1996 LAND ROVER DEFENDER tyre pressure

GENERAL SPECIFICATION DATA
11
INFORMATION REV: 05/99 TYRE SIZE AND PRESSURES
90 models Front Rear
Normal - all load conditions
205 R16 radial
& 265/75 R16 (multi-terrain)1,9 bar .................................. 2,4 bar
28 Ibf/in
235 Ibf/in2
2,0 kgf/cm22,5 kgf/cm2
750 R16 radial1,9 bar ........................................................ 2,75 bar
28 Ibf/in240 Ibf/in2
2,0 kgf/cm22,8 kgf/cm2
110 models
Normal - all load conditions
750 R16 Radial1,9 bar ....................................................... 3,3 bar
28 Ibf/in
248 Ibf/in2
2,0 kgf/cm23,4 kgf/cm2
130 models
Normal - all load conditions
750 R16 Radial3,0 bar ....................................................... 4,5 bar
44 Ibf/in
265 Ibf/in2
3,1 kgf/cm24,6 kgf/cm2
WARNING: Tyre pressures must be
checked with the tyres cold, as the
pressure is about 0,21 bar (3 Ibf/in
2, 0,2
kgf/cm2) higher at running temperature. If the
vehicle has been parked in the sun or high
ambient temperatures, DO NOT reduce the tyre
pressures, move the vehicle into the shade and
wait for the tyres to cool before checking the
pressures.
WHEELS
90 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
Alloy wheel size 7J X 16................................................................
110 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
130 models
Steel wheel size:
Heavy duty - UK and Western Europe 6.5F X 16.............................
Other markets 5.5F X 16..................................................................
WARNING: Always use the same make and
type of radial-ply tyres, front and rear. DO
NOT use cross-ply tyres, or interchange
tyres from front to rear.
·If the the wheel is marked 'TUBED', an inner
tube MUST be fitted, even with a tubeless tyre.
·If the wheel is marked 'TUBELESS', an inner
tube must NOT be fitted.

10MAINTENANCE
2
MAINTENANCE BATTERY CONNECTIONS
NOTE: The vehicle may be fitted with an
alarm and immobilisation system using a
battery backed-up alarm sounder.
See
ELECTRICAL, Repair, Battery
Disconnect battery leads, clean and grease with
petroleum jelly, including battery terminals.
CHECK OPERATION OF DOOR SWITCHES
When a Vehicle Immobilisation and Alarm System is
fitted it is important that all door and bonnet switches
operate correctly, otherwise perimeter and interior
protection may not function if a door or the bonnet is
opened.VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp alignment.
CHECK ROAD WHEELS AND TYRES
Check road wheels for damage.
Check tyres, including spare, for compliance with
manufacture's specificaton.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth.
See INTRODUCTION,
Information, wheels and tyres
Check/adjust tyre pressures.See WHEELS AND
TYRES, Repair, Tyres pressures
INSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION OF DISCS
Check thickness of brake pads, and renew if thickness
is less than 3,00 mm (0.12 in). Check brake pads for
oil contamination and fit a new set, if necessary,
See
BRAKES, Repair, front brake pads
orSee
BRAKES, Repair, rear brake pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to carry
out this operation.
See STEERING, Adjustment,
front wheel alignment
CHECK OPERATION OF ALL DOORS/TAILGATE,
BONNET AND LOCKS
LUBRICATE ALL DOOR/TAILGATE HINGES, AND
DOOR CHECK/LOCK MECHANISMS

