1995 CHEVROLET ASTRO CARGO VAN lock

Downloaded from www.Manualslib.com manuals search engine Vehicle Symbols
These are some of the symbols you will find on your vehicle. For example,
these symbols are used
on an original battery:
A
17
Caurron
Possible
Injury
Protect Eyes Caustic Battery Acid Spark or Flame Could
by Shielding Could
Cause Burns Explode Battery
Avoid Sparks
or Flames
These symbols are important for you and your passengers whenever your
vehicle is driven:
Qe
-I I
Fasten Safety Door LocWUnlock
Belts
vi

Downloaded from www.Manualslib.com manuals search engine These symbols are used on warning and indicator lights:
Engine Coolant
Temperature System
I I
Fue
I
I II
Brake 4 - Wheel
(Digital Cluster)
Anti - Lock
(Digital Cluster)
Here are some other symbols you may see:
Fuse Lighter
Horn Engine
Oil
Pressure
I
Speaker
viii

Downloaded from www.Manualslib.com manuals search engine Manual Front Seat
The bucket seats can
be adjusted forward or
rearward by the lever
at the front
of the seat.
Move the seat adjustment
lever at the front of the seat towards the driver's
door
to unlock it. Slide the seat to where you want it. Then release the lever
and try to move the seat with your body,
to make sure the seat is locked into
place.
Power Driver's Seat
You can adjust the seat before entering the vehicle.
The front control makes the front of the seat go up and down.
The rear control makes the rear of the seat
go up and down.
The center control
makes the whole seat go up and down or forward and
rearward.
1-2

Downloaded from www.Manualslib.com manuals search engine Reclining Bucket Seats
If you have this feature, you will have a lever on the inside of the seat to
adjust the seatback.
You can adjust the
seatback by lifting
the
lever. Release the
lever
to lock the seat
back where you want
it. Pull up
on the lever
and the seat will
go to
an upright position.
But don't have
a seatback reclined if your vehicle is moving.
1-3

Downloaded from www.Manualslib.com manuals search engine Move the seat
adjustment lever
at the
front of the seat
towards the
passenger’s side to
unlock it. Slide the
seat to where
you
want it. Then release
the lever and try to
move the seat with
your body, to make sure the
seat is locked
into place.
The non-touring center bench seat has
a pivoting right armrest. The left
armrest can also
be used as a storage compartment.
The storage compartment and beverage cooler can also be used as rear seat
armrests. See “Storage Compartments”
in the Index.
The optional touring bench seats come
with moveable armrests, individual
reclining seatbacks, adjustable headrests and
a fold down center console.
To adjust your
seatback, pull up
on
the lever on the lower
outside of the seat.
The center bench
seatbacks will recline
further back than the
rear bench seatbacks.
1-5

Downloaded from www.Manualslib.com manuals search engine To raise or lower the
center console, press
the button between the
beverage holders.
Only sit
in the center
seating position when
the console
is in an
upright position. For
details about
headrests, see “Head
Restraints’’ in this
section.
Seatback Latches (Non-Touring Bench Seats)
To fold your
non-touring seatback
forward,
pull up on
the latch release lever
while pulling the
seatback toward
you.
The lever is on the
right rear
of your seat.
After the latch has been released, push
the seatback down until it locks in
place.
To raise the seatback, unlock the seat by pushing forward on the lever.
Make sure the seatback
is locked when it is put back in the upright position.
1-6

Downloaded from www.Manualslib.com manuals search engine 3. If you have a
safety belt guide
on your seat, pull
the safety belt all
the way out
through the
guide.
4. Pull up on the seatback latch on
the right rear
of
the front seat.
Push the seatback
down until it
locks in place
(non-touring
bench seats only).
5. Lift up on the seat release latch. The latches are near the floor on the
rear legs
of the seat. To relieve pressure on the latch, pull back on the
seat.
6. Lift up on the
rear
of the seat to
remove the seat assembly from
the rear latch
pins. Then, pull
back and lift the seat out
of the
vehicle.
1-8

Downloaded from www.Manualslib.com manuals search engine To Install The Seat
1. Lower the seat into position. Make sure the front retainers are hooked
onto the anchor pins. Pull the seat down to latch
the rear retainers.
Make sure the seat is locked in
by pulling up and down on the seat.
A CAUTION:
A seat that isn’t locked into place properly can move around in a
collision or sudden stop. People in the vehicle could be injured.
Be sure
to lock the seat into place properly when installing it.
~~
A CAUTION:
A seat that isn’t locked into place properly can move around in a
collision or sudden stop. People in the vehicle could be injured.
Be sure
to lock the seat into place properly when installing it.
2. Raise the seatback by pushing forward on the latch at the right rear of
the seat. Pull up on the seatback until it is locked securely in the up
position.
1-9