1996 LAND ROVER DEFENDER service

BRAKES
11
REPAIR REV: 05/99 Assemble outboard pistons
13.Coat new fluid seal with brake fluid. Ease seal
into groove in bore using only fingers, ensuring it
is properly seated. Fluid seal and groove are not
same in section, so when seal is seated it feels
raised to touch at edge furthest away from
mouth of bore.
14.Coat appropriate piston with brake fluid. Insert it
squarely into bore by hand only. Do not tilt piston
during insertion, leave approximately 8mm
projecting from bore.
15.Coat new wiper seal with brake fluid and fit to
new seal retainer. Slide assembly, seal first, over
protruding piston and into bore recess. Use
piston clamp to press home seal retainer and
piston.
Mounting inboard pistons
16.Clamp outboard pistons and carry out same
procedure for removing and fitting outboard
pistons and seals, instructions 8 to 15.
Fit calipers and pads
17.Fit caliper, tighten bolts evenly to
82 Nm (60
lbf/ft).
18.Connect brake flexible hoses to caliper. Tighten
to
15 Nm (11 lbf/ft).
19.Remove hose clamps.
20.Insert pads. Fit pins and springs, secure using
new split pin.
21.Bleed brake system
See Brake System Bleed
.
22.Press brake pedal firmly several times to locate
friction pads.
23.Fit road wheels, remove axle stands. Finally
tighten road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
24.Road test vehicle. Note that new friction pads
require 'bedding-in', this may take several
hundred miles before brakes are at maximum
efficiency.FRONT BRAKE DISCS
Service repair no - 70.10.10.
Remove
1.Remove hub assembly
See FRONT AXLE AND
FINAL DRIVE, Repair, Front hub assembly
.
2.Remove 5 hub to disc bolts.
3.Tap disc to separate from hub.
NOTE: On 110/130 vehicles ventilated
discs are fitted as standard.
Refit
4.Locate disc to hub.
5.Apply Loctite 270 to disc bolts and tighten to
73
Nm (54 lbf/ft).
6.Check total disc runout with a dial indicator, this
must not exceed 0,15 mm, 0.006 in. If necessary
reposition disc.
7.Fit hub assembly
See FRONT AXLE AND
FINAL DRIVE, Repair, Front hub assembly
.
Disc reclamation
8.Check disc thickness. This dimension may be
machined to minimum thickness of 12 mm (0.47
in.) - solid discs, 22 mm (0.90 in) - ventilated
discs. Machine equal amount off each face.
NOTE: The disc MUST BE renewed if the
minimum running thickness stamped on
the disc is recorded.

BRAKES
13
REPAIR REAR BRAKE CALIPERS
Service repair no - 70.55.06
Service repair no - 70.55.17
Before starting repair refer to General brake service
practice
See General Brake Service Practice.
Remove caliper
1.Remove rear road wheels.
2.Using a recognised hose clamp, clamp flexible
brake hose above rear axle.
90 Models
110/130 Models
3.Remove brake pipe from rear brake caliper.4.Seal pipe ends to prevent ingress of dirt.
5.Remove retaining pins and springs and withdraw
pads. If same pads are to be refitted, identify
them for assembly in original positions.
6.Remove 2 bolts and withdraw caliper from rear
axle.
Repair
WARNING: Do not separate caliper halves.
7.Clean outer surfaces of caliper with aerosol
brake cleaner.
8. WITH CAUTIONexpel pistons from their bores
by applying air pressure to fluid inlet port. It is
unlikely both pistons will expel at same time,
regulate rate with a suitable piece of wood
inserted between two pistons.
9.Finally, remove pistons keeping them identified
with their respective bores.
10.Remove wiper seal retainer by inserting a blunt
screwdriver between retainer and seal and pry
retainer carefully from mouth of bore.
11.Taking care not to damage seal grooves, extract
wiper seal and fluid seal.
12.Clean bores, pistons and particularly seal
grooves using clean brake fluid only. If caliper or
pistons are corroded or their condition is not
perfect new parts must be fitted.
13.Apply brake fluid to new seal. Fit seal into
groove in bore. When seal is seated it feels
raised to touch at edge furthest away from
mouth of bore.
14.Coat piston with brake fluid. Insert it squarely
into bore. Do not tilt piston during insertion and
leave 8mm projecting from bore.

