1996 LAND ROVER DEFENDER service

70BRAKES
2
REPAIR BRAKE SYSTEM BLEED
Service repair no - 70.25.02
Preparation
WARNING: Before bleeding the brake
system refer to general brake service
practice.
See General Brake Service
Practice
.
·During bleed procedure, brake fluid level must
not be allowed to fall below the MIN level.
·To bleed the hydraulic circuits, four bleed
nipples are provided, one at each caliper.
·There are two methods by which air can be
removed from the braking system:-
1. MANUAL BLEED PROCEDURE.
2. PRESSURE BLEED PROCEDURE.
Pressure bleed procedure
Purpose designed equipment for pressure filling and
bleeding of hydraulic systems may be used on Land
Rover vehicles. The equipment manufacturer's
instructions must be followed and the pressure must
not exceed 4.5 bar, 65 lb/in
2.
Manual bleed procedure
Equipment required
·Clean glass receptacle
·Bleed hose
·Wrench
·Approx 2 litres (3 pints) brake fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
Master cylinder bleed
1.Disconnect battery.
2.Depress brake pedal fully and slowly 5 times.
3.Release the pedal and wait for ten seconds.
4.Air bubbles will rise into the reservoir during
these instructions.
5.Repeat instructions until a firm resistance is felt
at the pedal.
Complete circuit bleed
1.Disconnect battery.
2.Bleed front calipers, driver's side first. Fit bleed
hose to bleed screw.
3.Dip free end of bleed hose into brake fluid in
bleed bottle.
4.Open bleed screw of caliper.
5.Depress brake pedal fully several times until fluid
is clear of air bubbles.
6.Keeping pedal fully depressed, tighten bleed
screw, then release pedal.
7.Repeat procedure on other front caliper followed
by rear calipers.
8.Fit all bleed screw protection caps.
9.Check/top-up fluid level when bleeding is
complete
See Fluid Level Check/Top-Up.

BRAKES
3
REPAIR MASTER CYLINDER
Service repair no - 70.30.08
Before starting repair refer to general brake service
practice
See General Brake Service Practice.
Remove
1.Disconnect battery.
2.Place a container under the master cylinder to
catch escaping brake fluid.
3.Clean area round master cylinder ports.
4.Disconnect pipes from master cylinder ports.
Cover, not plug, the pipe ends to prevent entry of
dirt.
5.Disconnect electrical leads from reservoir cap.
6.Remove two nuts securing master cylinder to
servo and withdraw cylinder.
7.Remove reservoir cap and drain fluid into
suitable container for disposal.
8.The reservoir is a push fit in the master cylinder
and secured by seals. Carefully ease the
reservoir from the master cylinder by rolling it
from the seals. Note that the two seals are
different sizes.
Refit
9.Insert new reservoir seals in the master cylinder
ports and fit reservoir to master cylinder.
10.Ensuring that water ingress seal is in position, fit
master cylinder to servo. Tighten fixings to
26
Nm (19 lbf/ft).
11.Connect brake pipes to master cylinder ports
and tighten to
15 Nm (11 lbf/ft).
12.Fit electrical leads to reservoir cap
13.Fill reservoir with recommended brake fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
14.Bleed the brake systemSee Brake system
bleed
.
15.Reconnect battery and road test vehicle.

70BRAKES
4
REPAIR PRESSURE REDUCING VALVE (PRV)
Service repair no - 70.25.21
Remove
1.Disconnect battery.
2.Clean area around reducing valve ports.
3.Place a container under valve to catch escaping
brake fluid.
4.Disconnect primary circuit pipe unions ñAñ
from valve.
5.Disconnect secondary circuit pipe unions ñBñ
from valve.
6.Cover pipes to prevent ingress of dirt.
7.Remove single retaining nut and bolt securing
valve to engine bulkhead.
8.Remove valve.
Refit
9.Fit valve to engine bulkhead. Tighten bolt to
15
Nm (11 lbf/ft).
10.Connect primary and secondary circuit pipes to
valve. Tighten to
16 Nm (12 lbf/ft).
11.Fill brake reservoir with recommended brake
fluid
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
.
12.Bleed the brake system
See Brake system
bleed
.
13.Reconnect battery and road test vehicle.SERVO NON RETURN VALVE
Service repair no - 70.50.15
Remove
1.Disconnect brake vacuum hose from servo non
return valve.
2.Carefully prise valve out with a screwdriver blade
between valve and grommet. Take care not to
exert too much pressure on the vacuum
chamber.
3.Remove rubber grommet but be careful not to
allow it to fall into the vacuum chamber.
4.Check the valve for correct operation; it should
not be possible to pass air through into the servo
in direction of arrow. Do not use compressed air.
Refit
5.Fit rubber grommet.
6.Smear ribs of the valve with Lucas Girling rubber
grease to assist assembly, and push valve fully
home.
7.Connect vacuum hose to the valve.
8.Road test vehicle.

