1996 GMC SAVANA Owners Manual

Windshield Wi
You control the windshield
wipers by turning the band
with the wiper symbol on
it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle.
If you want more cycles, hold the
band on MIST longer.
You can set the wiper speed for a long or short delay
between wipes. This can
be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer to
LOW, the shorter the delay. For steady wiping
at low speed,
turn the band to
the
LOW position. For high-speed wiping, turn the
band further,
to HIGH. To stop the wipers, move the
band to
OFF.
Remember that damaged wiper blades may prevent
you from seeing well enough
to drive safely. To
avoid damage, be sure to clear ice and snow from the
wiper blades before using them.
If they are frozen to
the windshield, carefully loosen or thaw them.
If
your blades do become damaged, get new blades or
blade inserts.
Heavy snow or ice can overload your wipers. The
windshield wiper motor
is protected from overload
by a circuit breaker and a fuse. If the motor overheats
due
to heavy snow, etc., the wiper will stop until the
motor cools. Although the circuit is protected from
electrical overload, overload due
to heavy snow, etc.
may cause wiper linkage damage. Always clear ice
and heavy snow from the windshield before using your
windshield wipers.
2-31
ProCarManuals.com

Windshield Washer
At the top of the lever, there’s a paddle with the word
PUSH on it. To spray washer fluid on the windshield,
push the paddle.
Washer fluid will spray as long
as you push the paddle.
When
you let go of the paddle, the wipers will continue
to wipe for approximately two more wipe cycles and
then either stop or return to the preset speed.
Driving without washer fluid can be dangerous.
A
bad mud splash can block your vision. You could hit
another vehicle or
go off the road. Check your washer
fluid level
often.
Cruise Control (Option)
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot
on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.
In freezing weather, don’t use your washer until
the windshield
is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise control can be dangerous where you
can’t drive safely at a steady speed.
So,
don’t use your cruise control on winding.
roads or in heavy traffic.
slippery roads. On such roads, fast changes in tire traction can cause needless wheel
spinning, and you could lose control. Don’t
use cruise control on slippery roads.
Cruise control can be dangerous on
2-32
ProCarManuals.com

Resuming a Set Speed
Setting Cruise Control
-
L
If you leave your cruise control switch on when
you’re not using cruise, you might hit
a button
and
go into cruise when you don’t want to. You
could be startled and even lose control. Keep the cruise control switch
OFF until you want to use it.
1. Move the cruise control switch to ON.
2. Get up to the speed you want.
3. Press in the SET button
at the end of the lever
and release
it.
4. Take your foot off the accelerator pedal. Suppose
you set your
cruise control at a desired speed
and
then you apply the brake. This, of course, shuts off
the cruise control. But you don’t need to reset
it.
Once you’re going about 25 mph (40 km/h) or more,
you can move the cruise control switch from
ON to
R/A (Resume/Accelerate) for about half
a second.
You’ll go right back up to your chosen speed and
stay there.
Remember,
if you hold the switch at R/A longer than
half
a second, the vehicle will keep going faster until
you release the switch or apply the brake. You could be
startled and even lose control.
So unless you want to go
faster, don’t hold the switch at R/A.
2-33
ProCarManuals.com

Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher speed.
Push the button at the end of the lever, then release
the button and the accelerator pedal.
You’ll now
cruise at the higher speed.
Move the cruise switch from ON to R/A. Hold it
there until you get up to the speed you want, and
then release the switch.
To increase your speed in
very small amounts, move the switch to R/A for less
than half a second. Each time
you do this, your
vehicle
will go about I mph (1.6 km/h) faster.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
Push in the button at the end of the lever until you
reach the lower speed
you want, then release it.
0 To slow down in very small amounts, push the
button for less than
half a second. Each time you do
this, you’ll
go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going
up steep hills, you may have to step on
the accelerator pedal to maintain yo~lr speed.
If the
steepness of the
hill causes the vehicle speed to drop
more than
I5 rnph (9.4 km/h) below the set speed, your
cruise control
will automatically disengage. When going
downhill, you may have
to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out
of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control
on
steep hills.
Ending Cruise Control
There are two ways to turn off the cruise control:
Step lightly on the brake pedal; or
0 Move the cruise switch to OFF.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
2-34
ProCarManuals.com

