1994 MAZDA MX-5 air condition

TROUBLESHOOTING GUIDE INSPECTION Disconnect idle air control valve connector at idle and check if engine condition is changed IAC VALVE CONNECTOR Try known good PCME and check if condition im- proves Daae F-144 - Yes ACTION Go to next step Check idle air control valve page F-106 Gartner Banana

TROUBLESHOOTING GUIDE F b AirIFuel mixture leaning when depressing accelerator Fuel injection control malfunction (Correction for accelerating condition) Air leakage of intake air system Fuel line Pressure low 22 park adbance control malfunction HESITATESISTUMBLES ON ACCELERATION 0 - STEF DESCRIPTION] Flat spot occurs just after accelerator depressed or mild jerking occurs during acceleration rrROUBLESHOOTlNG HINTS] ACTION INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 SELECT SWA SYSTEM SELECT 1 - Yes Go to next step No - Yes - No Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) uz page F-81 "88'1 flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 6 If OK, replace PCME page F-143 Q If not OK, check wiring between PCME and Self-Diagno- sis Checker US page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON Go to next step page F-95 SELECT SW A Lamp not ON/OFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Disconnect heated oxygen sensor connector and :heck if condition improves Yes - No - Yes -- -- Check heated oxygen sensor @s page F-156 Go to next step - :heck if PCME terminal voltages are OK :2M, 20, and 2Q) page F-146 Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") page F-148 Gartner Banana

TROUBLESHOOTING GUIDE ACTION Go to next step INSPECTION :heck if throttle linkage is correctly installed and 3perates freely - Yes - No - Yes - No - Yes - No Correct, clean, or replace as required any binding or dam- aged linkage and adjust cable deflection at throttle body @a page F-103 Go to next step :heck if air duct and air hoses are correctly nstalled page F-99 Repair ~8 page F-99 Go to next step ;heck for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg (17.7 inHg) VACUUM GAUGE Check for air leakage of intake air system components page F-100 :heck if air cleaner element is clean ttzr page F-76 Yes - No Go to next step Replace air cleaner element @a page F-99 >heck for correct ignition timing at idle page F-76 Yes - No Check if ignition timing advances when accelerating Q If advances, go to next step Q If no advance, replace PCME page F-143 Adjust page F-76 gnition timing: 10" a lo BTDC ;heck for correct fuel line pressure at idle page F-110 Yes - No - Yes Check if fuel line pressure decreases when accelerating quickly %el line pressure: 265-314 kPa I2.7-3.2 kgf/cm2, 38-46 psi] (Vacuum hose to pressure regulator discon- a If decreases, check fuel line and filter for clogging 0 If no decrease, go to next step Low pressure Check fuel line pressure while pinching fuel return hose If fuel line pressure quickly increases, check pressure regulator @a page F-118 0 If fuel line pressure gradually increases, check for clog- ging between fuel pump and pressure regulator If not clogged, check fuel pump maximum pressure page F-115 INSTALL CLAPS ;heck for EGR system malfunction page F-124 Repair or replace Go to next step Repair or replace t@~ page F-128 ;heck if exhaust system is restricted page F-128 Yes Go to next step Try known good PCME and check if condition im- )roves page F-144 Gartner Banana

TROUBLESHOOTING GUIDE PROUBLESHOOTING HINTS] 3 Air/Fuel mixture too lean or too rich Fuel injection control malfunction Air leakage of intake air system 23 Fuel line pressure low Fuel evaporative malfunction 0 Spark advance control malfunction -- SURGES WHILE CRUISING - STEP DESCRIPTION ( Unexpected change in engine speed which is usually repetitive INSPECTION ACTION - Yes - No - Yes - No Check if "00" is displayed on Self-Diagnosis check- er with ignition switch ON page F-79 Go to next step SELECTSW A SYSTEM SELECT 1 Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page ~-81 -- - "88" flashes Check PCME terminal 1 E voltage @i= page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME @ page F-143 o If not OK, check wiring between PCME and Self-Diagno- sis Checker US page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition Go to next step switch ON w page F-95 SELECT SW A Lamp not ONIOFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker @ page F-7 Disconnect heated oxygen sensor connector and check if condition improves Yes No - Yes Check heated oxygen sensor page F-156 Go to next step :heck if PCME terminal voltages are OK (1 R, 1 T, 2M, 20, and 2Q) as page F-146 Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") * page F-148 Gartner Banana