BRAKES
5
REPAIR SERVO ASSEMBLY
Service repair no - 70.50.01
Remove
Before starting repair refer to general brake service
practice
See General Brake Service Practice.
NOTE: The non-return valve and grommet,
are the only serviceable components. In
event of failure or damage, fit a new unit.
1.Remove master cylinderSee Master cylinder.
2.Disconnect vacuum supply hose from servo unit.
3.At footwell, release 2 brake pedal return springs.
4.Disconnect leads from brake light switch at rear
of pedal box.
5.Remove blanking grommets from each side of
pedal box.
6.Remove split pin and clevis pin securing servo
push rod to brake pedal.
7.Remove 4 nuts and plain washers securing
servo to pedal box.
8.Remove servo assembly and rubber washer
from bulkhead.Refit
9.Locate servo assembly and rubber washer to
engine bulkhead and secure to pedal box.
Tighten fixings to
14 Nm (10 lbf/ft).
10.Fit brake pedal to servo push rod with clevis pin
and new split pin.
11.Fit blanking grommets to each side of pedal box.
12.At footwell, attach pedal return springs.
13.Connect vacuum hose to servo non-return valve.
14.Fit brake master cylinder to servo unit
See
Master cylinder
.

70BRAKES
6
REPAIR BRAKE PEDAL
Service repair no - 70.35.01 - Brake pedal
Service repair no - 70.35.03 - Pedal box
Remove
1.Remove brake servo assembly.
See Servo
assembly
.
2.Remove 6 bolts securing pedal box to engine
bulkhead.
3.Taking care not damage brake fluid pipes,
remove pedal box assembly and gasket.
4.Release return springs from pedal and pedal box
bosses.
5.Using a suitable punch, drift out retaining pin and
withdraw pedal pivot shaft.
6.Remove brake pedal complete with pivot
bushes.
7.Examine components for wear or damage,
renew as necessary.
8.If it is necessary to fit new pivot bushes, they
must be reamed out to 15,87 mm±0,02 mm
(0.625±0.001 in) after fitment.Refit
9.Lubricate pedal pivot shaft and bushes with
general purpose grease.
10.Fit pedal to pedal box, insert pivot shaft and
secure with new split pin.
11.Attach return springs to pedal and pedal box
bosses.
12.Fit pedal box and gasket to engine bulkhead.
Tighten fixings to
25 Nm (18 lbf/ft).
13.Fit brake servo assembly.See Servo
assembly
.

BRAKES
7
REPAIR REV: 05/99 FRONT BRAKE PADS - ALL MODELS
Service repair no - 70.40.02
Remove
1.Remove front road wheels .
2.Clean exterior of calipers.
3.Remove split pin from retaining pins.
4.Remove pad retaining pins and anti-rattle
springs.
5.Remove brake pads.
6.Clean exposed parts of pistons, using new brake
fluid. Wipe away excess with a lint free cloth.
7.Using piston clampLRT-70-500press each
piston back into its bore. Ensure that displaced
brake fluid does not overflow from reservoir.
Refit
8.Fit brake pads.
9.Fit pad retaining pins and anti-rattle springs.
Secure with new split pins.
10.Apply service brake pedal several times to locate
pads.
11.Fit road wheels. Tighten wheel nuts to correct
torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
12.Check fluid reservoir. Top up if necessary, using
correct grade of fluid
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
.

70BRAKES
8
REPAIRREV: 05/99 REAR BRAKE PADS
Service repair no - 70.40.03
Service tool:
Remove
1.Remove rear road wheels.
2.Clean exterior of calipers.
3.Remove pad retaining pins and anti-rattle
springs. Note differences between 90 and
110/130 models.
4.Remove brake pads.
5.Clean exposed parts of pistons, using new brake
fluid. Wipe away excess with a lint free cloth.
6.Using piston clampLRT-70-500press each
piston back into its bore. Ensure that displaced
brake fluid does not overflow from reservoir.
Refit
7.Insert brake pads.
8.Fit anti-rattle springs and secure with retaining
pins.
9.Apply service brake pedal several times to locate
pads.
10.Fit road wheels, remove chassis stands and
jack. Tighten wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
11.Check fluid reservoir, top up if necessary, using
correct grade of fluid
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
.
90 Models
110/130 Models

70BRAKES
10
REPAIR FRONT BRAKE CALIPERS
Service repair no - 70.55.05
Service repair no - 70.55.16
Before starting repair refer to general brake service
practice
See General Brake Service Practice.
Remove
1.Remove front road wheels.
2.Expose flexible brake hose by moving coiled
protective covering.
3.Using a recognised hose clamp, clamp hose to
prevent loss of brake fluid.
4.Disconnect rigid brake pipe from flexible hose,
seal exposed ends to prevent ingress of dirt.
5.Remove split pin, retaining pins and springs,
withdraw pads. If refitting pads, identify them for
assembly to original locations.
6.Remove 2 bolts and withdraw caliper from swivel
housing.
WARNING: Do not separate caliper halves
7.Clean outer surfaces of caliper using aerosol
brake cleaner.
8.Using special toolLRT-70-500, clamp pistons in
inboard half of caliper. Gently, keeping fingers
clear, and withCAUTION, apply air pressure to
fluid inlet port to expel pistons. It is unlikely that
pistons will expel at same time, regulate rate
with a suitable piece of wood between
appropriate piston and caliper.
9.Finally remove pistons, identifying them with
their respective bores.
10.Remove wiper seal retainer by inserting a blunt
screwdriver between retainer and seal. Pry
retainer carefully from mouth of bore.
11.Taking care not to damage seal grooves, extract
wiper seal and fluid seal.
12.Clean bores, pistons and seal grooves using
clean brake fluid only. If caliper or pistons are
corroded, or their condition is not perfect, new
parts must be fitted.