70BRAKES
14
REPAIRREV: 05/99 15.Coat a new wiper seal with brake fluid and fit to
new seal retainer. Slide assembly, seal first, over
protruding piston into bore recess.
16.Using special toolLRT-70-500- piston clamp,
press home seal retainer and piston.
Mounting inboard piston
17.Carry out same procedure as for removing and
fitting outboard piston and seals, instructions 8 to
16.
Fit calipers and pads to vehicle
18.Fit caliper to axle, tighten 2 bolts evenly to
82
Nm (60 lbf/ft).
19.Connect brake pipe to caliper. Tighten to15 Nm
(11 lbf/ft).
20.Remove clamp from flexible brake hose.
21.Insert pads and retaining springs, secure in
position with new retaining pins and spread ends
or fit new split pins, depending on vehicle model.
Note correct position of retaining springs on 90
models.
22.Bleed brake system
See Brake System Bleed.
23.Press brake pedal firmly several times to locate
pads.
24.Fit road wheels, remove axle stands. Finally
tighten road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
25.Road test vehicle. Note new brake pads require
'bedding-in', for several hundred miles before
brakes are at maximum efficiency.REAR BRAKE DISC
Service repair no - 70.10.11.
Remove
1.Remove rear hub assembly
See REAR AXLE
AND FINAL DRIVE, Repair, Rear hub
assembly
.
2.Remove disc bolts.
3.Remove disc from rear hub.
Refit
4.Fit disc to rear hub.
5.Fit disc bolts. Tighten to
73 Nm (54 lbf/ft).
6.Check total disc run out, this must not exceed
0,15 mm (0.006 in). If necessary reposition disc.
7.Fit rear hub assembly
See REAR AXLE AND
FINAL DRIVE, Repair, Rear Hub Assembly
.
Disc reclamation
8.Check disc thickness. This dimension may be
machined to minimum thickness of 12 mm.
Machine equal amounts off each face.
NOTE: The brake disc MUST BE renewed if
the minimum running thickness stamped
on the disc is recorded.

70BRAKES
16
REPAIRREV: 05/99 TRANSMISSION BRAKE SHOES
Service repair no - 70.45.18
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on a ramp.
2.Disconnect rear propeller shaft from
transmission output flange at brake drum.
3.Slacken off transmission brake drum adjustment
bolt.
4.Remove single screw securing brake drum to
output flange.
5.Withdraw drum to expose brake assembly.
6.Release top and bottom springs from brake
shoes, see J6337.
7.Grip dished washer with a pair of pliers, depress
washer and turn through 90°.
8.Remove dished washer, complete with hold
down spring and pin from both shoes.
9.Move brake shoes out from adjuster slides,
release from abutment plate and remove from
backplate.
10.Check that springs are satisfactory for continued
use. If new brake shoes are to be fitted, the
srings should also be renewed.Refit
11.Locate RH brake shoe in slide and secure brake
shoe and lever assembly to backplate with hold
down pin, spring and dished washer.
12.Locate LH brake shoe in slide and fit abutment
plate between both brake shoes. Secure LH
shoe with hold down pin, spring and dished
washer.
13.Fit pull-off springs to brake shoes.
14.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
15.Check that hand brake lever is released.
16.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
17.Tighten adjuster bolt to
25 Nm (18 lbf/ft)to
ensure brake drum is locked.
18.Slacken off adjuster bolt by 1.5 turns to give
shoes a running clearance. Check that the drum
is free to rotate.
19.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
20.Remove wheel chocks and check operation of
handbrake.

BRAKES
17
REPAIR HANDBRAKE CABLE
Service repair no - 70.35.25
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on ramp.
2.Remove 3 trim studs and lift up handbrake
gaiter.
3.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever.
4.Slacken off transmission brake drum adjusting
screw.
5.Disconnect propeller shaft from output flange.
6.Remove retaining screw and withdraw brake
drum.
7.Release handbrake cable clevis from abutment
on cable lever, see J6337, and pull through
aperture in back plate.
8.Pull cable from heelboard and remove from
vehicle.
Refit
9.Feed new cable through heelboard ensuring
rubber grommet is correctly located.
10.Position cable over guide plate, insert through
backplate and connect to cable lever.
11.Fit cable to handbrake lever and secure with
clevis pin and split pin.
12.Fit handbrake gaiter.
13.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
14.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
15.Tighten adjuster bolt further to
25 Nm (18 lbf/ft)
to ensure brake drum is locked.
16.Slacken off adjuster bolt by 1.5 turns to give
brake shoes running clearance. Check that the
drum is free to rotate.
17.Slacken locknut and adjust cable to give the
handbrake pawl two notches free movement on
the rachet before being fully operational on third
notch (brake shoes are fully expanded against
drum).
NOTE: Cable adjustment is for a new cable
or to compensate for cable stretch. Cable
adjustment must not be used to take up
brake shoe wear.
18.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
19.Remove wheel chocks and check operation of
handbrake.

