VM−01
SA−106
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
1996 LAND CRUISER (RM451U)
DIFFERENTIAL LOCKING SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VN−02
Z07258
Z07261
SA2619
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−107
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT ACTUATOR
(a) Shifting the front differential lock.
(b) Disconnect the connector and tube.
(c) Remove the 2 nuts, bolt and actuator.
(d) Remove the O−ring from the actuator.
2. REMOVE REAR ACTUATOR
(a) Shifting the gear differential lock.
(b) Remove the actuator protector.
Remove the 2 nuts, bolt and protector.
(c) Disconnect the connectors and tube.
(d) Remove the rear Diff. lock position switch.
(e) Remove the cover. (1) Remove the 3 bolts.
(2) Using a brass bar and hammer, remove the cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2621
SA−108
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
1996 LAND CRUISER (RM451U)
(f) Remove the shift fork set bolt.
(g) Remove the 4 bolts.
(h) Using a screwdriver, pry out the actuator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VO−02
Z07259
Outside
Actuator Installation
Hole Shift Fork
R08154
3
2
1.5
50 °
108 °
Matchmark
(Groove)
SA2306
SA2420
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−109
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FRONT ACTUATOR
(a) Check that the outermost rack tooth of the shift fork is
virtually above the center line of the actuator installation
hole.
(b) Using a dry cell battery, alig n the matchmark on the pinion
with the center line of the actuator.
NOTICE:
If the pinion of the actuator is not in the specified
place, the actuator is difficult to be installed.
Do not supply the battery positive voltage between
terminals.
If the matchmark comes to the extension limit of the
rotation, do not electrify moreover.
(c) Install a new O−ring to the actuator.
(d) Apply a light coat of gear oil on the O −ring.
(e) Apply MP grease to the gear part of the actuator.
(f) Install the actuator to the differential with the 2 nuts and bolt, so that the outermost rack tooth of the shift fork will
fit matchmark of the pinion of the actuator.
HINT:
Do not damage the O −ring of the actuator.
Torque: 26 N·m (270 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010