1994 JEEP CHEROKEE flat tire

(18) Disconnect the charging hoses from the ser-
vice valves.
COMPRESSOR OIL LEVEL
The compressor oil level must be checked and ad-
justed if the system has been discharged rapidly, or
when a component has been replaced. If a replace-
ment compressor is being installed, it must be filled
with new compressor oil (Suniso 5GS, or equivalent).
The normal quantity of oil required for the com-
pressor and entire system is 136 ml (4.6 fluid oz.) for
SD 709 compressor. DO NOT overfill the compressor.
Excessive amounts of oil in the system will hinder
compressor operation and reduce A/C performance.
CAUTION: The compressor is a high speed unit.
Satisfactory operation is dependent on sufficient lu-
brication; however, excess oil will hinder A/C per-
formance.
Two oil level checking procedures are necessary.
Use Procedure (A) when the compressor is being re-
placed and the system was discharged properly (no
oil loss). Use Procedure (B) for routine maintenance
or when checking oil level after replacing a system
component.
In cases where rapid loss of refrigerant and oil
occurred, the system must be evacuated and
purged. Then the compressor must be filled with
the necessary amount of oil to fill the entire sys-
tem.
PROCEDURE A
(1) Remove the oil filler plug, discharge cap and
suction port caps from the original and replacement
compressor.
(2) Use a clean container to drain the oil from the
replacement compressor. Drain the oil through the
oil filler plug hole, the discharge and suction. Then
rotate clutch front plate several times to push the oil
on cylinder out to discharge chamber of cylinder
head and drain the oil from discharge port.
(3) Drain the oil from the original compressor into
a measuring cup or graduated beaker in the same
way as Step 2. Note the amount of oil drained.
(4) Fill the replacement compressor with the same
amount of oil drained from the original compressor
plus 30 ml (1 fluid oz.).
FOR EXAMPLE:ÐIf the old compressor contained
103.5 ml (3.5 fluid oz.) of oil, fill the replacement
compressor with a total of 133 ml (4.5 fluid oz.) of oil.
PROCEDURE B
(1) Start the engine and operate the engine at idle.
(2) Operate the air conditioning system for 10 min-
utes to return the maximum amount of oil in the sys-
tem to the compressor.(3) Stop the engine and disconnect the magnetic
clutch feed wire.
(4) Front-seat the discharge and suction service
valves.
(5) Determine the mounting angle.
(a) Position an Angle Gauge across the flat sur-
faces of the front mounting ears.
(b) Center the bubble.
(c) Read the mounting angle to the closest de-
gree.
(d) These vehicles should have 0É mounting an-
gle.
(6) Remove the oil filler plug. Position internal
parts by rotation of front plate counterweight to 30É
angle (Fig. 5).
(7) Insert the dipstick tool to its STOP position.
The Dipstick Tool is part of Tool Kit 7851. The stop
is the angle near the top of the dipstick. The bottom
surface of the angle must be flush with the surface of
the oil filler hole.
(8) Remove dipstick. Count increments of oil.
(9) Use mounting angle table to determine correct
oil level for the compressor (Fig. 6).
(10) If the increments read on the dipstick do not
match the table, add or subtract oil to the mid-range
value.
FOR EXAMPLE:ÐIf the mounting angle is 10É
and the dipstick increment is 3, add oil in 30 ml (1
fluid oz.) increments until 5 is read on dipstick.
(11) Check that the sealing O-ring is not twisted.
(12) Seat and O-ring must be clean.
Fig. 5 Check Oil Level
24 - 6 HEATING AND AIR CONDITIONINGJ

INTRODUCTION
CONTENTS
page page
DESIGNATIONS, LABELS/PLATES, CODES
AND DIMENSIONS..................... 1SPECIFICATIONS........................ 8
DESIGNATIONS, LABELS/PLATES, CODES AND DIMENSIONS
INDEX
page page
Engine and Transmission/Transfer Case Identification.3
International Vehicle Control and Display Symbols . 3
Major Component Identification............... 3
Tire Inflation Pressure Label................. 3
Vehicle Code Plate........................ 2Vehicle Designations....................... 1
Vehicle Dimension Data.................... 3
Vehicle Identification Number (VIN) Plate....... 1
Vehicle Load Data........................ 3
Vehicle Safety Certification Label............. 1
VEHICLE DESIGNATIONS
The Vehicle Designation Codes chart lists the vehi-
cle description(s) and the corresponding vehicle des-
ignation code for each type of Jeeptvehicle (Figs. 1,
2, and 3 ). The vehicle designation codes are different
from the Vehicle Identification Number (VIN) or
body-type/style codes.
