1995 RENAULT MEGANE SCENIC wiring

OPENINGS OTHER THAN SIDE DOORS
Hood cover
Disconnect the electrical wiring.
Separate the rams.
Remove the bolts.
48
PRE4802
12474S12473S
48-2

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete manual or electrohydraulic hood
52
Remove:
- the front connecting crossmember mounting
bolts (2),
- the connecting crossmember.
Disconnect the hood microswitch wiring.WW W W
AA A A
RR R R
NN N N
II I I
NN N N
GG G G
:: : :
for vehicles fitted with an electrohy-
draulic mechanism, the hydraulic system
MM M M
UU U U
SS S S
TT T T
NN N N
EE E E
VV V V
EE E E
RR R R

be operated after removal of the connec-
ting crossmembers (risk of losing the basic hood
adjustment). It is therefore
EE E E
SS S S
SS S S
EE E E
NN N N
TT T T
II I I
AA A A
LL L L
to operate
the hood
MM M M
AA A A
NN N N
UU U U
AA A A
LL L L
LL L L
YY Y Y.
To do this, open the hydraulic unit bolt (A) as far
as possible.Remove the main bearing mounting bolts (3).
12172-1R
12294R
12292R
52-2

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete manual or electrohydraulic hood
52
REFITTING
Fit the folded hood in its housing.
Secure the main bearing without tightening it.
Close and lock the hood.
Tighten the main bearing mounting bolts (3) to a
torque of 20 N.m.
Fold the hood.
Position the rear roof arch ram, secure it to the
clamp (6) and the pin (5) (electrohydraulic mecha-
nism).
Place the hood in the neutral position, rear roof
arch vertical.
Connect the hood microswitch wiring.
Fit the main ram and clamp it.
Position the connecting crossmember and tighten
the mounting bolts to a torque of 20 N.m.
Tighten the hydraulic unit bolt and operate the
electrohydraulic system several times (opening -
closing) in order to bleed the hydraulic circuit
(automatic bleeding).
52-4

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
12290R
Disconnect the wiring (1).
Remove the clips (2) and remove the ram.
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing:
- the bench seat cushion and backrest,
- the quarter light trims,
- the boot side fittings
open the hood cover and immobilise it.Remove the connecting crossmember.
PRE5203
12172-1R
Open the bolt (A) as far as possible.
52-10

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
Remove the rear roof arch ram pin (5) then the
clamp (6). Separate the ram. Remove:
- the main bearing mounting bolts (see section
52).
- the main ram upper clamp.
Separate the main ram from the frame.
Fold the hood.
Disconnect the hood microswitch wiring (left-
hand side)
Detach the hydraulic pipes.
Remove the main bearing mounting bolts.
Raise and immobilise the main bearings in order
to detach the hydraulic system clearance hole.
Remove:
- the electric relays bracket,
- the lower yoke nut (3),
- the ram.
12293R112291R
12289R
52-11

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Insert the rams - pipes assemblies through the
clearance holes in the following order:
1 right-hand side assembly
2 left-hand side assembly
3 hood cover assembly.
Refit the pump.
After refitting all of the components, close the hy-
draulic unit bolt and operate the electrohydraulic
system several times (opening - closing) in order to
purge the hydraulic circuit.
WW W W
AA A A
RR R R
NN N N
II I I
NN N N
GG G G
:: : :
when work is carried out on the hy-
draulic system, follow the recommendations be-
low and keep everything clean.
• Before removal, clean the pipe unions, their
environment and the reservoir carefully.
• Place the system on thick paper. Do not use a
fluffy cloth.
• Cover the system carefully if the work is not
carried out immediately.
• Do not remove the replacement parts from
their packaging until immediately before they
are fitted.
• Do not blow with compressed air when the
hydraulic system is open.
OO O O
NN N N
LL L L
YY Y Y
use EE E E
SS S S
SS S S
OO O O

UU U U
NN N N
II I I
VV V V
II I I
SS S S

JJ J J
22 2 2
66 6 6

OO O O
II I I
LL L L for filling the hy-
draulic system. Disconnect the wiring.
Remove:
- the housing,
- the pump mounting bolts (4),
- the pump.
Remove the rams - pipes assemblies in the follo-
wing order:
1 hood cover assembly
2 left-hand side assembly
3 right-hand side assembly.
12172-1R1
52-12

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system (pipes)
52
Remove:
- the pump connectors (1) and wiring,RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the complete system, mark the co-
lour of the connectors (1) on the solenoid valves.
PRE5204
12298R
12297R
- the pump bolts (2) and bracket. B = blue
R = red
52-13

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system (pipes)
52
Diagram of fitting of pipes at the ram end
Pipe Piston rod Piston base end Rams
E X Hood cover
N X Hood cover
A X Left-hand main ram
W X Left-hand main ram
B X Right-hand main ram
X X Right-hand main ram
R X Left-hand rear roof arch
P X Left-hand rear roof arch
S X Right-hand rear roof
arch
O X Right-hand rear roof
arch
Tighten the pipe unions to a torque of 15 N.m.
Refit the pump bracket.
Clip the solenoid valve control connectors (1) and the pump wiring.
52-15