1996 CADILLAC ELDORADO windshield wipers

Downloaded from www.Manualslib.com manuals search engine A E
With the ignition key in the ignition switch, you can turn
the switch to five different positions:
ACCESSORY (A): This position lets you use things
like the radio and the windshield wipers when the
engine is
off. To get into ACCESSORY, push in the key
and turn it toward you. The steering wheel will remain
locked, just as it was before you inserted the key.
LOCK (B): Before you put the key in, the ignition
will be in the
LOCK position. This is the only position
in which you can remove the key. This position locks
the ignition, steering wheel and transaxle. It’s a
theft-deterrent feature.
OFF (C): This position lets you turn off the engine but
still
turn the steering wheel. It doesn’t lock the steering
wheel like
LOCK. Use OFF if you must have your
vehicle in motion while the engine is
off (for example, if
your vehicle is being pushed).
RUN (D): This is the position for driving.
START (E): This starts the engine.
Retained Accessory Power
The following accessories on your Cadillac may be used
for up to
10 minutes after the ignition key is turned
to
OFF:
Radio
0 Power Windows
Astroroof
Power to these accessories stops after
10 minutes or if
either door is opened. If you want power for another
10 minutes, turn the ignition key to RUN and then back
to
OFF.
2-15

Downloaded from www.Manualslib.com manuals search engine Flash-To-Pass ,
This lets you use the high-beam headlamps to signal the
driver
in front of you that you-want to pass. It works
everi if tfie headlamps are off.
Pull the turn signal lever toward you to use. When
you do:
If the headlamps are off, the high-beam headlamps
will
'turn on. They'll stay on as long as you hold the
lever there. Release the lever
to turn them off.
0 If the headlamps are on low beam, they will shift to
high beam and stay there. Pull the lever toward you
to return
to low beam.
0 If the headlamps are on high beam, they will switch
to low beam. To return to high beam, pull the lever
toward you.
Windshield Wipers
WIPER: Turn the band on the turn signal lever to
control the wipers.
MIST: Turn the band toward you and then release it for
a single wipe cycle. For more cycles, hold the band on
MIST longer.

Downloaded from www.Manualslib.com manuals search engine LO or HI: Turn the band away from you to either LO
(low speed) or to HI (high speed), depending on the
wiper speed you want.
DELAY You can set the wiper speed for a long or short
delay between wipes with this setting. Move the band to
the DELAY position. The closer you move
it to LO, the
shorter the delay.
OFF: Turn the band to OFF to turn off the wipers.
Be sure to clear ice and snow from the wiper blades -
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them.
If the blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools. Clear
away snow or ice to prevent an overload.
Rainsense V- ?ers (ETC Only)
This feature is mounted on the passenger’s interior side
of the windshield behind the rearview mirror and is used
to automatically operate the wipers by monitoring the
amount
of moisture that is on the windshield.
The Rainsense system can
be activated by turning the
wiper stalk to one of the
five sensitivity levels within the
AUTO DELAY area. Turn the stalk toward you for
minimum sensitivity and away from
you for maximum
sensitivity.
A single wipe will occur each time you turn
the wiper stalk to a higher sensitivity level. An initial
wipe occurs when you turn the ignition on as a reminder
that Rainsense is active. The windshield wipers also
~. ~ 2-33

Downloaded from www.Manualslib.com manuals search engine remain in a “high park” position, even when the ignition
is turned
OFF.
The Rainsense wipers operate in a delay mode as well
as, a continuous low or high speed depending on the
amount of moisture and
the sensitivity level. The MIST
and “wash” cycles operate as normal and are not
effected by the Rainsense function.
NOTICE:
The Rainsense feature should be turned off when
going through a car wash to avoid damage.
It is important to note that the Rainsense wiping feature
(AUTO DELAY) can be overridden at any time by
manually changing the wiper control to
LO or HI speed.
Note that if
you ever need to replace the windshield,
make sure
it is Rainsensor compatible.
Windshield Washer
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice
on the windshield, blocking
your vision.
Press and hold the PUSH paddle to wash the windshield
Release the paddle when you have enough fluid. The
wipers
will clear the windshield and either stop or return
to your preset speed.
LOW WASHER FLUID will be displayed on the DIC
when the washer fluid reaches a low level.
Driving without washer fluid can be dangerous.
A bad
mud splash can block your vision and you could hit
another vehicle
or go off the road. Check the washer
fluid level often.
2-34 -