VEHICLE SAFETY CERTIFICATION LABEL
A vehicle safety certification label (Fig. 4) is at-
tached to each Jeeptvehiclee. The label also lists
the:
²gross vehicle weight rating (GVWR) and the gross
front and rear axle weight ratings (GAWR's) based
on a minimum tire rim size and a maximum cold tire
inflation pressure;²month and year of vehicle manufacture;
²vehicle identification number (VIN);
²type of vehicle and
²month, day and hour (MDH) of final assembly.
The label is located on the driver's side door edge.
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE
The vehicle identification number (VIN) plate is at-
tached to the top left side of the instrument panel at
the base of the windshield. Each VIN contains 17 al-
pha-numerical characters. Refer to the decoding
chart to determine the actual identification of a
Jeeptvehicle.
VEHICLE DESIGNATION CODES
Fig. 1 YJÐWrangler Multi-Purpose Vehicle (With
Hard Top)
JINTRODUCTION1

If there is not enough space left in the row for all
of the 6-digit SEC code (if used):
²the unused space will remain blank, and
²the code will be listed in the next row.
The last nine positions of row 7 will contain a 2-digit
code, when applicable, and a 6-digit gateline serial
number (same as the last 6 numbers of the VIN).
The last code imprinted on a vehicle code plate will
be followed by the imprinted word END. When two
vehicle code plates are required, the last available
spaces on the first plate will be imprinted with the
letters CTD (for continued).
When a second vehicle code plate is necessary, the
first four spaces on each row will not be used because
of the plate overlap.
ENGINE AND TRANSMISSION/TRANSFER CASE
IDENTIFICATION
When required, refer to Group 9ÐEngines for allengine identification data. Refer to Group 21ÐTrans-
missions for all transmission/transfer case identifica-
tion data.
MAJOR COMPONENT IDENTIFICATION
When required, refer to the applicable service infor-
mation group for major component identification data.
TIRE INFLATION PRESSURE LABEL
The tire inflation pressures label is located on the
glove box door inside panel (Fig. 6). The tires should
also be inspected for visible wear. Also, inspect the
tires for cracks, bulges and other road hazard dam-
age. Refer to Group 22ÐTires And Wheels.
VEHICLE DIMENSION DATA
The vehicle dimension data charts list the exterior
and interior dimensions for each type of Jeeptvehicle.
VEHICLE LOAD DATA
The Vehicle Load Data chart lists the following in-
formation:
²the gross vehicle weight rating (GVWR),
²the gross axle weight ratings (GAWR),
²the cargo weight, and
²the passenger weight for each Jeepttype/body
style.
INTERNATIONAL VEHICLE CONTROL AND DISPLAY
SYMBOLS
Most of the graphic symbols illustrated in the fol-
lowing chart are used to identify various instrument
controls and displays.