F TROUBLESHOOTING GUIDE INSPECTION ACTION Check if throttle linkage is correctly installed and operates freely Yes Go to next step Correct, clean, or replace as required any binding or dam- aged linkage and adjust cable deflection at throttle body r@ page F-103 Check for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg I17.7 inHg) VACUUM GAUGE / Yes Go to next step No - Yes Check for air leakage of intake air system components r@ page F-100 Go to next step Check if air cleaner element is clean page F-76 Replace air cleaner element page F-99 Check for correct ignition timing at idle page F-76 Yes - No Check if ignition timing advances when accelerating .I, If advances, go to next step o If no advance, replace PCME page F-143 Adjust r@ page M6 Ignition timing: 10" -r- lo BTDC Check for correct fuel line pressure at idle page F-110 Yes Check if fuel line pressure decreases when accelerating quickly Fuel line pressure: 265-314 kPa (2.7-3.2 kgf/cm2, 38-46 psi) (Vacuum hose to pressure regulator discon- nected) o If decreases, check fuel line and filter for clogging 0 If no decrease, go to next step No - Yes Low pressure Check fuel line pressure while pinching fuel return hose 0 If fuel line pressure quickly increases, check pressure regulator page F-113 0 If fuel line pressure gradually increases, check for clog- ging between fuel pump and pressure regulator If not clogged, check fuel pump maximum pressure page F-115 INSTALL CLAPS Repair or replace Check for EGR system malfunction page F-124 No - Yes - No Go to next step - -- Check if exhaust system is restricted page F-128 -- - Repair or replace So to next step Try known good PCME and check if condition im- 3roves page F-144 Gartner Banana

TROUBLESHOOTING GUIDE INSPECTION :heck for correct ignition timing at idle page F-76 gnition timing: 10" .t lo BTDC ;heck if spark plugs are OK RBON BUILDUP PLUG GAP 1 .O-l.lmrn b.040--0.043 in} DAMAGE AND DETERIORATION DAMAGE :heck if resistance of high-tension leads are OK lesistance: 16 k!2 per 1 m (3.28 ft) :heck if resistance of ignition coil is OK Section G lesistance (at 20°C (66°F)): Secondary coil ... 8.7-12.9 'heck for correct engine compression Section B ngine compression: 1,255483 kPa (12.8-9.0 kgf/cm2, 182-128 psiE.300 rpm Yes No Yes No - Yes Yes No - Yes - No ACTION Check if ignition timing advances when accelerating s, If advances, go to next step +, If no advance, replace PCME terminal voltages page F-143 Adjust page F-76 Go to next step Repair, clean, or replace us Section G Go to next step Replace w Section G Go to next step Replace Section G 30 to next step Zheck engine condition w Section B D Worn piston, piston rings or cylinder wall D Defective cylinder head gasket Distorted cylinder head Improper valve seating B Valve sticking in guide Gartner Banana

TROUBLESHOOTING GUIDE INSPECTION Run engine at idle and check if fuel line pressure is held after ignition switch turned OFF page F-109 Fuel line pressure: More than 147 kPa (1.5 kgflcm2,21 psi) for 5 min. PRESSURE IGNITION 5 MIN. TIME SWITCH OFF Disconnect each fuel injector connector at idle and check if engine speed decreases equally each time Yes - No Yes ACTION High pressure Check if vacuum hose to pressure regulator is damage or poorly connected 6 If OK, replace pressure regulator page F-1 0 If not OK, repair or replace hose Check fuel injector for fuel leakage ~8 page F-1 Go to next step Replace fuel injector a page F: Try known good PCME and check if condition im- mwes page F-144 FEO Gartner Banana

TROUBLESHOOTING GUIDE INSPECTION Check for correct ignition timing at idle t@= page F-76 Ignition timing: 10" +. lo BTDC Check if spark plugs are OK WEAR AND CARBON BUILDUP BURNS PLUG GAP 1 .+I .I mm (0.04C-O.043 in) DAMAGE AND DETERIORATION DAMAGE Check if resistance of high-tension leads are OK Resistance: 16 kR per lm {3.28 ft} Check if resistance of ignition coil is OK Section G Resistance (at 20°C {68"F)): Secondary coil ... 8.7-12.9 kC2 Check for correct engine compression Section 8 Engine compression: 1,255-883 kPa (12.8-9.0 kgf/cm2, 182-128 psi)-300 rpm :heck for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg (17.7 inHg) - Yes - No Yes - No - Yes - No - Yes - No - Yes - No - Yes ACTION Check if ignition timing advances when accelerating o If advances, go to next step o If no advance, replace PCME page F-143 Adjust page F-76 Go to next step Repair, clean, or replace Ojp Section G Go to next step ~eplace as? Section G Go to next step Replace Section G - -- Go to next step :heck engine condition I@= Section B B Worn piston, piston rings or cylinder wall B Defective cylinder head gasket B Distorted cylinder head B Improper valve seating B Valve sticking in guide Check for air leakage of intake air system components as? page F-1 00 Gartner Banana