1996 FORD RANGER brake

216
*
[DR38800(ALL)06/95]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift the
automatic transmission gearshift into 2 (Second) gear or 1 (Low).
*
[DR38925(ALL)08/95]
Servicing Your Vehicle If You Tow
*
[DR38950(ALL)08/93]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedule and Recordbooklet for additional
information.
[DR39000(ALL)08/95]
Trailer towing tips
*
[DR39100(ALL)11/89]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[DR39200(ALL)05/90]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[DR39300(ALL)11/89]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[DR39400(ALL)11/89]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[DR39500(ALL)05/95]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
217
*
[DR39600(ALL)11/89]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
[DR39750(ALL)01/95]
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in P (Park) to increase the
engine idle speed. This aids in engine cooling and air
conditioner efficiency. If the engine overheats, rotate the
function selector control knob to panel position to stop the
compressor and increase the engine speed for a short time.
*
[DR39800(R )05/90]
RWARNING
Do not tow a trailer when using a temporary spare tire.
*
[DR39900(ALL)05/90]
Vehicles with trailers should not be parked on a grade.
However, if you must park on a grade, place wheel chocks
under the trailer's wheels as follows:
*
[DR40000(ALL)05/95]
n
Apply the brake pedal and hold.
*
[DR40100(ALL)11/89]
n
Have another person place the wheel chocks under the
trailer wheels.
*
[DR40200(ALL)08/95]
n
With the chocks in place, release the brake pedal, making
sure the chocks are holding.
*
[DR40300(ALL)03/91]
n
For automatic transmissions Ð apply the parking brake by
pressing the service brake pedal down firmly with your right
foot while applying the parking brake pedal with your left
foot.
[DR40400(ALL)01/95]
n
For manual transmissions Ð apply the service brake and
shift into N (Neutral) while still maintaining pressure on the
service brake pedal. Set the parking brake fully.
*
[DR40500(ALL)12/91]
n
Shift an automatic transmission into Park (P). Put the
gearshift of a manual transmission in Reverse. If your vehicle
is equipped with four-wheel drive make sure the transfer
case is not in Neutral.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

218
*
[DR40600(ALL)01/93]
To start, after being parked on a grade:
*
[DR40700(ALL)05/95]
n
Apply the brake pedal and hold.
*
[DR40800(ALL)08/95]
n
Start the engine.
*
[DR40900(ALL)08/95]
n
Shift transmission into gear and release the parking brake.
*
[DR41000(ALL)08/95]
n
Release the brake pedal and move the vehicle uphill to free
the wheel chocks.
*
[DR41100(ALL)05/95]
n
Apply the brake pedal and hold while another person
retrieves the chocks.
[DR41235(ALL)02/92]
Suspension Modifications
[DR41250(ALL)03/91]
The suspension and steering systems on your vehicle have been
designed and tested to provide both safe, predictable
performance (whether loaded or empty) as well as durable load
carrying capability. Any modifications to the suspension or
steering systems can reduce your vehicle's performance
capability and adversely affect driver and passenger safety. Ford
recommends that you DO NOT make modifications such as
adding or removing parts (like lift kits, stabilizer bars or
snowplowing equipment) or by using replacement parts
non-equivalent to the original factory equipment.
%*
[DR41260(ALL)02/92]
Snowplowing
*
[DR41275(ALL)01/93]
RWARNING
Do not use this vehicle for snowplowing.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

220
*
[RE00950(ALL)06/95]
RWARNING
Do not push-start your vehicle. You could damage the
catalytic converter. For further information, seeJumper
Cablesin the Index.
*
[RE01000(ALL)05/95]
RWARNING
To avoid damage or injury, follow these directions in the
order they are given. If in doubt, call for road service.
*
[RE01100(ALL)03/95]
Preparing Your Vehicle
*
[RE01200(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01300(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01400(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01500(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE01600(ALL)02/95]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

Roadside Emergencies
223
*
[RE03400(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[RE03500(ALL)04/95]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge. Driveability may be deteriorated slightly until all drive
modes are ªrelearned.ºYou may need to use a battery charger
to fully recharge the battery.
*
[RE03550(R )01/95]
If you need to replace your battery, seeBatteryin theServicing
Your Rangerchapter.
%*
[RE03600(ALL)03/95]
Changing a Tire
*
[RE03700(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
%*
[RE03800(ALL)03/95]
The Conventional Spare Tire
*
[RE03900(R )01/95]
If you have the conventional spare tire, you can use it as a
spare or as a regular tire. This spare tire is identical to the other
tires that come with your vehicle, although the wheel may not
match.
*
[RE03930(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[RE04000(ALL)03/95]
The Temporary Spare Tire
*
[RE04100(ALL)03/95]
You may have a high pressure temporary spare tire. This spare
tire is smaller than a regular tire and is designed for emergency
use only. Use it only when you get a flat tire and replace it as
soon as you can. This spare tire is marked with the words
ªTEMPORARY USE ONLYº so that you can easily identify it.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