Fig. 5 Vehicle Code Plate
VEHICLE CODE DECODING
Fig. 6 Tire Inflation Pressures LabelÐTypical
JINTRODUCTION3

ILLUMINATION LAMPS, INSTRUMENT
PANEL.............................8E-16
ILLUMINATION, RADIO/CLOCK.............8E-4
ILLUMINATION RELAY, RADIO.............8F-3
INDEX, GROUP; ELECTRICAL..............8A-1
INDEX, GROUP; INSTRUMENT PANEL
AND GAUGES........................8E-1
INDEX; WIRING DIAGRAMS XJ..........8W-149
INDEX; WIRING DIAGRAMS XJ-RHD.....8W-271
INDEX; WIRING DIAGRAMS YJ...........8W-73
INDEXES, WIRING DIAGRAM SHEETS......8W-1
INDICATOR, 4WD......................8E-22
INDICATOR, ANTI-LOCK..................8E-4
INDICATOR (BASE CLUSTER ONLY),
OPERATIONAL CHECK WITH BATTERY....8A-14
INDICATOR BEZEL REPLACEMENT.........8E-17
INDICATOR (CHECK ENGINE) LAMP FOR
DIAGNOSTIC TROUBLE CODES..........8A-19
INDICATOR INOPERATIVE, 4WD............8E-4
INDICATOR INOPERATIVE, BRAKE..........8E-4
INDICATOR INOPERATIVE, COOLANT
TEMPERATURE.......................8E-3
INDICATOR INOPERATIVE, LOW WASHER....8E-4
INDICATOR INOPERATIVE, OIL
PRESSURE..........................8E-3
INDICATOR INOPERATIVE, UPSHIFT........8E-4
INDICATOR LAMP, 4WD..................8E-2
INDICATOR LAMP, ANTI-LOCK BRAKE
SYSTEM (ABS).......................8E-2
INDICATOR LAMP, BRAKE; INSTRUMENT
PANEL AND GAUGESÐXJ...............8E-2
INDICATOR LAMP, BRAKE; INSTRUMENT
PANEL AND GAUGESÐYJ..............8E-16
INDICATOR LAMP (CHECK ENGINE),
MALFUNCTION; INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
INDICATOR LAMP (CHECK ENGINE),
MALFUNCTION; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
INDICATOR LAMP, COOLANT
TEMPERATURE.......................8E-1
INDICATOR LAMPÐPCM OUTPUT,
MALFUNCTION......................14-26
INDICATOR LAMP, UPSHIFT; INSTRUMENT
PANEL AND GAUGESÐXJ...............8E-2
INDICATOR LAMP, UPSHIFT; INSTRUMENT
PANEL AND GAUGESÐYJ..............8E-16
INDICATOR LAMPS....................8E-14
INDICATOR, OIL PRESSURE...............8E-1
INDICATORÐPCM OUTPUT, SHIFT........14-26
INDICATOR REPLACEMENTÐGEAR
SELECTOR...........................8E-6
INDICATOR, SEAT BELT..................8E-4
INDICATOR (SRI) LAMP, SERVICE
REMINDER..........................25-1
INDICATORS INOPERATIVE, GAUGES.......8E-3
INDICATORS, TREAD WEAR...............22-3
INFLATION PRESSURE LABEL, TIRE.....INTRO.-3
INFLATION PRESSURES, TIRE.............22-2
INITIALIZATION, SYSTEM POWER-UP.......5-43
INJECTION (MFI)ÐCOMPONENT
DESCRIPTION/SYSTEM OPERATION,
MULTI-PORT FUEL...................14-17
INJECTION (MFI)ÐCOMPONENT
REMOVAL/INSTALLATION, MULTI-PORT
FUEL..............................14-54
INJECTION (MFI)ÐGENERAL DIAGNOSIS,
MULTI-PORT FUEL...................14-32
INJECTOR DIAGNOSISÐVEHICLE RUNS
ROUGH AND/OR HAS A MISS
...........14-49
INJECTOR, FUEL
.......................14-55
INJECTOR TEST
.......................14-48
INJECTORSÐPCM OUTPUT, FUEL
.........14-25
INNER AXLE SHAFT OIL SEAL
REPLACEMENT
.......................2-33
INNER SCUFF PLATE/COWL SIDE TRIM
PANELÐXJ VEHICLES, FRONT
.........23-114
INNER SPLASH SHIELDS, FENDER
.......23-147
INOPERATIVE, 4WD INDICATOR
............8E-4
INOPERATIVE, ALL GAUGES
