1995 OLDSMOBILE AURORA wiring

Safety Belt Reminder Light
FASTEN
BELTS
When the key is turned to RUN or START, a chime will
come on for about eight seconds to remind people to
fasten their safety belts.
The safety belt light will also
come on and stay on for about
70 seconds. If the driver’s
belt is already buckled, neither the chime nor the light
will come on.
Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows
AIR BAG. The system checks the
air bag’s electrical system for malfunctions.
The light
tells you
if there is an electrical problem. The system
check includes the air bag sensors and modules, the
wiring and
the diagnostic module. For more information
on the air bag system, see “Air
Bag” in the Index.
AIR BAG
You will see this light
flash for
a few seconds
when you turn your
ignition to RUN or
START. Then the light
should go out. This
means the system is
ready.
If the air bag readiness light doesn’t come on when you
start your vehicle, or stays on, or comes on when you
are driving, your air bag system may not work properly.
Have your vehicle serviced right away.
2-64
ProCarManuals.com

Making Turns
I NOTICE:
Making very sharp turns while trailering could
cause the trailer to come in contact with the
vehicle. Your vehicle could be damaged. Avoid
making very sharp turns while trailering.
When you‘re turning with a trailer, make wider turns
than normal.
Do this so your trailer won’t strike soft
shoulders, curbs, road signs, trees, or other objects.
Avoid jerky or sudden maneuvers. Signal well
in
advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle has to have a
different turn signal flasher and extra wiring. The green
arrows on your instrument panel will flash whenever
you signal a turn or lane change. Properly hooked
up,
the trailer lamps will also flash, telling other drivers
you‘re about to turn, change lanes or stop.
When towing
a trailer, the green arrows on your
instrument panel will flash for turns even
if the bulbs on
the trailer are burned out. Thus. you may think drivers
behind you are seeing your signal when they are not. It’s
important to check occasionally to be sure
the trailer
bulbs are still working.
Driving On Grades
Reduce speed and shift to a lower gear h4for-c you start
down a long or steep downgrade.
If you don’t shift
down, you might have to use your brakes so much that
they would get hot and no longer work well.
ProCarManuals.com

3. Unclip the bulb
assembly from the
wiring harness and
replace the bulb
assembly. High Beam Bulbs
1. Pull up on the wiring harness. This unlocks the bulb.
4. Reverse steps 1-3 to replace the bulb assembly,
headlamp housing and air cleaner cover and tube.
2. Now you can reach in behind the lamp housing and
pull out the bulb.
3. To replace the bulb, angle the new bulb into the
empty socket.
4.
Push the base of the bulb down to lock it into place.
6-3 1
ProCarManuals.com

4. Check to make sure the safety belts are properly
routed and that
no portion of any safety belt is
trapped under
the seat. Also make sure the seat
cushion
is secured.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by
a combination of fuses and circuit
breakers. This greatly reduces the chance
of damage
caused by electrical problems.
There are three main fuse panels.
Two are located under
the rear seat.
To access these panels, you’ll need to
remove the seat. See the previous description under
“Removing
the Rear Seat Cushion” to see how. This
procedure
is somewhat difficult. You may wish to have
your retailer replace the fuse, instead.
V
Once the seat is removed,
you’ll find two fuse panels
on the driver’s side of the
battery. Each
is protected by
a plastic box with four tabs.
Pull up on all four tabs at
the same time to loosen
them and pull off the box.
Of these two panels, the cover on the passenger-side
fuse panel
has an extra plastic cap attachment. You’ll
need to slide this out of the grooves which hold it there
before removing the rest
of the box.
To replace the covers, line the four tabs up and simply
snap
them back into place. The extra plastic cap
attachment slides back into place.
6-54
ProCarManuals.com

Maxifuse/Relay Center
It’s easy to check the fuses in this underhood relay
center. There are two locking arms on either side
of the
base of the cover. Reach down and unsnap each one by
pulling the cover toward you, then pushing
it away
while pulling up. Remove the cover. The inside of the
cover has a chart that explains the features and controls
governed
by each fuse and relay.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the wiring harness. An electrical overload will cause the
lamps
to go on and off, or in some cases to remain off. If
this happens, have your headlamp system checked right
away.
Windshield Wipers
The windshield wiper motor is protected by an internal
circuit breaker and a fuse in the fuse panel
on the other
side
of the instrument panel. If the motor overheats due
to heavy snow, etc., the wiper will stop until the motor
cools.
If the overload is caused by some electrical
problem, have
it fixed.
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy. the circuit breaker opens and closes,
protecting the circuit
until the problem is fixed.
ProCarManuals.com