1996 TOYOTA LAND CRUISER Relay

DI−226
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
2 Is normal code displayed?
YES Check ABS solenoid relay. Check for short in harness and connector between ABS solenoid
relay and DLC1 (See page IN−28 ).
NO
3 Is ABS warning light go off?
YES Check for open or short in harness and connec-
tor between ECU−IG fuse and ECU (See page
IN−28 ).
NO
4 Check battery positive voltage.
PREPARATION:
Start the engine.
CHECK:
Check the battery positive voltage.
OK:
Voltage: 10 − 16 V NG Check and repair charging system.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02199
BatteryJunction
Connector
ID
W−B
B−W
ABS Control Relay
1 4
2
6 3
1
4
Motor
Relay
Solenoid
Relay
ABS ECU
ABS ECU
ABS Actuator 4
5
A7
A6
A6 A6
A4 R−L
R−L
DLC1
Short Pin
B−W
IH1
A12
ABS ECU
W
13
C10
GAUGE
2223 ABS
Warning
Light
A
A
J1
C10IH1
20
A7
A7A7
A7
EA3
EA3
2
1 B−W
B−W
B−L OO
O
Y
54
3
23 OY
DI−230
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
ABS Warning Light Circuit
CIRCUIT DESCRIPTION
If the ECU detects trouble, it lights the ABS warning light while at the same time prohibiting ABS control. At
this time, the ECU records a DTC in memory. After removing the short pin of the DLC1, connect terminals
Tc and E
1 of the DLC1 to make the ABS warning light blink and output the DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
Troubleshooting in accordance with the chart below for each trouble symptom.
ABS warning light does not light upGo to step 1
ABS warning light remains onGo to step 3
1 Check ABS warning light.
See Combination Meter Troubleshooting on page BE−2.
NG Repair bulb or combination meter assembly.
OK
DI5MJ−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14139
A6A7
Continuity
Continuity Open
1
2
5
6
3
R14140
A7
A6
(−)
(+)
Continuity
Open
1
2
5
6
3
R14144
(+) (−)4
5
A7A6
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−231
1996 LAND CRUISER (RM451U)
2 Check ABS control relay.
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connectors from the control relay.
CHECK:
Check the continuity between each terminal of the ABS control
relay.
OK:
Terminals A7 −1 and A6− 3Continuity
(Reference value 80 Ω)
Terminals A7 −5 and A7− 6Continuity
Terminals A7 −2 and A7− 5Open
CHECK:
(a) Apply battery positive voltage between terminals A7 −1
and A6−3.
(b) Check the continuity between each terminal of the ABS control relay.
OK:
Terminals A7 −5 and A7− 6Open
Terminals A7 −2 and A7− 5Continuity
CHECK:
Connect the  test lead to terminal A7−4 and the  test lead
to terminal A7−5. Check continuity between the terminals.
OK:
Continuity
If there is no continuity, connect the  test lead to terminal A7−4
and the  lead to terminal A7 −5. Recheck continuity between
terminals.
NG Replace ABS control relay.
OK
Check for open in harness and connector be-
tween DLC1 and ABS control relay and body
ground (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−232
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
3 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
4 Does ABS warning light go off if short pin is removed?
NO Check for short in harness and connector be- tween warning light and DLC1 and ECU (See
page IN−28 ).
YES
5 Check ABS control relay (See step 2).
NG Replace ABS control relay.
OK
Check for short in harness and connector be-
tween DLC1 and ABS control relay (See page
IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00497
Cruise Control ECU
B−R BATT
C17
W
W Instrument Panel Fuse Block
Fusible Link
F8 F11
F11
EA3
FL MAIN
Battery 3
ECU−B 15
2
1
N18670
Junction Block No.1
ECU−IG
Fuse
DI−328
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Back −up Power Source Circuit
CIRCUIT DESCRIPTION
The ECU back− up power source provides power even when the ignition is off and is used for DTC memory,
etc..
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check ECU −IG fuse.
PREPARATION:
Remove the ECU −IG fuse from relay block No.2.
CHECK:
Check continuity of ECU −IG fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to the ECU −IG fuse.
OK
DI5ON−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YT−01
PP−66
−
PREPARATION BODY ELECTRICAL
1996 LAND CRUISER (RM451U)
EQUIPMENT
Bulb (3.4 W)Fuel sender gauge
Seat belt warning relay
Bulb (21 W)Turn signal flasher relay
Clip removerFor removing cowl louver
Dry cell batteryFuel sender gauge
Masking tapeRear window defogger wire
Oil bathEngine oil level warning switch
Test lead
ThermometerEngine coolant temperature sender gauge
Engine oil level warning switch
Tin foilRear window defogger wire
Torque wrench
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02075
Heater Main Relay
5 Relay Housing
Metallic Parts
3
2
41
Z07257
Free−Lock
Lock−Free
Heater
Main
Relay Battery Battery
Heater
Main
Relay
SA−104
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
961
Author: Date:
1996 LAND CRUISER (RM451U) 3 (M1) −
1 (M2)
OFF − RR
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
1 (M2) − 3 (M1)RR − OFF
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
7 (M3) − 5 (M4)OFF or RR − FR RR
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
5 (M4) − 7 (M3)FR RR − RR or OFF
0.5 or less →
10 − 14.5
(Approx. 1 sec) → 0.5 or less
If the circuit is not as specified, replace the ECU.
(d) Install the ECU in place.
3. INSPECT DIFF. LOCK ACTUATOR
(a) Jack up the vehicle.
(b) Use the heater main relay and connect it, as shown below.
NOTICE:
Connect the terminals being careful not to touch the neigh-
boring terminals or metallic parts of relay housing.
(c) Rotate the tire and check that differential lock has oc- curred.
If operation is not as specified, replace the actuator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF06G−11
P05668
OhmmeterContinuity
No Continuity Ohmmeter
1
2
43
P05667
Ohmmeter Continuity
Battery
1
2
4 3
SF−54
−
SFI EFI MAIN RELAY
682
Author: Date:
1996 LAND CRUISER (RM451U)
EFI MAIN RELAY
INSPECTION
1. REMOVE EFI MAIN RELAY
LOCATION: In the engine compartment relay box.
2. INSPECT EFI MAIN RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity be-
tween terminals 1 and 3.
(b) Check that there is no continuity between terminals 2 and
4.
If continuity is not as specified, replace the relay.
3. INSPECT EFI MAIN RELAY OPERATION
(a) Apply battery voltage across terminals 1 and 3.
(b) Using an ohmmeter, check that there is continuity be-
tween terminals 2 and 4.
If operation is not as specified, replace the relay.
4. REINSTALL EFI MAIN RELAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010