1995 RENAULT MEGANE SCENIC fuel filter

DIESEL EQUIPMENT
Specifications
13
Vehicle GearboxEngine
Type SuffixBore
(mm)Stroke
(mm)Capacity
(cm
3)RatioCatalytic
converterDepollution
standard
BA0U JB3 F8Q 620 80 93 1 870 21.5/1 None EU93
BA0A JB3 F8Q 620 80 93 1 870 21.5/1 C25 EU96
ENGINE SPEED (rpm.)
Idle speed Maximum no loadMaximum with
load
SMOKE OPACITY
Homologation value Legal maximum
825 ± 25 5 200 ± 100 4 600 ± 100 1.24 m
-1 (40 %) 2 m -1 (55 %)
DESCRIPTION MAKE /TYPE SPECIAL NOTES
Injection pump
Pumps R598-2 and R598-3 differ
in that a coded fuel shut off
valve has been addedBOSCH
VE 4/8F 2300R598
VE 4/8F 2300R 598-1*
VE 4/8F 2300R 598-2
VE 4/8F 2300R 598-3*Rotary pump with:
- separate idle lever
- solenoid controlled load dependence (ALFB)
- post-heating and EGR cut-out microswitch
- air conditioning cut-out microswitch*
Pump timing obtained by 8mm
diameter TDC pin (Mot. 1079)Pump piston lift: 0.82 ± 0.04 mm
(the setting value is stamped on the load lever)
Injector holders
BOSCH KCA 17 S 42Tightening torque : 7 daN.m
Injectors BOSCH
DNOSD 302 Test: 130 bars
Maximum gap: 8 bars
Fuel filter
PURFLUXPriming pump
The filter is fitted with an electrical fuel heater
EGR solenoid valve Voltage: 12 volts
Resistance : 10 ± 5 Ω
Fuel pipes External diameter : 6 mm
Internal diameter : 2.5 mm
Length: 400 mm
Pre-heating unit
NAGARESWith pre-post-heating function and cold start
functions and fast idle solenoid
Heater plugs BOSCH Current: 15 A approximately after 8 seconds
heating
Tightening torque : 2 daN.m
+8
- 5
13-15

DIESEL EQUIPMENT
Fuel filter
13
LOCATION
Principle of the electric heater
The heater has heated studs. They are ceramic,
made from barium titanate which has a positive
temperature coefficient, meaning that its
resistance increases as its temperature increases.
99332R
1Fuel filter
2Electric heater
3Hand priming unit
The electric diesel fuel heater and the thermostat
are integral in the head of the filter.
DIAGRAM
PRJ99258
449Electric heater
450Diesel heating relay
597Engine fuse box
645Passenger compartment fuse box Operating temperature
Electrical circuit closes: 0°C
Electrical circuit opens: from 8°C
Heater power: 150 W
13-37

99461R
DIESEL EQUIPMENT
Fuel filter
13
REMOVAL - REFITTING (Special notes)
To remove the filter assembly use tool Mot. 1311-
06 for the quick release unions.
When refitting, refit the quick release unions by
hand and ensure they click back together correctly
(two O rings ensure sealing).
99332S
13-38

INJECTION
General
17
K7M engine
1Injection computer
2Pinking sensor
3Coolant temperature sensor
4TDC sensor
5Fuel vapour recirculation solenoid valve
7Idle speed regulation stepping motor
8Throttle position potentiometer
9Air temperature sensor
10Absolute pressure sensor
11Canister
12Coil for cylinders 1 - 4
13Coil for cylinders 2 - 3
14Fuel pump relay
15Anti-interference condenser
16Air filter
17Oxygen sensor
18Power assisted steering pressostat
19EGR solenoid valve
20Vacuum reservoir
21EGR air filter
LOCATION OF COMPONENTS
17-9

INJECTION
General
17
F3R engine
1Injection computer
2Pinking sensor
3Coolant temperature sensor
4TDC sensor
5Fuel vapour recirculation solenoid valve
6Cylinder reference sensor
7Idle speed regulation solenoid valve
8Throttle position potentiometer
9Air temperature sensor
10Absolute pressure sensor
11Canister
12Coil for cylinders 1 - 4
13Coil for cylinders 2 - 3
14Fuel pump relay
15Anti-interference condenser
16Air filter
17Oxygen sensor
LOCATION OF COMPONENTS
17-11

- the heat shield from the exhaust manifold,
- the catalytic converter (disconnect the oxygen
sensor) and secure the exhaust pipe to the
body,
- the horn,
- the acoustic tie-rod between the shock
absorber turrets,
- the air filter,
- the earth strap,
- the absolute pressure sensor,
- the expansion bottle and secure it to the
engine.
Disconnect:
- the accelerator cable as well as the kickdown
switch connector,
- the brake servo pipe,
- the relay plate and the electrical connectors
from the engine connection unit,
AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
- the connector from the automatic transmission
computer,
- the canister pipe.
Remove the battery mounting bracket.
- the heating pipes on the thermostat.
Unclip the radiator and move it away by securing
it to the engine.
98756R
Disconnect:
- the injection supply wire located in the scuttle
panel as well as the starter motor supply,
- the fuel inlet and outlet hoses using Mot. 1311-
06, unclip them from their support,
99461R
23-16