1996 FORD AEROSTAR headlamp

64
*
[ST05150(ALL)03/95]
Starting Your Vehicle
%*
[ST05200(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05300(ALL)07/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST05400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05500(ALL)08/95]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST05600(ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[ST05750(ALL)03/95]
3. Make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
*
[ST06015(ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
%*
[ST06200(ALL)02/95]
Starting Your Engine
*
[ST06300(ALL)06/95]
To start your engine:
*
[ST06400(ALL)05/95]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[ST06425(ALL)03/95]
2. Turn the ignition key to the ON position.
*
[ST06451(ALL)06/95]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995

84 %
*
[LG08900(ALL)01/95]
High Beam Light
*
[LG09001(ALL)03/95]
This light comes on when the headlamps are
turned to high beam or when you flash the
lights.
*
[LG09025(ALL)11/89]
one inch art:0020537-B
High beam indicator light
%*
[LG09300(ALL)05/95]
Chime for Headlamps On
[LG09400(ALL)07/95]
This chime sounds if the driver or passenger
door is open when the parking lamps or
headlamps are on. The chime sounds until you
close the door, turn off the lamps or turn the
ignition to the ON position.
[LG09450(ALL)12/91]
NOTE: The chime will not sound when the
autolamp has activated the shutoff
delay.
%*
[LG09500(ALL)01/95]
Fuel Gauge
*
[LG09700(ALL)06/93]
The fuel gauge displays approximately how
much fuel is in the fuel tank only when the
ignition switch is ON.
*
[LG09850(ALL)01/95]
For a proper fuel gauge indication after adding
fuel, the ignition switch should be in the OFF
position while the vehicle is being refueled.
*
[LG09900(ALL)01/95]
The fuel gauge indicator may vary slightly while
the vehicle is in motion. This is the result of fuel
movement within the tank. An accurate reading
may be obtained with the vehicle on smooth,
level ground.
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995

110
*
[SC01800(ALL)11/89]
If the turn indicator light in the instrument
panel does not illuminate or remains on (doesn't
flash) when you signal a turn, the turn signaling
system is malfunctioning. Have this condition
corrected as soon as possible, but make sure that
you use the accepted hand signals in the
meantime.
%*
[SC03200(ALL)03/95]
High Beams and Flashing the Lamps
[SC03800(ALL)05/95]
one third page art:0095014-A
Headlamp high beam and flash-to-pass operation
%*
[SC04400(ALL)03/95]
Windshield Wipers and Washer
*
[SC04500(ALL)03/95]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
[SC04950(ALL)05/95]
one third page art:0095015-A
Interval wiper on turn signal lever Ð wiper and washer
operation
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995

265
Servicing Your Aerostar
%*
[SV00300(ALL)03/95]
Service Made Easy
*
[SV00400(ALL)01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(ALL)01/95]
1. When we can, we design parts that do not
need to be serviced.
*
[SV00600(ALL)01/95]
2. We want to make servicing your vehicle as
easy as possible. To help you:
*
[SV00700(ALL)01/95]
q
We highlight do-it-yourself items in yellow in
the engine compartment so that you can find
them easily.
*
[SV00800(ALL)01/95]
q
When possible, we design parts Ð such as
the headlamp bulbs Ð that can be replaced
without tools.
*
[SV00900(ALL)05/94]
q
We give you a Maintenance Schedule that
makes tracking routine service for your
vehicle easy. The maintenance schedule is
located in theMaintenance Schedule and Record
booklet.
*
[SV01000(ALL)01/95]
This chapter tells you about the basic parts that
you need to check and service regularly.
*
[SV01050(ALL)02/95]
If your vehicle needs professional servicing, your
dealership can provide the parts and service
required. Check yourWarranty Information Booklet
to find out which parts and services are covered.
Also see theCustomer Assistancechapter of this
Owner Guide.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

322 %
*
[SV44100(ALL)03/95]
Circuit Breakers
[SV44200(ALL)08/95]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instructions on the
charts given earlier in this chapter.
*
[SV44400(ALL)10/92]
However, you should know that the circuit
breakers will reset themselves and allow the
electrical parts to work again once the overload
on the circuit is removed. If the circuit breakers
continue to cut off electricity, have your vehicle's
electrical system checked.
*
[SV44450(ALL)02/95]
Diagnostic equipment is needed to check circuit
breakers. Refer to the manufacturer's
instructions.
[SV44500(ALL)08/95]
If you replace a circuit breaker, use one with the
same amperage rating. To remove a circuit
breaker, grip it with your finger and thumb and
pull it straight out of its socket.
%
*
[SV44600(ALL)03/95]
Lights and Bulb Replacement
*
[SV44700(ALL)01/95]
It is a good idea to check the operation of the
following lights frequently:
*
[SV44800(ALL)01/95]
q
headlamps
*
[SV44850(ALL)02/95]
q
high-mount brakelamp
*
[SV44900(ALL)01/95]
q
tail lamps
*
[SV45000(ALL)01/95]
q
brakelamps
*
[SV45100(ALL)01/95]
q
hazard flasher
*
[SV45200(ALL)01/95]
q
turn signals
*
[SV45300(ALL)01/95]
q
license plate lamp
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

323 %
*
[SV45400(ALL)01/95]
The alignment of your headlamps should be
checked if:
*
[SV45500(ALL)01/95]
q
oncoming motorists frequently signal you to
turn off your vehicle's high beams when you
do not have the high beams on
*
[SV45600(ALL)01/95]
q
the headlamps do not seem to give you
enough light to see clearly at night
*
[SV45700(ALL)01/95]
q
the headlamp beams are pointed substantially
away from a position slightly down and to
the right
%*
[SV45800(ALL)03/95]
Headlamp Bulb
*
[SV45900(ALL)01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV46000(ALL)05/95]
RWARNING
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp
the bulb only by its plastic base and do
not touch the glass. The oil from your
hand could cause the bulb to break the
next time the headlamps are operated.
*
[SV46050(ALL)12/91]
NOTE: If the bulb is accidently touched, it
should be cleaned with rubbing
alcohol before being used.
*
[SV46100(ALL)01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

324
*
[SV46300(ALL)03/95]
Removing the headlamp bulb
*
[SV46400(ALL)01/95]
1. Make sure that the headlamp switch on the
instrument panel is in the OFF position.
[SV46675(ALL)06/95]
2. Remove the screws that attach the headlamp
trim to the vehicle.
[SV46750(ALL)03/91]
3. Remove the headlamp trim.
[SV46820(ALL)03/91]
4. Remove the four screws (two on top and
two on bottom) that attach the headlamp to
the vehicle.
[SV46830(ALL)03/91]
quarter page art:0020850-A[SV46840(ALL)03/91]
NOTE: Do not disturb the aim adjusting
screws.
[SV46860(ALL)03/91]
5. Pull the headlamp away from the vehicle
and remove the electrical connector by
pulling rearward.
[SV46880(ALL)08/95]
6. Unsnap the bulb retaining wire and carefully
remove the bulb assembly from its socket by
gently pulling it out without turning it.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

325 [SV46890(ALL)03/91]
half page art:0020851-A
*
[SV46900(ALL)03/95]
Installing the headlamp bulb
*
[SV47000(ALL)02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
[SV47150(ALL)03/91]
2. Snap the retaining wire over both sides of
the bulb and connect the electrical connector.
[SV47275(ALL)03/91]
3. Position the headlamp on the vehicle and
install the four attaching screws.
*
[SV47300(ALL)02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995