.............8E-22
INOPERATIVE, BRAKE INDICATOR
..........8E-4
INOPERATIVE, COOLANT TEMPERATURE
GAUGE
..............................8E-3
INOPERATIVE, COOLANT TEMPERATURE
INDICATOR
..........................8E-3INOPERATIVE, DIAGNOSINGÐTURN
SIGNAL.............................8J-2
INOPERATIVE, DIAGNOSISÐHAZARD
LAMPS..........................8J-1,8J-2
INOPERATIVE, DIAGNOSISÐTURN
SIGNAL.............................8J-1
INOPERATIVE, FUEL GAUGE...............8E-3
INOPERATIVE, GAUGES AND INDICATORS....8E-3
INOPERATIVE, LOW FUEL WARNING........8E-4
INOPERATIVE, LOW WASHER INDICATOR....8E-4
INOPERATIVE, OIL PRESSURE GAUGE......8E-3
INOPERATIVE, OIL PRESSURE
INDICATOR..........................8E-3
INOPERATIVE, ONE GAUGE..............8E-22
INOPERATIVE, SPEEDOMETER/
ODOMETER..........................8E-3
INOPERATIVE, TACHOMETER..............8E-3
INOPERATIVE, UPSHIFT INDICATOR........8E-4
INOPERATIVE, VOLTMETER...............8E-3
INPUT, AIR CONDITIONING (A/C)
CONTROLSÐPCM....................14-19
INPUT, AUTOMATIC SHUT DOWN (ASD)
SENSEÐPCM.......................14-19
INPUT, BATTERY VOLTAGEÐPCM.........14-19
INPUT, BRAKE SWITCHÐPCM............14-20
INPUT, CAMSHAFT POSITION SENSORÐ
PCM...............................14-20
INPUT, CRANKSHAFT POSITION
SENSORÐPCM......................14-20
INPUT, DATA LINK CONNECTORÐPCM.....14-20
INPUT, ENGINE COOLANT TEMPERATURE
SENSORÐPCM......................14-21
INPUT, EXTENDED IDLE SWITCHÐPCM....14-21
INPUT, IGNITION CIRCUIT SENSEÐPCM....14-21
INPUT, INTAKE AIR TEMPERATURE
SENSORÐPCM......................14-20
INPUT, LOSS OF SENSOR.................5-3
INPUT, MANIFOLD ABSOLUTE
PRESSURE (MAP) SENSORÐPCM.......14-21
INPUT, OXYGEN (O2S) SENSORÐPCM.....14-22
INPUT, PARK/NEUTRAL SWITCHÐPCM.....14-22
INPUT, POWER STEERING PRESSURE
SWITCHÐPCM......................14-22
INPUT, SCI RECEIVEÐPCM..............14-22
INPUT, SENSOR RETURNÐPCM..........14-23
INPUT SIGNALS, WHEEL/TIRE SIZE..........5-3
INPUT, SPEED CONTROLÐPCM..........14-23
INPUT, THROTTLE POSITION SENSOR
(TPS)ÐPCM........................14-23
INPUT, VEHICLE SPEED SENSORÐPCM....14-23
INSERTÐXJ VEHICLES, QUARTER
WINDOW GLASS/REAR QUARTER
PLASTIC...........................23-80
INSIDE LATCH RELEASE AND LOCK
RODS, DOOR........................23-57
INSIDE RELEASE AND LOCK HANDLE,
FULL-METAL DOOR LATCH............23-175
INSPECTION AND ADJUSTMENT,
PRELIMINARY......................21-167
INSPECTION AND DIAGNOSIS CHARTS.......6-4
INSPECTION, CALIPER CLEANING..........5-28
INSPECTION, CLEANING....21-13,21-204,21-305
INSPECTION, COMPONENT................5-8
INSPECTION, GEAR CLEANING...........19-40
INSPECTION, PRE-ALIGNMENT.............2-6
INSPECTION, TORQUE CONVERTER
STATOR CLUTCH....................21-189
INSPECTION, TRANSMISSION CASE
CLEANING.........................21-118
INSPECTION, VALVE BODY DISASSEMBLY
. . 21-138
INSPECTION, VISUAL
...................14-32
INSPECTION/MEASUREMENTS, FRAME
.....13-10
INSPECTIONS, STARTER SYSTEM
DIAGNOSTIC
.........................8A-9
INSTALLATION, 30RH/32RH
TRANSMISSION REMOVAL
............21-108
INSTALLATION, ACCELERATION SENSOR
....5-52
INSTALLATION, AW-4 TRANSMISSION
