1996 LAND ROVER DEFENDER service

ENGINE
11
REPAIR CRANKSHAFT OIL SEAL
Service repair no - 12.21.14
Remove
1.Remove crankshaft gear.
See Crankshaft gear
2.Prise out oil seal from front cover.
Refit
3.Lubricate a new crankshaft oil seal with clean
engine oil.
4.With lip side leading, drive in seal squarely using
special toolLRT-12-079.
5.Fit crankshaft gear.
See Crankshaft gear
CAMSHAFT GEAR
Service repair no - 12.65.24
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Remove centre bolt and withdraw camshaft
gear, complete with hub and retaining plate.
Refit
3.Fit camshaft gear. Tighten bolt to
80 Nm (59
lbf/ft).
4.Fit camshaft drive belt.See Camshaft drive
belt

12ENGINE
12
REPAIR CAMSHAFT OIL SEAL
Service repair no - 12.13.05
Remove
1.Remove camshaft gear.
See Camshaft gear
2.Remove camshaft oil seal from front cover using
special toolLRT-12-083.
Refit
3.Lubricate a new camshaft oil seal with clean
engine oil.
4.With lip side leading, drive in seal squarely using
special toolLRT-12-082.
5.Fit camshaft gear.
See Camshaft gear
INJECTION PUMP GEAR
Service repair no - 19.30.06
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Slacken 3 bolts on front of injector pump gear.
3.Remove special tool pin from gear.
4.Remove 3 bolts and withdraw gear and retaining
plate.
Refit
CAUTION: It is important to ensure that
when the injection pump is locked no
attempt must be made to rotate it. Take
care not to allow the crankshaft to be turned.
5.Fit gear and retaining plate. Tighten bolts to
25
Nm (18 lbf/ft).
6.Insert pin from special toolLRT-12-045in
injection pump gear and through into pump
flange.
7.Fit camshaft drive belt.
See Camshaft drive
belt

ENGINE
13
REPAIR FRONT COVER GASKET
Service repair no - 12.65.10
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Remove crankshaft gear.See Crankshaft gear
3.Remove camshaft gear.See Camshaft gear
4.Remove injection pump gear.See Injection
pump gear
5.Remove fuel injection pump.See FUEL
SYSTEM, Repair, Fuel injection pump
6.Remove engine oil sump.See Engine oil
sump
7.Remove oil pick up strainer.See Oil pick-up
strainer
8.Remove 10 bolts securing timing gear housing to
block.
9.Withdraw timing gear housing complete with
gasket.
10.Clean all gasket material from mating faces.
Refit
11.Fit slave guide studs to locate gasket.
12.Fit new gasket to cylinder block.
13.Align flats on oil pump with flats on crankshaft.
14.Fit front cover to block taking care not to damage
oil seal.15.Secure with bolts of correct length in locations
where slave studs are not fitted, see J6149.
16.Remove slave studs and fit correct length bolts.
17.Tighten all bolts to
25 Nm (18 lbf/ft).
1- 25 mm,2- 35 mm,3- 80 mm.
18.Fit oil pick-up strainer.
See Oil pick-up
strainer
19.Fit oil sump.See Engine oil sump
20.Fit fuel injection pump.See FUEL SYSTEM,
Repair, Fuel injection pump
21.Fit injection pump gear.See Injection pump
gear
22.Fit camshaft gear.See Camshaft gear
23.Fit crankshaft gear.See Crankshaft gear
24.Fit camshaft drive belt.See Camshaft drive
belt

12ENGINE
14
REPAIR ENGINE OIL SUMP
Service repair no - 12.60.44
Remove
1.Disconnect battery.
2.Drain engine oil.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray and/or
integral access panels.
See CHASSIS AND BODY, Repair, Front
undertray
orSee CHASSIS AND BODY, Repair,
Rear undertray
3.Slacken sump securing bolts.
4.Break sealant around sump flange, using a
sharp knife.
5.Remove 22 bolts and withdraw sump.
Refit
6.Clean mating faces of sump, timing gear housing
and cylinder block.
7.Apply a 2,0 mm bead of 'Hylosil RTV102' to the
sump flange, ensuring bead is applied inboard of
the bolt holes.
8.Secure sump to block with 22bolts. Tighten to
25
Nm (18 lbf/ft).
9.Refill engine oil.See LUBRICANTS, FLUIDS
AND CAPACITIES, Information, Capacities
10.Reconnect battery.OIL PICK-UP STRAINER
Service repair no - 12.60.20
Remove
1.Disconnect battery.
2.Drain engine oil.
3.Remove engine oil sump.
See Engine oil
sump
4.Remove 2 bolts securing pipe support bracket to
main bearing cap fixings.
5.Remove bolts from pipe flanges.
6.Withdraw pick-up strainer assembly.
Refit
7.Postion pick-up strainer assembly, fitting a new
'O' ring seal at oil pump connection.
8.Apply Loctite 242E to threads of bolts at main
bearing cap. Fit bolts, tighten to
9 Nm (7 lbf/ft).
9.Fit bolts to pipe flanges. Tighten to25 Nm (18
lbf/ft).
10.Fit sump.See Engine oil sump
11.Reconnect battery.