10MAINTENANCE
14
MAINTENANCEREV: 05/99 ADDITIONAL MAINTENANCE SCHEDULES
Camshaft drive belt
The engine timing gears are driven by a toothed
rubber belt which must be renewed at intervals
determined by the severity of operating conditions. In
reasonable, temperate climate operation, the belt
should be renewed every 120,000 km (72,000 miles)
or every six years whichever occurs earlier.
In adverse operating conditions, such as work in dusty
atmospheres, high ambient temperatures, desert and
tropical zones, renew the belt every 60,000 km
(36,000 miles) or every three years, whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious engine damage.
Oil change diesel engines
If the vehicle is operated on fuel with a high sulphur
content (over 1%) the oil change intervals must not
exceed 5000 km (3000 miles).
Anti-freeze
At two yearly intervals or at the onset of the second
winter, the cooling system should be drained, flushed
and refilled with the required water and anti-freeze
solution.
Hydraulic brake fluid.
It is recommended that at 40,000 km (24,000 miles)
intervals or every two years, whichever is the earlier,
the hydraulic brake fluid should be completely
renewed.
At 80,000 km (48,000 miles) intervals or every four
years, whichever is the earlier, all hydraulic brake fluid
seals and flexible hoses should be renewed. All
working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.Air cleaner
When the vehicle is used in dusty or field conditions or
deep wading, frequent attention to the air cleaner may
be required.
Dampers
At 60,000 km (36,000 miles) intervals remove all
suspension dampers, test for correct operation, refit or
renew as necessary.
SPECIAL OPERATING CONDITIONS
When the vehicle is operated in extremely arduous
conditions or on dusty, wet or muddy terrain, more
frequent attention should be paid to all servicing
requirements.
Additional daily or weekly attention depending on
operating conditions:
Check/top-up transfer box oil.
Check steering rubber boots for security and
condition. Renew if damaged.
Check brake fluid level: Investigate cause if any fluid
loss is suspected.
Clean brake discs and calipers.
Lubricate front and rear propeller shaft
universal/sliding joints. Under tropical or severe
conditions, particularly where sand is encountered,
the sliding joints must be lubricated very frequently to
prevent ingress of abrasive material.
Every week and every maintenance inspection check
tyre pressures and inspect tyre treads and side walls.
Under arduous cross-country conditions the tyre
pressures should be checked much more frequently,
even to the extent of a daily check.
Monthly
Renew gearbox oil.
Renew transfer box oil.
Check air cleaner element and renew every 6 months
or as necessary.

MAINTENANCE
15
MAINTENANCE ADDITIONAL MAINTENANCE SCHEDULES
Camshaft drive belt
The engine timing gears are driven by a toothed
rubber belt which must be renewed at intervals
determined by the severity of operating conditions. In
reasonable, temperate climate operation, the belt
should be renewed every 120,000 km (72,000 miles)
or every six years whichever occurs earlier.
In adverse operating conditions, such as work in dusty
atmospheres, high ambient temperatures, desert and
tropical zones, renew the belt every 60,000 km
(36,000 miles) or every three years, whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious engine damage.
Oil change diesel engines
If the vehicle is operated on fuel with a high sulpher
content (over 1%) the oil change intervals must not
exceed 5000 km (3000 miles).
Anti-freeze
At two yearly intervals or at the onset of the second
winter, the cooling system should be drained, flushed
and refilled with the required water and anti-freeze
solution.
Hydraulic brake fluid.
It is recommended that at 40,000 km (24,000 miles)
intervals or every two years, whichever is the earlier,
the hydraulic brake fluid should be completely
renewed.
At 80,000 km (48,000 miles) intervals or every four
years, whichever is the earlier, all hydraulic brake fluid
seals and flexible hoses should be renewed. All
working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.Air cleaner
When the vehicle is used in dusty or field conditions or
deep wading, frequent attention to the air cleaner may
be required.
Dampers
At 60,000 km (36,000 miles) intervals remove all
suspension dampers, test for correct operation, refit or
renew as necessary.
SPECIAL OPERATING CONDITIONS
When the vehicle is operated in extremely arduous
conditions or on dusty, wet or muddy terrain, more
frequent attention should be paid to all servicing
requirements.
Additional daily or weekly attention depending on
operating conditions:
Check/top-up transfer box oil.
Check steering rubber boots for security and
condition. Renew if damaged.
Check brake fluid level: Investigate cause if any fluid
loss is suspected.
Clean brake discs and calipers.
Lubricate front and rear propeller shaft
universal/sliding joints. Under tropical or severe
conditions, particularly where sand is encountered,
the sliding joints must be lubricated very frequently to
prevent ingress of abrasive material.
Every week and every maintenance inspection check
tyre pressures and inspect tyre treads and side walls.
Under arduous cross-country conditions the tyre
pressures should be checked much more frequently,
even to the extent of a daily check.
Monthly
Renew gearbox oil.
Renew transfer box oil.
Check air cleaner element and renew every 6 months
or as necessary.

