1996 LAND ROVER DEFENDER rims

57STEERING
10
FAULT DIAGNOSISREV: 05/99 VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
.
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test
See Road Test Procedure
.
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks
See Visual
and Safety Checks
.
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock but not necessarily return
to exactly straight ahead without assistance from
the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure
See Stiff Steering Checklist.
If not, proceed with basic checks and adjustments
See Visual Check and Basic Adjustments.

STEERING
3
ADJUSTMENT FRONT WHEEL ALIGNMENT
Service repair no - 57.65.01
Checking Toe-out dimensions
NOTE: Recognised front wheel alignment
and tracking equipment should be used
for this operation. Only the use of basic
equipment is described below. No Adjustment is
provided for castor, camber or swivel pin
inclinations.
1.Set vehicle on level ground with road wheels
positioned straight ahead.
2.Push vehicle back and forwards to settle linkage.
3.Set up the equipment to manufacturers
instructions and check alignment as advised by
equipment supplier.
4.Position trammel probes on inner face of wheel,
not the rims, if the latter are damaged.
5.Measure toe-out at horizontal centre-line of
wheels.
6.Check tightness of clamp bolt fixings. Tighten to
14 Nm (10lbf/ft).
Adjust
7.Slacken clamps at both ends of track rod.
8.Rotate track rod to increase or decrease its
effective length until correct toe-out is obtained
See GENERAL SPECIFICATION DATA,
Information, Steering
.
9.Push vehicle rearwards turning steering wheel
from side to side to settle ball joints. With road
wheels set in straight ahead position, push
vehicle forward a short distance.
10.Recheck track and adjust if necessary.
11.When alignment is correct, tap ball joints in
direction of arrows to maximum of travel, to
ensure full unrestricted movement of track rod.
12.Tighten clamp bolts to
14 Nm (10 lbf/ft).
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.01
Adjust
NOTE: For details of drive belt adjust
procedure.
See ELECTRICAL, Repair,
Auxiliary Drive Belt

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification and model type, the
vehicle is equipped with pressed steel or alloy wheel
rims, both using tubeless radial ply tyres.
Tyre codes
The text, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications
See GENERAL SPECIFICATION
DATA, Information, Tyre size and pressures
.1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure secification -
(900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturers brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
3
REPAIR WHEEL BALANCING
CAUTION: It is essential that all wheel
balancing is carried out off the vehicle.
The use of on the vehicle balancing could
cause component damage or personal injury and
MUST NOT be attempted.
NOTE: Before attempting to balance a
wheel and tyre assembly clean all mud and
dirt deposits from both inside and outside
rims and remove existing balance weights.
Remove stones from the tyre tread in order to avoid
operator injury during dynamic balancing and to obtain
the correct balance.
Inspect tyres for damage and correct tyre pressures
and balance according to the equipment
manufacturer's instructions.
Steel wheels
Clean area of wheel rim and attach balance weights in
position shown.
Alloy wheels
Clean area of wheel rim and attach adhesive balance
weights in position shown. Cut through rear face of
weight strip to detach required weights.
CAUTION: Use only correct adhesive
balance weights to avoid damage to
aluminium wheel rim. DO NOT attempt to
use a steel wheel weight on an aluminium wheel.

76CHASSIS AND BODY
26
REPAIR FRONT HEADLINING - 90 STATION WAGON
Service repair no - 76.64.10
Remove
1.Remove sun roof headlining finisher.
2.Remove sun visors
See Sun visors.
3.Remove interior lamp
See ELECTRICAL,
Repair, Interior lamp
.
4.Remove interior mirror and mounting plate
See
Interior mirror
.
5.Remove 4 retaining screws and detach both 'A'
post trims.
6.Remove caps and unscrew front seat belt fixing
bolts from 'B' posts.7.Carefully prise side trim panel cap fastener from
'B' posts.
8.Carefully prise 2 cap fasteners, from both sides,
securing headlining to body at door aperture.
9.Carefully prise out 5 cap fasteners securing front
and rear headlinings to roof.
10.From both sides, pull side trim panel inwards
enough to release rear corners of front
headlining.
11.Lower headlining and remove from vehicle.NOTE: Take care not to bend the
headlining on removal and refitting.
Refit
12.With assistance, raise headlining to roof.
13.Carefully pull side trim panel inwards, on both
sides, and slide headlining behind trim panel.
14.Position front headlining into recess of rear
headlining and secure both to roof mounting
brackets with 5 cap fasteners.
15.Secure both sides of front headlining to body at
door apertures with cap fasteners.16.Fit side cap fasteners at 'B' posts.
17.Secure seat belts to 'B' posts and tighten bolts to
32 Nm (24 lbf/ft).Fit caps to bolts.
18.Fit 'A' post trims.
19.Fit interior mirror
See Interior mirror.
20.Fit interior lamp
See ELECTRICAL, Repair,
Interior lamp
.
21.Fit sun visors
See Sun visors.
22.Fit sun roof headlining finisher.