ENGINE
15
REPAIR FLYWHEEL
Service repair no - 12.53.07
Remove
1.Disconnect battery.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
assembly
4.Fit 2, long, 8 mm bolts into the clutch bolt holes,
as shown, to use as handles when lifting the
flywheel off the crankshaft.
5.Remove fan cowl.
See COOLING SYSTEM,
Repair, Fan cowl
6.Fit crankshaft pulley retainerLRT-12-080and
secure with 4 bolts, to restrain crankshaft while
removing flywheel retaining bolts.
7.Remove bolts and lift off flywheel.
Refit
NOTE: To prevent excessive flywheel
run-out, ensure that mating faces of
flywheel and crankshaft are clean.
8.Locate flywheel on crankshaft, remove lifting
bolts, and secure flywheel with new patched
retaining bolts, progressively tighten to
147 Nm
(108 lbf/ft).
9.Check the flywheel for possible run-out by
mounting a dial test indicator with the stylus in a
loaded condition resting on the flywheel face at a
radius of 114 mm (4.50 in) from the centre.
10.Turn flywheel and check that run-out does not
exceed 0,07 mm (0.003 in).
11.Should run-out be excessive, remove flywheel
and check again for irregularities on crankshaft
and flywheel mating faces and location dowel.
12.Remove crankshaft pulley retainer.
13.Fit fan cowl.
See COOLING SYSTEM, Repair,
Fan cowl
14.Fit clutch.See CLUTCH, Repair, Clutch
assembly
15.Fit gearbox.See MANUAL GEARBOX, Repair,
R380 gearbox
16.Reconnect battery.

12ENGINE
16
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
NOTE: The crankshaft rear oil seal is
retained in its own housing, if the seal
requires replacing, the complete housing
assembly (1) must be renewed. Housing and seal
assemblies are supplied with their own
former/seal guide (2) already fitted. This former
must not be removed before fitting the assembly
to the engine. If a seal and housing assembly is
received without a former/guide fitted it must be
returned to the supplier. Used formers/guides
must be discarded immediately after use, under
no circumstances should they be reused on other
assemblies.
NOTE: A different rear oil seal housing,
with integral 'O' ring seal and gasket, was
fitted on earlier engines. They must be
replaced with the current housing and gasket (3)
shown below.
1.Disconnect battery.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
assembly
4.Remove flywheel.See Flywheel
5.Remove 5 bolts and withdraw seal housing,
complete with gasket.
Refit
NOTE: The raised side of groove at the
bottom of seal housing gasket must be
fitted to cylinder block face.
6.Insert slave studs to locate seal housing gasket.
7.Position new gasket over slave studs and
crankshaft flange onto cylinder block.
8.Fit new seal housing assembly, with
former/guide in-situ, over crankshaft flange. This
action will eject former/guide.
9.Secure assembly to cylinder block, removing
slave studs individually and inserting bolts.
Tighten to
25 Nm (18 lbf/ft).
10.Refit flywheel.See Flywheel

ENGINE
17
REPAIR 11.Refit clutch.
See CLUTCH, Repair, Clutch
assembly
12.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 gearbox
13.Reconnect battery.
CRANKSHAFT BEARING BUSH
Service repair no - 12.21.45
Remove
1.Disconnect battery.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
assembly
4.Remove flywheel.See Flywheel
5.Remove bearing bush.
NOTE: The bearing bush can be removed
by using one of the following methods.
Method 1.
Obtain a short length of steel rod of a diameter having
a good slide fit in the bore of the bush. Pack the bore
with grease and insert the steel rod into the end of the
bore, give a sharp blow with a hammer and the
grease should drive out the bush. It is recommended
that the bush and rod be covered by a suitable cloth
or rag to prevent grease from splashing.Method 2.
Thread the bore of the existing bush and using a
suitable bolt extract the bush. Thoroughly clean bush
location ensuring all swarf is removed.
Refit
1.Fit new bush using a suitable shouldered drift,
inserting bush flush with end of crankshaft.
2.Refit flywheel.
See Flywheel
3.Refit clutch.See CLUTCH, Repair, Clutch
assembly
4.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 gearbox
5.Reconnect battery.

12ENGINE
18
REPAIR FLYWHEEL HOUSING
Service repair no - 12.53.01
Remove
1.Disconnect battery.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
assembly
4.Remove flywheel.See Flywheel
5.Remove 3 fixings and withdraw starter motor.
6.Remove 2 bolts from top of flywheel housing.
7.Remove 4 bolts securing bottom of flywheel
housing to engine mounting brackets.
8.Remove inner bolts and lift off flywheel housing.Refit
9.Clean rear face of housing and mating face on
block, ensuring all old sealant is removed.
10.Apply sealant to flywheel housing mating face on
cylinder block.
11.Fit housing to cylinder block. Tighten retaining
bolts to
45 Nm (33 lbf/ft).
12.Remove surplus sealant from block.
13.Fit starter motor.
14.Fit flywheel.
See Flywheel
15.Fit clutch.See CLUTCH, Repair, Clutch
assembly
16.Fit gearbox.See MANUAL GEARBOX, Repair,
R380 gearbox
17.Reconnect battery.