1995 LAND ROVER DISCOVERY oil

12ENGINE
18
REPAIR 10.Apply sealant to flywheel housing mating face on
cylinder block (Fig. J5944).
11.Fit housing to cylinder block and secure with
bolts as removed. Tighten to
45 Nm.
12.Remove surplus sealant from block.
13.Refit starter motor.
14.Refit flywheel.
See Flywheel
15.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
16.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
17.Reconnect battery negative lead.OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under filter.
2.Unscrew filter anti-clockwise, using a strap or
spanner.
Refit
3.Smear clean engine oil on seal of new filter.
4.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. Do not over tighten.

Tdi
19
REPAIR OIL TEMPERATURE CONTROL VALVE
Service repair no - 12.60.69
Remove
1.Disconnect oil cooler pipes.
2.Remove two bolts and carefully withdraw
thermostat extension housing (1) complete with
O ring seal (2), thermostat (3), two washers (4)
and spring (5).
3.Clean adaptor housing.
4.Inspect all parts and renew as necessary.
Refit
5.Fit thermostat to extension housing ensuring pin
locates in hole.
6.Fit two washers and spring to thermostat.
7.Fit a new 'O' ring to extension housing.
8.Insert spring into adaptor and secure extension
housing to adaptor with bolts. Tighten to
9 Nm.
OIL FILTER HEAD GASKET
Service repair no - 12.60.03
Renew
1.Disconnect oil cooler pipes.
2.Disconnect pressure switch lead.
3.Remove securing bolts and withdraw head
complete with gasket.
4.Clean mating faces.
5.Refit head with new gasket.
6.Secure with bolts. Tighten to
45 Nm.
7.Refit pipes and reconnect pressure switch.

12ENGINE
22
REPAIR
NOTE: Cylinder head retaining bolts can
be used up to a maximum of five times.
34.Lubricate threads of bolts with light oil and fit to
positions illustrated.
Bolt sizes:
M10 x 117mm locations 3, 5, 12, and 13.
M12 x 140mm locations 1, 2, 7, 8, 9, 10, 15, 16, 17,
and 18.
M12 x 100mm locations 4, 6, 11, 14.
35.Tighten bolts so that underside of heads just
make contact with cylinder head.
36.Following the sequence illustrated tighten all
bolts to
40 Nm.
37.Attach degree disc special tool LRT-12-007 to a
power bar.
38.Make a suitable pointer from welding rod and
attach to a bolt screwed into a rocker shaft
securing bolt hole.
39.Tighten all bolts through 60°strictly in sequence
illustrated.
40.Repeat 60°tightening procedure, again strictly in
sequence illustrated.
41.Tighten the ten longer bolts (M12 x 140mm) a
further 20°, again following the sequence
illustrated.
NOTE: Repositioning of the pointer will be
necessary to reach all bolts, the pointer
can be fitted to the rocker shaft securing
studs using two nuts.
CAUTION: The double tightening
procedure must be carried out, on no
account should tightening be performed in
one operation, otherwise damage to the cylinder
head may occur.
42.Fit valve stem caps.
43.Fit push rods to locations from which they were
removed.
44.Fit rocker shaft assembly evenly tightening
securing nuts and bolts to correct torque.
45.Fit rocker cover ensuring oil seal is satisfactory
for continued use.
NOTE: Rocker cover seals can be re-used
up to a maximum of five times.
46.Secure rocker cover with special seal washers
and nuts tightened to correct torque.
47.Refit remainder of items by reversing operations
1 to 22 tightening securing bolts to correct torque
where applicable.

Tdi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

Tdi
3
SPECIFICATIONS, TORQUE Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Generator to auxiliaries mounting bracket 25.................................................
Starter motor (bolt and nut) 45........................................................................
Tachometer electrical connection 4...............................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................

V8i
1
DESCRIPTION AND OPERATION DESCRIPTION
The V8i engine has cast aluminium cylinder heads
and cylinder block. The two banks of steel cylinder
liners which are pressed down to stops in the block,
are set at 90°to one another. The three ringed
aluminium pistons transmit the power through the
connecting rods to a cast iron five bearing crankshaft,
which drives the centrally located camshaft via a
duplex type chain.
The electronic ignition distributor is driven by a gear
off the front of the camshaft and the lubrication oil
pump is driven by a gear off the front of the
crankshaft. The overhead inlet and exhaust valves are
operated by rocker shafts, pushrods and self adjusting
hydraulic tappets.
Multiport fuel injection ensures that engine
performance, economy and exhaust emissions are
automatically correct for the demands of highway and
off road operation.

12ENGINE
2
DESCRIPTION AND OPERATION
1. Cylinder block
2. Pistons and gudgeon pins (8)
3. Connecting rods (8)
4. Core plugs
5. Camshaft
6. Dipstick
7. Camshaft key
8. Timing chain
9. Camshaft sprocket
10. Distance piece
11. Distributor drive gear
12. Distributor
13. Front cover
14. Front cover oil seal
15. Coolant pump
16. Crankshaft damper / pulley17. Crankshaft sprocket
18. Crankshaft sprocket key
19. Crankshaft
20. Centre main bearing shells (2)
21. Crankshaft rear oil seal
22. Spacer
23. Adaptor plate
24. Rear main bearing cap, shell and side seals
25. Connecting rod caps
26. Main bearing caps and shell bearings
27. Oil filter
28. Oil pump suction pipe/strainer
29. Oil sump
30. Oil sump drain plug
31. Oil pump drive key

V8i
3
DESCRIPTION AND OPERATION
1. Cylinder heads (2)
2. Rocker covers (2)
3. PCV filter
4. Rocker shafts (2)
5. Hydraulic tappets (8)
6. Pushrods (8)
7. Rocker brackets (8)
8. Rocker arms (4) left and (4) right
9. Rocker shaft springs (6)
10. Inlet manifold
11. Plenum chamber lower
12. Ram pipes (8)13. Plenum chamber upper
14. PCV air intake filter
15. Oil filler
16. Thermostat
17. Thermostat cover
18. Inlet valve seal, spring, cap and collets (8)
19. Exhaust valve seal, spring, cap and collets (8)
20. Inlet valve and seat (8)
21. Exhaust valve and seat (8)
22. Inlet manifold gasket and seals
23. Cylinder head gaskets (2)
24. Valve guides (16)