1996 LAND ROVER DEFENDER engine oil

12ENGINE
24
REPAIR Refit
8.Fit oil pump rotors in front cover.
9.Apply a bead of RTV sealant around retaining
plate.
10.Fit oil pump retaining plate to front cover,
securely tighten screws.
11.Fit front cover to cylinder block.
See Front
cover gasket
OIL PRESSURE RELIEF VALVE
Service repair no - 12.60.56
Remove
1.Remove engine oil sump.
See Engine oil
sump
2.Unscrew relief valve retaining plug from base of
front cover.
3.Withdraw valve spring and plunger and check for
wear.
Valve spring free length, 68.00 mm (2.68 in).
NOTE: If the valve plunger sleeve is badly
worn, pitted or scored, a new front cover
must be fitted.
See Front cover gasket
Always renew valve spring and plunger as a pair.
Refit
4.Insert valve plunger and spring into sleeve in
front cover and secure with retaining plug.
5.Fit engine oil sump.
See Engine oil sump

ENGINE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Starter motor (bolt and nut) 45........................................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................
Generator to auxiliaries mounting bracket 25.................................................
Tachometer electrical connection 4...............................................................

FUEL SYSTEM
3
ADJUSTMENT INJECTION PUMP TIMING - CHECK AND ADJUST
Service repair no - 19.30.01
1.Viewing the valve mechanism through oil filler
aperture, turn crankshaft clockwise until inlet
valve of No.1 cylinder has just closed. No.1
cylinder is now just before TDC.
2.Remove blanking plug from flywheel housing
and insert timing toolLRT-12-044, locating
centre pin on flywheel.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
adjustments or remove and refit procedures are
required, it may be necessary to remove the
undertray and/or integral access panels.
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
3.Cearfully rotate crankshaft clockwise until centre
pin engages timing slot in flywheel.
4.Remove injection pump access plate, complete
with gasket, from front cover plate.
5.Fit locking pinLRT-12-045/2to injection pump
gear. If difficulty is experienced in inserting pin,
adjustments will be needed to correctly set
injection pump timing as follows:
6.Support injection pump retaining nut to prevent
strain on timing belt.
7.Slacken the 3 keeper plate retaining bolts.
8.Carefully turn fixing nut and keeper plate until
locking pin can be inserted, without restriction,
into injection pump gear.
9.Tighten keeper plate bolts to
25 Nm (18 lbf/ft)
and remove locking pin.
10.Refit injection pump access plate plate and
gasket.
11.Remove flywheel timing tool and refit blanking
plug.
12.Run engine until normal operating temperature is
reached and check that idle speed adjustment,
See low and high idle speed adjustmentand
throttle cable adjustment
See Throttle cable
are correct.

FUEL SYSTEM
3
REPAIR FUEL INJECTORS
Service repair no - 19.60.10
Remove
NOTE: When a fuel injector is considered
to be the cause of irregular running and
loss of power it will be necessary to fit a
donor set of injectors to determine which injector
is at fault. DO NOT attempt to dismantle or carry
out spray tests on the fuel injectors. This work
can only carried out by authorised Bosch dealers.
1.Remove oil filler cap and release sound
insulation cover from top of engine.
2.Disconnect high pressure fuel supply pipes from
injectors and injection pump. Remove in pairs.
3.Disconnect spill return hose(s) from injectors.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foriegn matter.5.Remove retaining nut and release each injector
clamp plate from cylinder head.
6.Remove injector and discard copper washer.
Refit
7.Ensure injectors and seating in cylinder head are
clean.
8.Lightly grease a new copper sealing washer and
position on each injector.
9.Fit injectors in cylinder head with spill return
outlets facing outward.
10.Secure injector with clamp plate and nut. Tighten
nut to
25 Nm (18 lbf/ft).
NOTE: The clamp plates are slightly
curved and should be fitted with the
convex side uppermost.
11.Fit the spill return pipe with a single copper
washer under the head of the banjo bolt and 2
copper washers fitted between the injector and
the banjo. Tighten banjo bolt to
10 Nm (7 lbf/ft).
12.Fit high pressure pipes to injectors and injection
pump. Tighten union nuts to
28 Nm (21 lbf/ft).
13.Fit sound insulation cover and oil filler cap.

FUEL SYSTEM
11
REPAIR HEATER PLUGS
Service repair no - 19.60.31
Remove
1.Disconnect battery.
No.1 heater plug - air conditioning models:
2.Release drive belt from compressor pulley.See
AIR CONDITIONING, Repair, Compressor
drive belt
3.Remove 4 bolts securing compressor to front
cover, move compressor aside.
No.3 heater plug:
4.Remove retaining bolt and withdraw breather
valve from rocker cover. Remove and discard 'O'
ring.
All heater plugs:
5.Remove terminal nut and disconnect wire from
heater plug terminal.
6.Unscrew heater plug.
Refit
7.Clean heater plug and seating.
8.Coat threads of heater plug with suitable
anti-seize compound operational to a
temperature of 1000°C.
9.Fit heater plug, tighten to
23 Nm (17 lbf/ft).
10.Connect wire to heater plug terminal and secure
with nut.
NOTE: Feed wire must be connected to
No. 4 heater plug terminal.
No. 3 heater plug:
11.Lubricate new 'O' ring with engine oil and fit to
breather valve.
12.Fit valve to rocker cover, tighten to bolt to
15 Nm
(11 lbf/ft).
No. 1 heater plug - air conditioning models
13.Position compressor to front cover, fit bolts and
tighten to
25 Nm (18 lbf/ft).
14.Fit drive belt to compressor pulley and adjust
tension.
See AIR CONDITIONING, Repair,
Compressor drive belt
All models:
15.Reconnect battery.

19FUEL SYSTEM
14
REPAIR TURBOCHARGER INLET HOSE
Service repair no - 19.42.11
Remove
1.Disconnect battery.
2.Slacken retaining clip and disconnect intake
hose from turbocharger.
3.Slacken retaining clip and disconnect hose from
air cleaner.
4.If fitted, disconnect EGR modulator valve
vacuum spill pipe from inlet hose.
5.Slacken retaining clip and disconnect breather
valve hose from inlet hose.
6.Remove inlet hose.
Refit
7.Fit inlet hose to air cleaner.
8.Fit cyclone breather hose to inlet hose.
9.If applicable, fit vacuum spill pipe to inlet hose.
10.Fit inlet hose to turbocharger.
11.Reconnect battery.TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Remove banjo bolt securing oil feed pipe to
turbocharger and discard 2 joint sealing
washers.
4.Unscrew union and remove feed pipe from
cylinder block.
5.Plug connections to prevent ingress of dirt.
Refit
6.Using new joint washer, fit oil feed pipe to
cylinder block. Tighten union connector to
25
Nm (18 lbf/ft).
7.Fit a new joint washer to both sides of banjo and
secure feed pipe to turbocharger. Tighten banjo
bolt to
20 Nm (15 lbf/ft).
8.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
9.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
10.Reconnect battery.

FUEL SYSTEM
15
REPAIR TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Unscrew union and disconnect oil drain pipe
from cylinder block.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove drain pipe and discard gasket.
6.Plug connections to prevent ingress of dirt.
Refit
7.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
8.Using new gasket, fit oil drain pipe to
turbocharger. Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit drain pipe to cylinder block and tighten union
connector to
38 Nm (28 lbf/ft).
10.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
11.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
12.Reconnect battery.