REMOVAL AND
.....................21-189
INSTALLATIONÐAX 15, TRANSMISSION
....21-35
INSTALLATION, BRAKE PEDAL
.............5-66
INSTALLATION, BRAKELIGHT SWITCH
.......5-66
INSTALLATION, CALIPER
.................5-30
INSTALLATION, CLUTCH COVER AND
DISC
...............................6-10INSTALLATION, CLUTCH HYDRAULIC
LINKAGE............................6-12
INSTALLATION, CLUTCH PEDAL............6-15
INSTALLATION, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE................2-43
INSTALLATION, DIFFERENTIAL; REAR
SUSPENSION AND AXLES...............3-24
INSTALLATION, DISC BRAKESHOE..........5-26
INSTALLATION, DRUM BRAKESHOE........5-34
INSTALLATION, FRONT WHEEL SENSOR.....5-49
INSTALLATION, MASTER CYLINDER....5-20,5-50
INSTALLATION, POWER BRAKE
BOOSTER.......................5-23,5-51
INSTALLATION, REAR WHEEL
SENSOR............................5-50
INSTALLATION, RING GEAR...............3-24
INSTALLATION, ROTOR..................5-30
INSTALLATION, TRANSFER CASE . . . 21-276,21-296
INSTALLATION, TRANSMISSION...........21-4
INSTALLATION, TRANSMISSION AND
CONVERTER.......................21-109
INSTALLATION, TRANSMISSION
AND TORQUE CONVERTER............21-190
INSTALLATION, TRANSMISSION VALVE
BODY.............................21-177
INSTALLATION, VALVE BODY............21-101
INSTALLATION, WHEEL..................22-6
INSTALLATION, WHEEL CYLINDER.........5-37
INSTALLATIONÐXJ, HCU.................5-54
INSTALLATION (XJ WITH FULL
CONSOLE), PARKING BRAKE LEVER.......5-60
INSTALLATION (XJ WITH MINI
CONSOLE), PARKING BRAKE LEVER.......5-58
INSTALLATION (XJ WITHOUT CONSOLE),
PARKING BRAKE LEVER................5-60
INSTALLATIONÐYJ, HCU.................5-54
INSTALLATION (YJ), PARKING BRAKE
PEDAL..............................5-61
INSTALLATION/ADJUSTMENT, IGNITION
SWITCH............................8D-31
INSTRUMENT CLUSTER.................8E-15
INSTRUMENT CLUSTER AND GAUGE
HOUSINGS
.........................23-190
INSTRUMENT CLUSTER BEZEL
.....23-91,23-191
INSTRUMENT CLUSTER BULB
REPLACEMENT
......................8E-19
INSTRUMENT CLUSTER DIAGNOSIS;
INSTRUMENT PANEL AND GAUGESÐ
XJ
.................................8E-3
INSTRUMENT CLUSTER DIAGNOSIS;
INSTRUMENT PANEL AND GAUGESÐ
YJ
................................8E-14
INSTRUMENT CLUSTER GAUGES;
INSTRUMENT PANEL AND GAUGESÐ
XJ
................................8E-13
INSTRUMENT CLUSTER GAUGES;
INSTRUMENT PANEL AND GAUGESÐ
YJ
................................8E-27
INSTRUMENT CLUSTER GENERAL
INFORMATION; INSTRUMENT PANEL
AND GAUGESÐXJ
....................8E-1
INSTRUMENT CLUSTER GENERAL
INFORMATION; INSTRUMENT PANEL
AND GAUGESÐYJ
...................8E-14
INSTRUMENT CLUSTER REPLACEMENT;
INSTRUMENT PANEL AND GAUGESÐ
XJ
.................................8E-5
INSTRUMENT CLUSTER REPLACEMENT;
INSTRUMENT PANEL AND GAUGESÐ
YJ
................................8E-17
INSTRUMENT CLUSTER SERVICE
PROCEDURES; INSTRUMENT PANEL
AND GAUGESÐXJ
....................8E-5
INSTRUMENT CLUSTER SERVICE
PROCEDURES; INSTRUMENT PANEL
AND GAUGESÐYJ
...................8E-17
INSTRUMENT CLUSTER/SWITCH/
LIGHTER/RADIO/HEVAC
................23-91
INSTRUMENT CLUSTERS
