1996 TOYOTA LAND CRUISER Terminal

A00160BE6653
P24657
ON1
−
DIAGNOSTICS ENGINE
DI−37
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal 1 of wire harness side connector and body
ground.
PREPARATION:
(a) Disconnect the throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal 1 of wire harness side con-
nector and body ground.
OK:
Voltage: 4.5 − 5.5 V
NG Go to step 5.
OK
3 Check throttle position sensor (See page SF−42).
NG Replace throttle position sensor.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00161
ON
BE6653
P24658
(+) (−)
VTA
E2
A00162
ON
VCC E2
(+) (−)
BE6653
P24659
DI−38
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check voltage between terminals VTA and E2 of ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals VTA and E2 of ECM.
OK:
Throttle valveVoltage
Fully closed0.3 − 0.8 V
Fully open3.2 − 4.9 V
NG Check for open and short in harness and
connector between ECM and throttle
position sensor (VTA line) (See page IN−28).
OK
Check and replace ECM (See page IN−28 ).
5 Check voltage between terminals VCC and E2 of ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals VCC and E2 of ECM con-
nector.
OK:
Voltage: 4.5 − 5.5 V
NG Check and replace ECM (See page IN−28 ).
OK
Check for open in harness and connector
between ECM and sensor (VCC line)
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6653
P24460A00950
ON
HT1HT2
(−) (+)
−
DIAGNOSTICS ENGINE
DI−47
1996 LAND CRUISER (RM451U)
DTC P0135 Heated Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 1)
DTC P0141 Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40.
DTC No.DTC Detecting ConditionTrouble Area
P0135
P0141
When the heater operates, heater current exceeds 2 A
(2 trip detection logic)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
Heater current of 0.25 A or less when the heater operates
(2 trip detection logic)
HINT:
Sensor 1 refers to the sensor closer to the engine body.
Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40 for WIRING
DIAGRAM.
INSPECTION PROCEDURE
1 Check voltage between terminals HT1, HT2 of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals HT1, HT2 of ECM connec-
tor and body ground.
HINT:
Connect terminal HT1 to bank 1 sensor 1.
Connect terminal HT2 to bank 1 sensor 2.
OK:
Voltage: 9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
DI5PC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22424
Fusible Link
Battery
FL AM2
F7
EA2
6
11
3
1 IG Switch
W−RW
−R
B−R B−R
IH1
14B−R
B−R
B−R
B−R
B−R B−R 2
2
2
2
2
2 1
1
1
1
1
1 W−L
W−R
W−G Y
Y−R
Y−L
BR
BR E4
E4
E4
E4
E4 E4
E4
E4 11 12
25 2
1
15
13
26
EC
Injector #10
#20 #30
#40
#50
#60
E01
E02 ECM
No.1
No.2
No.3
No.4
No.5
No.6
FI6588 FI6538
A00064
10V/
Division
GND 10V/
Division
100 m sec./Division (Idling) GND(Magnification)
1 m sec./Division (Idling)
Injection duration
−
DIAGNOSTICS ENGINE
DI−55
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Reference INSPECTION USING OSCILLOSCOPE
INJECTOR SIGNAL WAVEFORM
With the engine idling, measure between terminals #10 − #60 and E01 of ECM.
HINT:
The correct waveform is as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00165
ON
#10 #20 #40 #50
#30 #60
BE6653
P24661
−
DIAGNOSTICS ENGINE
DI−57
1996 LAND CRUISER (RM451U)
2 Check voltage of ECM terminal for injector of failed cylinder.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between applicable terminal of ECM connec-
tor and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check injector of misfiring cylinder (See page SF−29).
NG Replace injector.
OK
Check for open and short in harness and con-
nector between injector and ECM (See page
IN−28 ).
4 Check fuel pressure (See page SF−6 ).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6053P24662A08533
OFF
(−) (+)
KNK 1
KNK 2E5 Connector
DI−60
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
HINT:
DTC P0325 is for the knock sensor circuit on the front side.
DTC P0330 is for the knock sensor circuit on the rear side.
1 Check continuity between terminal KNK1, KNK2 of ECM connector and body
ground.
PREPARATION:
(a) Remove the instrument panel speaker No.1 panel (See
page SF−65 ).
(b) Disconnect the E5 connector of ECM.
CHECK:
Measure resistance between terminal KNK1, KNK2 of ECM
connector and body ground.
HINT:
Connect terminal KNK1 to knock sensor 1.
Connect terminal KNK2 to knock sensor 2.
OK:
Resistance: 1 MΩ or higher
OK Go to step 3.
NG
2 Check knock sensor (See page SF−62 ).
NG Replace knock sensor.
OK
3 Check for open and short in harness and connector between ECM and knock sensor (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24663
1
23
4
(−) (+)
P23505
G, NE signal waveforms
20 m sec/Division (Idling) 5V/DIV
G1
G2
NE
NE2
−
DIAGNOSTICS ENGINE
DI−63
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check resistance of crankshaft position sensor for NE signal.
PREPARATION:
Remove the distributor cap and disconnect distributor connec-
tor.
CHECK:
Measure resistance between terminals 1 and 4 of distributor
connector.
OK:
Resistance
Cold185 − 275 Ω
Hot240 − 325 Ω
”Cold” is from − 10°C (14F° ) to 50°C (122°F) of engine coolant
temperature sensor and ”Hot” is from 50 °C (122° F) to 100° C
(212 °F).
Reference: INSPECTION USING OSCILLOSCOPE
During cranking or idling, check between terminals G1, G2, NE,
NE2 and G− of ECM.
HINT:
The correct waveforms are as shown.
NG Replace distributor housing assembly.
OK
2 Check for open and short in harness and connector between ECM and crank-\
shaft position sensor for NE signal (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24663
2(−)
3
4 1
(+)
−
DIAGNOSTICS ENGINE
DI−65
1996 LAND CRUISER (RM451U)
DTC P0340 Camshaft Position Sensor Circuit
Malfunction
CIRCUIT DESCRIPTION
The camshaft position sensors (G1 and G2 signals) consist of a signal pla\
te and a pick up coil. The G1, G2,
signal plates each have one tooth on the outer circumference and are built int\
o the distributor. When the
camshaft rotates, the protrusion on the signal plate and the air gap on the pick \
up coil change, causing fluc-
tuations in the magnetic field and generating an electromotive force in the pick \
up coil. The ECM detects the
standard crankshaft angle based on the G1, G2 signals, detects the actual cranks\
haft angle and engine
speed by the NE signals, and detects misfire by NE2 signals.
DTC No.DTC Detecting ConditionTrouble Area
P0340No camshaft position sensor signal (G signal) to ECM with
engine speed 550 rpm or more. Open or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
WIRING DIAGRAM
Refer to DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction) o\
n page DI−62 for the WIRING
DIAGRAM.
INSPECTION PROCEDURE
1 Check resistance of camshaft position sensor.
PREPARATION:
Disconnect camshaft position sensor connector.
CHECK:
Measure resistance between terminals 2, 3 and 4 of distributor
connector.
OK:
Resistance
Cold185 − 275 Ω
Hot240 − 325 Ω
”Cold” is from − 10°C (14°F) to 50°C (122°F) of engine coolant
temperature and "Hot" is from 50°C (122°F) to 100°C (212°\
F).
Reference: INSPECTION USING OSCILLOSCOPE
Refer to page DI−62 for Reference INSPECTION USING OS-
CILLOSCOPE.
NG Replace distributor housing assembly.
OK
DI5PI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010