1996 TOYOTA LAND CRUISER Head bolt

BO48R−01
BO−84
−
BODY FRONT SEAT (Power Adjuster Type)
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE FRONT SEAT HEADREST
2. REMOVE SIDE SUPPORT ADJUSTER KNOB
Using a screwdriver, remove the snap ring and side support ad-
juster knob.
3. REMOVE SEATBACK BOARD
(a) Remove the 2 screws.
(b) Slide the board downward to remove it.
4. REMOVE FRONT SEATBACK ASSEMBLY
(a) Using a hog ring pliers, remove the hog ring backward of seatback.
(b) Remove the 4 bolts and front seatback assembly. Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
5. REMOVE FRONT SEAT CUSHION INNER SHIELD
6. REMOVE FRONT SEAT INNER BELT
7. REMOVE FRONT SEAT CUSHION SHIELD
8. REMOVE FRONT SEAT CUSHION
(a) Remove the 4 bolts.
Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
(b) Disconnect the connector, then remove the front seat cushion.
9. REMOVE SEAT CUSHION REAR PROTECTOR
10. REMOVE RECLINING ADJUSTER INSIDE COVER
Remove the 4 screws and reclining adjuster inside cover LH
and RH.
11. REMOVE POWER ADJUST FRONT SHIELD
Remove the 2 screws and front shield.
12. REMOVE SLIDE MOTOR
(a) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
4 housing bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(b) Hold the front seat horizontal jack screw with a plier, and remove the 2 nuts and 2 washers.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of installation, apply adhesive to nut. Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1Q4−01
P05120A16078
1 Dot Mark
EM−4
−
ENGINE MECHANICAL VALVE CLEARANCE
507
Author: Date:
1996 LAND CRUISER (RM451U)
VALVE CLEARANCE
INSPECTION
HINT:
Inspect and adjust the valve clearance when the engine is cold.
1. DRAIN ENGINE COOLANT
2. REMOVE THROTTLE BODY (See page SF−45)
3. DISCONNECT ENGINE WIRE AND HEATER VALVE FROM COWL PANEL
(a) Remove the 2 bolts and disc onnect the ground strap and
engine wire.
(b) Remove the 2 bolts and disconnect the heater valve.
4. DISCONNECT HIGH −TENSION CORDS FROM SPARK
PLUGS (See page IG−1 )
5. REMOVE CYLINDER HEAD COVER
Remove the 13 bolts, cylinder head cover and gasket.
6. SET NO. 1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the timing mark ”0” of the timing chain cover.
(b) Check that the timing marks (1 and 2 dots) of the camshaft
drive and driven gears are in straight line on the cylinder
head surface as shown in the illustration.If not, turn the
crankshaft 1 revolution (360 °) and align the marks as
above.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM0494
−
ENGINE MECHANICAL VALVE CLEARANCE
EM−7
510
Author: Date:
1996 LAND CRUISER (RM451U)
9. Rear valves of No. 6 cylinder
ADJUST VALVE CLEARANCE
(a) Remove the distributor (See page IG−10).
(b) Remove the camshafts (See page EM−28).
(c) Remove the adjusting shim with a small screwdriver.
(d) Determine the replacement adjusting shim size by follow- ing the Formula or Charts:
Using a micrometer, measure the thickness of the
removed shim.
Calculate the thickness of a new shim so that the
valve clearance comes within specified value.
T ....... Thickness of removed shim
A ....... Measured valve clearance
N ....... Thickness of new shim
Intake: N = T + (A − 0.20 mm (0.008 in.))
Exhaust: N = T + (A − 0.30 mm (0.012 in.))
Select a new shim with a thickness as close as pos-
sible to the calculated value.
HINT:
Shims are available in 17 sized in increments of 0.05 mm
(0.0020 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.1299 in.).
(e) Place a new adjusting shim on the valve lifters.
(f) Install the camshafts (See page EM−54 ).
(g) Recheck the valve clearance.
(h) Install the distributor (See page IG−11 ).
10. REINSTALL CYLINDER HEAD COVER
(a) Install the gasket to the cylinder head cover.
(b) Install the cylinder head cover with the 13 bolts.
11. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS (See page IG−1 )
12. RECONNECT HEA TER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the ground strap and engine wire with the 2 bolts.
13. REINSTALL THROTTLE BODY (See page SF−48 )
14. REFILL RADIATOR WITH ENGINE COOLANT
15. CHECK AND ADJUST IGNITION TIMING (See page EM−10 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E9−01
−
ENGINE MECHANICAL TIMING CHAIN
EM−13
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE OIL
2. DRAIN ENGINE COOLANT
3. REMOVE ENGINE UNDER COVER
4. REMOVE RADIATOR (See page CO−14 )
5. DISCONNECT A/C COMPRESSOR AND BRACKET
(a) Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.
(b) Remove the 4 mounting bolts, and disconnect the com- pressor from the bracket.
HINT:
Put aside the compressor, and suspend it.
(c) Remove the 5 bolts and A/C compressor bracket.
6. REMOVE RADIATOR PIPE
(a) Disconnect the No. 2 radiator hose from the water inlet.