Roadside Emergencies
227
%*
[RE15200(ALL)03/95]
Preparing to Change the Tire
*
[RE15250(ALL)12/91]
NOTE: To lift your vehicle by other than the front or rear
jacking points, be sure to use only hoist adapters with
a wide contact surface.
*
[RE15300(ALL)03/91]1.
Make sure that your vehicle will not move or roll. If you
have an automatic transmission, put the gearshift in Park. If
you have a manual transmission, put the gearshift in
Reverse. Set the parking brake and block the wheel that is
diagonally opposite the tire that you are changing.
*
[RE15335(ALL)12/91]
NOTE: Make sure the ignition is in the OFF position.
*
[RE15350(R )06/94]
If you have a four-wheel drive vehicles with manual locking
hubs, put transfer case lever in 2H, 4H, or 4L.
*
[RE15390(ALL)05/95]
When one of the back wheels is off the ground, the transmission
alone will not prevent the vehicle from moving or slipping off
the jack, even if the vehicle is in P (Park) or 1 (First). To
prevent the vehicle from moving when you change a tire, be
sure the parking brake is set, then block the wheel (both
directions) that is diagonally opposite (other side and end of the
vehicle) to the tire that is being changed.
[RE15400(ALL)05/95]
RWARNING
If the vehicle slips off the jack, someone could be
seriously injured.
*
[RE15440(R )05/95]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[RE15550(ALL)03/95]2.
Get out the spare tire and jack.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

236
[RE27600(ALL)12/91]
Recreational Towing Ð All wheels on the ground
[RE27700(ALL)05/91]
Towing your vehicle can be successfully performed by following
the appropriate guidelines for the type of powertrain on the
vehicle to be towed. The following guidelines, by powertrain
combination, are designed to ensure that the transmission is not
damaged due to insufficient lubrication.
[RE27800(ALL)12/91]
4x2ÐAutomatictransmission
*
[RE27900(ALL)03/95]
n
Release the parking brake.
[RE28000(ALL)01/95]
n
Place transmission gearshift in N (neutral).
[RE28100(ALL)10/94]
n
Maximum speed is 35 mph (56 km/h).
[RE28200(ALL)10/94]
n
Maximum distance is 50 miles (80 km).
[RE28300(ALL)06/94]
If a distance of 50 miles (80 km) or speed of 35 mph (56 km/h)
will be exceeded, youmust:
[RE28400(ALL)05/91]
n
Disconnect the driveshaft at the rear differential and properly
support it under the vehicle.
[RE28500(ALL)01/95]
n
Mark the driveshaft and axle flanges to ensure proper
position when reconnecting the driveshaft. Refer to service
manual for proper driveshaft fastener torque specification.
(See theAccessorieschapter for information on ordering
service manuals.)
[RE28600(ALL)05/95]
RWARNING
When disconnecting/installing the driveshaft, the parking
brake must be set and the wheels blocked to ensure the
vehicle does not roll.
[RE28700(ALL)06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996

Roadside Emergencies
237
[RE28720(ALL)12/91]
4x2ÐManualtransmission
*
[RE28740(ALL)03/95]
n
Release the parking brake.
[RE28750(ALL)01/95]
n
Place the transmission gearshift in the neutral position.
[RE28770(ALL)12/91]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[RE28800(R )06/94]
4x4ÐManualshifttransfercase
*
[RE28900(R )03/95]
n
Release the parking brake.
[RE29000(R )01/95]
n
Place the transmission gearshift in the neutral position.
[RE29100(R )01/95]
n
Place the transfer case gearshift in the neutral position.
[RE29200(R )06/94]
n
Set the manual locking hubs in the FREE position.
[RE29300(R )06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[RE29400(R )06/94]
4 x 4 Electric shift transfer case
*
[RE29500(ALL)03/95]
n
Release the parking brake.
[RE29600(ALL)01/95]
n
Place the transmission gearshift in the neutral position.
[RE29700(R )06/94]
n
Ensure the transfer case is in 2H and the hubs are unlocked.
[RE29800(ALL)10/94]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[RE29850(ALL)10/92]
For automatic transmissions:
[RE29900(ALL)10/94]
n
Maximum speed is 35 mph (56 km/h).
[RE30000(ALL)10/94]
n
Maximum distance is 50 miles (80 km).
[RE30100(ALL)06/94]
If a distance of 50 miles (80 km) or speed of 35 mph (56 km/h)
will be exceeded, youmust:
[RE30200(R )06/94]
n
Remove the rear driveshaft.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996