................8E-10
INSTRUMENT PANEL
.............23-93,23-190
INSTRUMENT PANEL AND GAUGESÐXJ
.....8E-1
INSTRUMENT PANEL AND GAUGESÐYJ
.....8E-1
INSTRUMENT PANEL COMPONENTS
......23-191
INSTRUMENT PANEL GAUGES
............8E-27
12 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

INSTRUMENT PANEL ILLUMINATION
LAMPS............................8E-16
INSTRUMENT PANEL LAMPS..............8E-4
INSTRUMENT PANEL REPLACEMENT.......8E-8
INSTRUMENT PANEL SERVICE..........23-192
INSULATION PANEL, DASH PANEL........23-95
INSULATOR PANEL, DASH PANEL.........23-11
INSULATOR PANEL, HOOD..............23-138
INTAKE AIR TEMPERATURE SENSOR......14-54
INTAKE AIR TEMPERATURE SENSORÐ
PCM INPUT.........................14-20
INTAKE AIR TEMPERATURE SENSOR TEST . . . 14-43
INTAKE DUCT, FRESH AIR...............24-41
INTAKE MANIFOLD.....................14-57
INTAKE MANIFOLDÐ2.5L ENGINE..........11-8
INTAKE MANIFOLDÐ4.0L ENGINE..........11-9
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR.......................8D-5,8D-27
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST.......................8D-14
INTAKE MANIFOLD LEAKAGE DIAGNOSIS.....9-5
INTERCHANGEABILITY, PARTS............21-66
INTERIOR COMPONENTS..........23-91,23-190
INTERIOR LAMPS......................8L-19
INTERIOR LAMPS, XJ..................8L-23
INTERIOR LAMPS, YJ..................8L-23
INTERIOR PAINT CODES, XJ............23-205
INTERIOR PAINT CODES, YJ............23-206
INTERIOR REARVIEW MIRROR...........23-74
INTERIOR REARVIEW MIRROR
SUPPORT BRACKET REPLACEMENT......23-75
INTERIOR TRIM PANELS AND SCUFF
PLATESÐXJ VEHICLES...............23-112
INTERLOCK CABLE ADJUSTMENT (XJ),
PARK........................21-97,21-186
INTERMEDIATE (COUPLING) SHAFT . . 19-21,19-43
INTERMITTENT WINDSHIELD WASHER,
DIAGNOSING........................8K-12
INTERMITTENT WIPER MODULE...........8K-5
INTERMITTENT WIPER WASHER..........8K-20
INTERNATIONAL VEHICLE CONTROL
AND DISPLAY SYMBOLS............INTRO.-3
IN-VEHICLE SERVICE, 30RH/32RH.........21-96
IN-VEHICLE SERVICE, AW-4.............21-173
ISOLATION, COMPRESSOR..............24-17
JACK STORAGEÐXJ VEHICLES..........23-127
JOINT ANGLE MEASUREMENT,
UNIVERSAL..........................16-4
JOINT REPLACEMENT, UNIVERSAL.........16-9
JOINTS, UNIVERSAL....................16-2
JOUNCE BUMPER, REAR................13-18
JUMP STARTING........................0-7
JUMP STARTING, HOISTING AND TOWING.....0-7
KEY LOCK CYLINDER, DOOR.............23-54
KEY LOCK CYLINDER, FULL-METAL
DOOR............................23-178
KEY LOCK CYLINDERS.............23-2,23-132
KEY WARNING SWITCH REPLACEMENT,
IGNITION............................8U-4
KEYLESS ENTRY.......................8P-8
KNOCK, LOW SPEED; FRONT
SUSPENSION AND AXLE................2-17
KNOCK, LOW SPEED; REAR SUSPENSION
AND AXLES...........................3-8
KNUCKLE AND BALL STUDS, STEERING.....2-30
LABEL, TIRE INFLATION PRESSURE.....INTRO.-3
LABEL, VEHICLE EMISSION CONTROL
INFORMATION (VECI)
..................25-1
LABEL, VEHICLE SAFETY CERTIFICATION
. INTRO.-1
LABELS/DECALS/PLATES
...........23-1,23-132
LABELS/PLATES, CODES AND
DIMENSIONS, DESIGNATIONS,
