INTRODUCTION
3
INFORMATION SYNTHETIC RUBBER
Many '0' ring seals, flexible pipes and other similar
items which appear to be natural rubber are made of
synthetic materials called Fluoroelastomers. Under
normal operating conditions this material is safe, and
does not present a health hazard. However, if the
material is damaged by fire or excessive heat, it can
break down and produce highly corrosive Hydrofluoric
acid which can cause serious burns on contact with
skin. Should the material be in a burnt or overheated
condition handle only with seamless industrial gloves.
Decontaminate and dispose of the gloves immediately
after use.
If skin contact does occur, remove any contaminated
clothing immediately and obtain medical assistance
without delay. In the meantime, wash the affected
area with copious amounts of cold water or limewater
for fifteen to sixty minutes.
RECOMMENDED SEALANTS
A number of branded products are recommended in
this manual for use during maintenance and repair
work.
These items include:
HYLOMAR GASKET AND JOINTING COMPOUND
and
HYLOSIL RTV SILICON COMPOUND.
They should be available locally from garage
equipment suppliers. If there is any problem obtaining
supplies, contact the following company for advice
and the address of the nearest supplier.
MARSTON LUBRICANTS LTD.
Hylo House,
Cale Lane,
New Springs,
Wigan WN2 1JR
Tel 01942 824242USED ENGINE OIL
WARNING: Prolonged and repeated
contact with engine or motor oil will result
in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
Used engine oil contains potentially harmful
contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities should be provided.
Handling precautions
1.Avoid prolonged and repeated contact with oils,
particularly used engine oils.
2.Wear protective clothing, including impervious
gloves where applicable.
3.Do not put oily rags in pockets.
4.Avoid contaminating clothes, particularly
underwear, with oil.
5.Overalls must be cleaned regularly. Discard
unwashable clothing and oil impregnated
footwear.
6.First aid treatment must be obtained immediately
for open cuts and wounds.
7.Use barrier creams, before each work period, to
help the removal of oil from the skin.
8.Wash with soap and water to ensure all oil is
removed (skin cleansers and nail brushes will
help). Preparations containing lanolin replace the
natural skin oils which have been removed.
9.Do not use gasoline, kerosene, diesel fuel,
petrol, thinners or solvents for washing the skin.
10.If skin disorders develop, obtain medical advice.
11.Where practicable, degrease components prior
to handling.
12.Where there is a risk of eye contact, eye
protection should be worn, for example, goggles
or face shields; in addition an eye wash facility
should be provided.
Disposing of used oils
Environmental protection precaution
It is illegal to pour used oil onto the ground, down
sewers or drains, or into waterways.
Dispose of used oil through authorised waste disposal
contractors. If in doubt contact your Local Authority for
advice on disposal facilities.
57STEERING
10
FAULT DIAGNOSIS VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures.
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test.
See Road Test Procedure
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks.
See Visual
and Safety Checks
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock BUT not necessarily
return to exactly straight ahead without
assistance from the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure.
See Stiff Steering Checklist
If not proceed with basic checks and adjustments.
See Visual Check and Basic Adjustments
