1996 FORD AEROSTAR tow

16 [SR04375(ALL)08/95]All Two Passenger Bench or Bedseat
*
[SR04400(ALL)12/91]
In addition to anchorages in the floor and roof
structures, some rear safety belts have a
detachable anchor mounted to the outboard side
of the rear seats. This should remain attached,
except when removing the rear seats.
*
[SR04500(ALL)11/93]
The second row passenger side outboard seating
position uses a hook above the sliding/cargo
door to stow the shoulder safety belt when
entering or exiting the vehicle or when it is not
being used.
*
[SR04525(ALL)11/93]
NOTE: When the belt is stowed using the
hook, DO NOT use the hanging belt as
an assist when entering the vehicle.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

17 [SR04550(ALL)08/95]
three fourths page art:0020880-C
Proper stowage of shoulder safety belt
[SR04800(ALL)06/95]
Disengaging rear seat safety belts for seat
removal
[SR04850(ALL)05/95]
In order to remove the rear seat, the safety belt
must be disengaged from the seat. To disengage
the safety belt from the seat, insert a key or
small screwdriver into the slot provided on the
detachable anchor. Then lift upward.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

19 [SR05200(ALL)03/91]
Whenever a rear seat has been removed, the
tongue end of the detachable anchor must be
correctly stowed. See the following illustration.
[SR05300(ALL)03/93]
three fourths page art:0020786-A
Rear seat shoulder safety belt Ð stowage (with seat
removed)
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

44 [SR27100(ALL)08/95]
half page art:0011245-BChecking the retractor
*
[SR27201(ALL)05/95]
8. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR27205(ALL)05/95]
NOTE: To remove the retractor from automatic
lock mode, allow seat belt to retract
fully to its stowed position and the
retractor will automatically switch back
to the vehicle sensitive locking mode
for normal adult usage.
*
[SR27210(ALL)08/95]
RWARNING
Carefully follow all of the manufacturer's
instructions included with the safety seat
you put in your vehicle. If you do not
install and use the safety seat properly,
the child may be injured in a sudden stop
or collision.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

45
[SR27300(ALL)05/95]
Installing Child Safety Seats at
the Rear Center Seating Position
with Locking Adjustable Lap Belt
[SR27350(ALL)08/95]
DO NOT install a forward-facing child safety
seat in the third row center seating position.
Forward-facing seats must be installed with a
lap/shoulder belt, or a lap belt and top tether
strap.
[SR27400(ALL)06/95]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue toward the loose
end of webbing.
*
[SR27450(ALL)01/95]
2. Place the child safety seat in the center
seating position.
*
[SR27500(ALL)01/95]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
*
[SR27550(ALL)03/95]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
*
[SR27600(ALL)01/95]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
*
[SR27650(ALL)04/95]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

56
*
[SR30380(ALL)05/95]
To remove the child from the built-in child
seat:
[SR30390(ALL)06/95]
1. Squeeze the tabs on the top and bottom of
the chest clip and pull the halves apart to
open the chest clip. Refer to Figure 8.
*
[SR30400(ALL)06/95]
2. Press the release button on the crotch safety
belt buckle.
[SR30410(ALL)05/95]
3. Slide the shoulder belts off the child's
shoulders and remove the child. Refer to
Figure 6.
*
[SR30420(ALL)06/95]
To stow the built-in child seat:
[SR30430(ALL)05/95]
1. Return the child seat cushion to the upright
position and lift the protector flap toward
the headrest.
[SR30440(ALL)05/95]
2. Fasten the snaps securely.
[SR30450(ALL)05/95]
3. Pull on the headrest release strap and rotate
the headrest downward until it latches
against the child seat cushion.
[SR30460(ALL)05/95]
RWARNING
Always fasten the protector flap snaps
when stowing your child seats to prevent
the child seat cushion from rotating
forward in a collision.
[SR30470(ALL)05/95]
The seat can now be used by an adult.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

69
%*
[ST08160(ALL)03/95]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
*
[ST08170(ALL)08/95]
Fuel Pump Shut-Off Switch
*
[ST08180(ALL)07/95]
If the engine cranks but does not start or does
not start after a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device intended to stop the fuel
pump when your vehicle has been involved in a
substantial jolt.
*
[ST08190(ALL)03/95]
Once the shut-off switch is triggered, you must
reset the switch by hand before you can start
your vehicle.
[ST08200(ALL)07/95]
one third page art:0095071-A
Fuel pump shut-off switch location
*
[ST08225(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995

78 %
*
[LG04500(ALL)03/95]
Check Engine Warning Light
*
[LG04550(ALL)05/95]
The Powertrain On-Board Diagnostic II (OBD II)
system consists of the hardware and software
necessary to monitor the operation of the
powertrain. The OBD II system is designed to
check the function of the vehicle's powertrain
control system during normal operation. If an
emission problem is detected, the Check Engine
Warning Light (in the cluster) is turned on.
*
[LG04575(ALL)05/95]
Modification or additions to the vehicle may
cause incorrect operation of the OBD II system.
Additions such as burglar alarms, cellular
phones, and CB radios must be carefully
installed. Do not install these devices by tapping
into or running wires close to powertrain control
system wires or components.
[LG04600(ALL)07/95]
The light comes on briefly when you turn the
ignition key to the ON position, but it should
turn off when the engine starts. If the light does
not come on when you turn the ignition to ON
or if it comes on and stays on when you are
driving, have your vehicle serviced as soon as
possible. This indicates a possible problem with
one of the vehicle's emission control systems.
You do not need to have your vehicle towed in.
[LG04650(ALL)08/95]
If the light turns on and off at one (1) second
intervals while you are driving the vehicle, it
means that the engine is misfiring. If this
condition persists, damage could occur to the
engine or catalytic convertor. Have your vehicle
serviced at the first opportunity. You do not
need to have your vehicle towed in.
[LG04700(ALL)08/95]
If the light turns on and off on rare occasions
while you are driving, it means that a
malfunction occurred and the condition corrected
itself.
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995