Your parking/headlamp switch is on the driver's
side of your instrument panel.
Your instrument panel dimmer wheel has two
detent positions. When
the wheel is turned to
full brightness, and then
into the first detent position, the radio display and
PRNDL display
will go to the day mode (full intensity).
This is known as "parade" mode. The rest
of the I/P
illumination will stay in the maximum dimming state
(full brightness dimming). Turning the wheel up one
more detent will activate the interior dome light circuit
(with slightly higher effort).
Rotate the switch knob clockwise to the parking lamp
symbol to turn on:
Parking Lamps
0 Sidemarker Lamps
0 Taillamps
0 License Plate Lamps
Instrument Panel Lights
0 Ashtray Lamp
0 Glove Box Lamp
2-35
ProCarManuals.com

Rotate the switch knob clockwise again to the master
lighting symbol to turn on all the lamps listed
as well as
the headlamps.
Rotate the switch counterclockwise to
OFF to turn off
your lamps.
Rotate the thumb wheel next to the switch knob up
to
adjust instrument panel lights. Rotate the thumb wheel up
to the first notch
to return the radio display and gearshift
indicator display to
full intensity when the headlamps or
parlung lamps are on.
Rotate the thumb wheel up to the second notch to
activate the interior dome lamps.
You can switch your headlamps from high to low beam
by pulling
on the turn signal/high beam lever.
A circuit breaker protects your headlamps. If you have
an electrical overload, your headlamps will flicker on
and off. Have your headlamp wiring checked right away
if this happens.
Headlamps On Reminder
A buzzer will sound when your headlamps are turned on
and your ignition is
in OFF, LOCK or ACCESSORY,
If you need to use your headlamps when the ignition
switch is in
OFF, LOCK or ACCESSORY, the buzzer
can be turned off by turning the thumb wheel next
to the
parking lamp/headlamp switch all the way down.
Daytime Running Lamps (If Equipped)
Daytime Running Lamps (DRL) can make it easier for
others to see the front
of your vehicle during the day.
DRL can be helpful
in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
The DRL system will make your headlamps
come on at
a reduced brightness when:
0 The ignition is on,
The headlamp switch is off and
0 The parking brake is released.
If your vehicle was first sold, when new,
in Canada,
your headlamps will come on at reduced brightness.
ProCarManuals.com

If your vehicle was first sold, when new, in the United
States, your vehicle may be equipped with DRL.
If your
vehicle has
DRL, you will see the the DRL indicator
light
on your instrument panel and your low-beam
headlamps will come
on at reduced brightness.
When the DRL are
on, only your headlamps will be on.
The taillamps, sidemarker and other lamps won’t be on.
Your instrument panel won’t be lit up either.
When it begins to get dark, your DRL indicator light
is a reminder to turn your headlamp switch on. The
other lamps that come on with your headlamps will also
come
on.
When you turn off the headlamp switch, the regular
lamps will
go off, and your headlamps will change to
the reduced brightness of DRL.
To idle your vehicle with the engine on and the DRL off,
set the parking brake. The DRL will stay
off until you
release
the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when
you need it.
)ome Lamps
The dome lamps will come on when you open the doors.
You can also turn the dome lamps on by rotating the
thumb wheel, located
next to the headlamp knob, all
the way up to the second notch. In this position, the
dome lamps will remain on whether the doors are
opened or closed.
You can use the dome
lamp button, located below the headlamp knob,
to set the dome lamps to
automatically come on
when the doors are open,
or to remain off.
To turn the lamps off, push the button once. With the
button
in this position, the dome lamps will remain off
when the doors are open. To return the lamps to
automatic operation, push the button again and return it
to the out position. With the button
in this position, the
dome lamps will come on when you open
the doors.
The delayed entry will allow
you to enter or exit your
vehicle with the lamps staying on for about
20 seconds,
after the door is closed or ignition
is cycled.
2-37
ProCarManuals.com

Reading Lamps (Option)
If your vehicle has reading lamps, press the button next
to the lamp to turn the lamp on.
Press the button again to turn the lamp off.
Underhood Reel Lamp (Option)
If you have an underhood reel lamp, it is located on the
passenger side
of the engine compartment. The lamp can
be switched on without unreeling the cord. Also, you
can use it as a flashlight.
2-38
ProCarManuals.com