Downloaded from www.Manualslib.com manuals search engine Lamps
I"
..
, __.",
The control on the left side
of the instrument panel
controls these lamp systems:
OFF,
'f"
0 Headlamps
Taillamps
0 Parking Lamps
0 Sidemarker Lamps
0 License Plate Lamp
0 Underhood Lamp
Fog Lamps
Instrument Panel Lights
Interior Courtesy Lamps Pull the knob out to the first stop to
turn on the parking
and taillamps, sidemarker lamps and instrument panel
lights.
Pull the knob out all the way to turn on the
headlamps.
You can brighten or dim the instrument cluster
by rotating the headlamp knob. Press the knob all the way
in to turn them off. The exterior lamps will automatically
turn on after several seconds of wiper activation.
Headlamps
Wiper Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately
20 seconds.
In order to operate the wiper activated headlamps, the
twilight sentinel must be in the on position. This feature
lights the way in poor weather and it also makes your
vehicle more visible to other drivers.
If the wiper
activated headlamps are on, and the ignition switch is
turned off, the wiper activated headlamps will
immediately turn off.
The wiper activated headlamps will deactivate
if you
turn off the twilight sentinel or
if the windshield wipers
have been turned off for a period of one or two seconds.
2-39

Downloaded from www.Manualslib.com manuals search engine Wiper Blade Replacement
It’s a good idea to clean or replace the wiper blade
assembly on a regular basis or when worn. For proper
windshield wiper blade length and type, see “Normal
Maintenance Replacement Parts” later in this section.
To replace the wiper blade assembly:
1. Turn the ignition key to ACCESSORY and turn the
wipers on. Position the wipers on the windshield in
the “mid” wipe position. Then with the door open,
turn the key to OFF.
2. Insert a screwdriver into the slot as shown and press
down to release the wiper blade assembly.
3. Align the wiper arm pin with the hole on the wiper
blade assembly and snap it into place to install.
6-35
1

Downloaded from www.Manualslib.com manuals search engine Electrical System
Add-on Electrical Equipment
I NOTICE:
Don’t add anything electrical to your Cadillac unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty.
Some add-on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Bef‘ore attempting to
add anything electrical to your Cadillac, sce ”Servicing
Your Air Bag-Equipped Cadillac” in the Index.
Headlamp Wiring
The headlamp wiring has an individual fuse which is
powered
by a MaxiFuse@. An electrical overload will
cause the lamps to
go on and off, or in some cases to
remain
off. If this happens, have the headlamp wiring
checked right away.
MaxiFuse
is a registered trademark of Little Fuse
Incorporated.
Windshiek Xper Fuses
The windshield wiper motor is powered by a MaxiFuse.
If the motor overheats due to heavy snow, etc., the
wipers will stop until the motor cools.
If the overload
is caused by some electrical problem, be sure to have
it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit
until the problem is fixed or goes away.
6-54

Downloaded from www.Manualslib.com manuals search engine INT LPS CIG LTAl
LHDLP Lo R HDLPLO LHDLPHI RHDLP HI SENSE
, HDLPS , I HAZARD I , STOP I I MIRROR , I FOGIDRL ,
IGN O(ENG) CRANK WIPERS
FUSE CENTER IDENTIFICATION
- - -
OXY SEN2 OXY SEN1 FUEL PUMP
CRUISE RELAY
DISTR PCM(IGN ECS ndn - ---
PCM BAT AIC COMP n& n I
AiC COMP RE LAY
FRONT OF VEHICLE 3648830 / I
--- I '/
Fuse Usage
INT LPS Trunk Lamp, Courtesy Lamps,
Front Vanity Lamps, Glove
Box
Lamp, Garage Door Opener,
Courtesy Lamp Relay
CTG LTRl Front Cigarette Lighter (Full
Console Only), Rear Lighter
L HDLP LO Left Low-Beam Headlamp
Fuse
R HDLP LO
L HDLP HI
R HDLP HI
SENSE
-
HDLPS
HAZARD
STOP
Usage
Right Low-Beam Headlamp,
Light Emitting Diode (LED) on
Headlamp Switch
Left High-Beam Headlamp
Right High-Beam Headlamp Heated Windshield Control
(Optional)
Headlamp Switch and Relay,
High/Low Beam Control Relay,
Right and Left
Low Beam (I-Beam),
Right and Left High Beam
Electronic Flasher Module,
Turn/Hazard Module, Right and Left Turn Lamps, Back-up Lamps, Right
and Left Front Turn Lamps, Right
and Left Repeater Lamps (Export)
Stoplamp Switch, Centered
High-Mounted Stoplamp
(CHMSL), Turn Hazard Switch,
ABS Controller. Stepper Motor
Cruise Control, Right and Left
Rear Stoplamps