70BRAKES
18
REPAIR VACUUM PUMP
Service repair no - 70.50.19
Remove
NOTE: To ease pump removal set engine
to T.D.C. on No.1 cylinder.
1.Disconnect battery.
2.Remove air cleaner
See FUEL SYSTEM,
Repair, Air cleaner
.
3.Detach servo hose from vacuum pump.
4.Remove bolt securing air cleaner support
bracket strut.
5.Remove 6 bolts securing vacuum pump.
6.Detach pump complete with strut and harness
bracket. Note location of strut and bracket for
Refit.
Refit
7.Clean mating faces of pump and block.
8.Loosely assemble pump to block with a new
gasket and with air cleaner strut and harness
bracket located under heads of bolts noted
during Remove.
9.Evenly tighten bolts, to depress pump plunger,
finally tightening to
25 Nm (18 lbf/ft).
10.Secure strut to air cleaner bracket.
11.Connect vacuum hose and secure with clip.
12.Refit air cleaner
See FUEL SYSTEM, Repair,
Air cleaner
.

70BRAKES
2
OVERHAUL MASTER CYLINDER
Service repair no - 70.30.09
Before starting overhaul procedure refer to general
brake service practice
See Repair, General brake
service practice
.
Dismantling master cylinder
1.Disconnect battery and remove master cylinder
from servo
See Repair, Master cylinder.
2.Before commencing overhaul procedure
thoroughly clean master cylinder and inspect
outer surfaces for damage and condition, renew
complete assembly if necessary.
3.The reservoir is a push fit in master cylinder and
secured by seals. Carefully ease reservoir from
master cylinder by rolling it from seals as
illustrated.
4.Using soft jaws, one either side of master
cylinder flange and clamp flange in a suitable
vice. Remove water ingress 'O' ring seal from
master cylinder to servo flange and discard.
5.Hold outside of transfer housing with a suitable
pair of grips, carefully pull, while working pliers in
a backwards and forwards rocking motion to
ease housing off master cylinder, discard
housing and vacuum seal.
6.Withdraw 2 reservoir seals from master cylinder
and note their positions in inlet ports for
reassembly. Discard both seals.
7.Remove retaining ring and 'O' ring seal from
machined outer surface of master cylinder,
discard both seal and retaining ring.

BRAKES
3
OVERHAUL
8.Remove guide ring from mouth of master
cylinder which supports primary plunger
assembly and place to one side, this component
is not part of master cylinder service kit and is to
be refitted on assembly of unit.
9.Pull primary plunger assembly out of master
cylinder.
NOTE: The primary plunger assembly
cannot be broken down any further and is
serviced as a complete unit. Discard
assembly.
10.The secondary plunger assembly will remain at
bottom of master cylinder bore, plunger can be
easily expelled by tapping assembly on a piece
of timber until plunger appears at cylinder mouth,
carefully pull plunger from master cylinder.
11.If swirl tube was not expelled at same time as
secondary plunger, repeat above operation to
expel it from bottom of master cylinder bore and
discard.12.Clean all parts with Girling cleaning fluid or
unused brake fluid and place cleaned parts on to
a clean sheet of paper. Inspect cylinder bore and
plungers for signs of corrosion, ridges and score
marks. Provided working surfaces are in perfect
condition, new seals from a Girling Service
repair kit may be used.
Renewing secondary plunger seals
A.Springs
B.Seal retainer
C.Recuperating seal (primary cup)
D.Washer
E.'L' seal
13.Remove components above from secondary
plunger and discard:
NOTE: A small screwdriver with end
rounded and polished is required to
remove 'L' seal. DO NOT damage
secondary plunger.
14.Coat new seals in unused brake fluid and firstly
fit 'L' seal to plunger.
15.Fit washer followed by recuperating seal. Fit seal
retainer and springs, ensure springs are
correctly seated.