(b) Remove the 2 nuts and radiator pipe.
7. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
8. REMOVE CYLINDER HEAD (See page EM−28 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−23
1996 LAND CRUISER (RM451U)
15. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
16. CONNECT OIL COOLER PIPE BRACKET TO NO. 1 OIL
PA N
17. INSTALL CYLINDER HEAD (See page EM−54 )
NOTICE:
However, for the installation of the camshaft timing gear
and timing chain, follow the below procedure. Align the
blight link of the timing chain and camshaft timing gear
mark, and install them to the camshaft.
18. INSTALL WATER PUMP
Install a new gasket and water pump with the 4 bolts and 2 nuts.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
19. INSTALL RADIATOR PIPE
(a) Connect the No.2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No.1 oil
pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
20. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
21. INSTALL RADIATOR (See page CO−16 )
22. FILL ENGINE WITH OIL
23. INSTALL ENGINE UNDER COVER
24. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E3−01
EM−28
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE BATTERY AND BATTERY TRAY
(a) Disconnect the battery cables.
(b) Remove the nuts, hold −down clamp and battery.
(c) Remove the bolt and disconnect the ground strap.
(d) Remove the 5 bolts and battery tray.
3. REMOVE AIR CLEANER HOSE AND CAP
4. DISCONNECT CRUISE CONTROL ACTUATOR CABLE FROM THROTTLE BODY
5. DISCONNECT ACCELERATOR CABLE FROM
THROTTLE BODY
6. DISCONNECT THROTTLE CABLE FROM THROTTLE BODY
7. DISCONNECT ENGINE GROUND STRAPS
(a) Disconnect the ground strap from the No. 1 engine hang-
er.
(b) Disconnect the ground strap from the air intake chamber.
8. DISCONNECT CONNECTOR ON INTAKE MANIFOLD FROM LH FENDER APRON
9. DISCONNECT BRAKE BOOSTER VACUUM HOSE
10. DISCONNECT EVAP HOSE
11. DISCONNECT FUEL RETURN HOSE
12. DISCONNECT HEATER HOSES
13. DISCONNECT ENGINE WIRE AND HEATER VALVE FROM COWL PANEL
(a) Remove the 2 bolts and disconnect the engine wire and
ground strap.
(b) Remove the 2 bolts and disconnect the heater valve.
14. REMOVE NO. 2 AND NO. 3 CYLINDER HEAD COVERS
Remove the 4 bolts and head covers.
15. REMOVE DISTRIBUTOR (See page IG−10 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL CYLINDER HEAD
EM−29
1996 LAND CRUISER (RM451U)
16. DISCONNECT PS RESERVOIR TANK
Remove the 3 bolts and disconnect the reservoir tank.
17. DISCONNECT RADIATOR INLET HOSE
18. DISCONNECT NO. 3 WATER BYPASS HOSE
19. REMOVE GENERATOR (See page CH−8 )
20. REMOVE THROTTLE BODY (See page SF−45)
21. REMOVE OIL DIPSTICKS AND GUIDES FOR ENGINE AND TRANSMISSION
(a) Remove the 2 mounting bolts.
(b) Pull out the dipstick together with dipstick guide.
(c) Remove the O−ring from the dipstick guide.
22. REMOVE INTAKE MANIFOLD STAY
Remove the 2 bolts and intake manifold stay.
23. DISCONNECT FUEL INLET HOSE
Remove the union bolt and 2 gaskets, and disconnect the fuel
inlet hose from the fuel filter.
24. DISCONNECT ENGINE WIRE
(a) Disconnect the connectors. (1) Disconnect the ECT sender gauge connector.
(2) Disconnect the ECT cut switch connector.
(3) Disconnect the ECT sensor connector.
(4) Disconnect the knock sensor connector.
(5) Disconnect the crankshaft position sensor connec-tor.
(6) Remove the bolt and disconnect the engine wire from the cylinder block.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−30
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(b) Disconnect the connectors.
(1) Disconnect the knock sensor connector.
(2) Disconnect the oil level sensor connector.
(3) Disconnect the 2 connectors from the transmission.
(4) Disconnect the starter connector.
(c) Disconnect the 2 heated oxygen sensor connectors.
(d) Disconnect the PNP switch connector.
(e) Remove the 2 bolts and disconnect the engine wire from the intake manifold and cylinder block.
(f) Disconnect the PCV hose from the PCV valve.
(g) Remove the bolt holding the engine wire to the intake manifold.
(h) Disconnect the connectors. (1) Disconnect the connector for the emission controlvalve set assembly.
(2) Disconnect the 3 injector connectors.
(i) Disconnect the engine wire clamp.
(j) Disconnect the engine wire clamp.
(k) Disconnect the connectors.
(1) Disconnect the 3 injector connectors.
(2) Disconnect the EGR gas temp. sensor connector.
(l) Disconnect the clamp of the No. 6 injector wire from the bracket.
(m) Disconnect the engine wire from the cylinder head and in-
take manifold.
25. DISCONNECT NO. 2 WATER BYPASS PIPE
Remove the 3 bolts, and disconnect the bypass pipe from the
cylinder head.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010