57STEERING
4
FAULT DIAGNOSIS Symptom:-
Fluid leaks from steering box seals.
CAUTION: The steering wheel must not be
held on full lock for more than 30 seconds
in one minute, as this may overheat the
fluid and cause damage to the oil seals.
1.Check fluid level
See Repair, Power Steering
Fluid Reservoir
.
Check fluid pressure
See Power Steering
System - Test
.
2.Is pressure high?
YES - Renew pump
See Repair, Power
steering Pump
.
If oil seal leaks persist after renewing the pump
See Overhaul, Power Steering Box.
NO -
See Overhaul, Power Steering Box.
Symptom:-
Insufficient power assistance - castor return
action normal.
1.Are tyres correct type and pressure?
NO -
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
.
YES - Continue.
2.Is fluid level correct?
NO - Check fluid level
See Repair, Power
Steering Fluid Reservoir
.
YES - Check system for air locks
See Repair,
Power Steering System - Bleed
.
3.Is pressure correct?
NO - Check fluid pressure
See Power Steering
System - Test
.
If pressure is not correct after bleeding the
system, renew pump
See Repair, Power
Steering Pump
.
YES -
See Overhaul, Power Steering Box.Symptom:-
Steering heavy - stiff, poor castor return action.
1.Are tyres correct type and pressure?
NO -
See INTRODUCTION, Information,
Wheels and Tyres
.
YES - Check universal joints for seizure and
correct alignment
See Repair, Lower Steering
Shaft and Universal Joints
.
Check power steering box adjustments
See
Overhaul, Power Steering Box
.
2.Is the power assistance satisfactory?
NO - See fault symptomInsufficient
assistance, (castor return action normal).
YES - Disconnect drag link from drop arm and
check steering column and box for stiffness
See
Repair, Drag Link and Drag Link Ends
.
3.Is the steering stiff with the drag link
disconnected?
NO - Check steering ball joints for seizure and
axle swivels lubrication and resistance
See
Repair, Drag Link and Drag Link Ends
,See
FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing
.
YES - Disconnect the lower steering shaft and
check the column and box for stiffness
See
Repair, Lower Steering Shaft and Universal
Joints
.
4.Is the steering column stiff to turn when
disconnected from the box?
NO - Remove and overhaul box
See Overhaul,
Power Steering Box
.
YES - Adjust steering column
See Stiff
Steering Checklist
.

57STEERING
10
FAULT DIAGNOSISREV: 05/99 VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
.
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test
See Road Test Procedure
.
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks
See Visual
and Safety Checks
.
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock but not necessarily return
to exactly straight ahead without assistance from
the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure
See Stiff Steering Checklist.
If not, proceed with basic checks and adjustments
See Visual Check and Basic Adjustments.

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification and model type, the
vehicle is equipped with pressed steel or alloy wheel
rims, both using tubeless radial ply tyres.
Tyre codes
The text, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications
See GENERAL SPECIFICATION
DATA, Information, Tyre size and pressures
.1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure secification -
(900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturers brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
1
FAULT DIAGNOSIS TYRE WEAR CHART
FAULT CAUSE REMEDY
Rapid wear at Tyres under-inflated Inflate to correct pressure
shoulders Worn suspension components Replace worn components
i.e. ball joints, panhard
rod bushes, steering damper
Excessive cornering speeds
Rapid wear at
centreTyres over-inflated Inflate to correct pressure
of tread
Wear at one
shoulderTrack out of adjustment Adjust track to correct figure
Bent panhard rod Check and replace worn or damaged
components
Bald spots or tyre Wheel out of balance Balance wheel and tyre
cupping assembly
Excessive radial runout Check runout and replace tyre
if necessary
Shock absorber worn Replace shock absorber
Excessive braking
Tyre scalloped Track out of adjustment Adjust toe to correct figure
Worn suspension components Replace tyre as necessary
Excessive cornering speeds
CAUTION: This diagnosis chart is for general guidance only and does not necessarily include
every cause of abnormal tyre wear.