.......INTRO.-1
LAG TEST, TIME
......................21-169
LAMP, 4WD INDICATOR
..................8E-2
LAMP, ANTI-LOCK BRAKE SYSTEM (ABS)
INDICATOR
..........................8E-2
LAMP BEAM ADJUSTMENT, FOG
..........8L-12
LAMP, BRAKE INDICATOR; INSTRUMENT
PANEL AND GAUGESÐXJ
...............8E-2
LAMP, BRAKE INDICATOR; INSTRUMENT
PANEL AND GAUGESÐYJ
..............8E-16
LAMP BULB REPLACEMENT, BACK-UP/
REAR TURN SIGNAL/TAIL
...............8L-9
LAMP BULB REPLACEMENT, FRONT PARK/
TURN SIGNAL
........................8L-8LAMP BULB REPLACEMENT, SIDE
MARKER............................8L-7
LAMP BULB REPLACEMENT,
UNDERHOOD........................8L-18
LAMP BULB REPLACEMENTÐYJ
VEHICLES, HARDTOP DOME/CARGO.....8L-20
LAMP BULB/ELEMENT REPLACEMENT,
FOG ...............................8L-13
LAMP (CHECK ENGINE), MALFUNCTION
INDICATOR; INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
LAMP (CHECK ENGINE), MALFUNCTION
INDICATOR; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
LAMP (CHMSL)ÐXJ, CENTER HIGH
MOUNTED STOP.....................8L-10
LAMP (CHMSL)ÐYJ, CENTER HIGH
MOUNTED STOP.....................8L-11
LAMP, COOLANT TEMPERATURE
INDICATOR..........................8E-1
LAMP FOR DIAGNOSTIC TROUBLE CODES,
INDICATOR (CHECK ENGINE)...........8A-19
LAMP HOUSING, LIFTGATE LICENSE
PLATE .............................23-72
LAMP, I/P ASH RECEIVER TRAY..........23-92
LAMP, LICENSE PLATE..................8L-10
LAMP, LOW FUEL WARNING..............8E-2
LAMPÐPCM OUTPUT, EMR..............14-24
LAMPÐPCM OUTPUT, GENERATOR.......14-25
LAMPÐPCM OUTPUT, MALFUNCTION
INDICATOR.........................14-26
LAMP REPLACEMENT, DOME.............8L-20
LAMP REPLACEMENT, FOG..............8L-15
LAMP REPLACEMENT, UNDERHOOD.......8L-18
LAMP, SEAT BELT REMINDER............8E-16
LAMP SERVICE INFORMATION, DOME/
COURTESY.........................8L-19
LAMP SERVICE INFORMATION, FOG.......8L-12
LAMP SERVICE INFORMATION,
UNDERHOOD........................8L-17
LAMP, SERVICE REMINDER INDICATOR
(SRI)...............................25-1
LAMP SPEED CONTROL SWITCH TEST,
STOP...............................8H-7
LAMP SUPPORT BRACKET, I/P TWEETER
SPEAKER/COURTESY.................23-95
LAMP SWITCH REPLACEMENT, FOG.......8L-14
LAMP TROUBLE DIAGNOSIS, DOME/
COURTESY.........................8L-19
LAMP TROUBLE DIAGNOSIS, FOG.........8L-12
LAMP, UPSHIFT INDICATOR;
INSTRUMENT PANELAND GAUGESÐXJ....8E-2
LAMP, UPSHIFT INDICATOR;
INSTRUMENT PANELAND GAUGESÐYJ . . . 8E-16
LAMPÐYJ RENEGADE VEHICLES, FOG....23-150
LAMP/REAR WIPER SWITCHES, REAR
DEFOGGER/FOG......................8E-21
LAMPS, EXTERIOR......................8L-1
LAMPS, INDICATOR....................8E-14
LAMPS INOPERATIVE, DIAGNOSISÐ
HAZARD.........................8J-1,8J-2
LAMPS, INSTRUMENT PANEL.............8E-4
LAMPS, INSTRUMENT PANEL
ILLUMINATION......................8E-16
LAMPS, INTERIOR.....................8L-19
LAMPS OUT, DIAGNOSINGÐALL..........8E-16
LAMPS, XJ EXTERIOR..................8L-23
LAMPSÐXJ, HAZARD...................8J-1
LAMPS, XJ INTERIOR..................8L-23
LAMPS, YJ EXTERIOR..................8L-23
LAMPSÐYJ, HAZARD...................8J-2
LAMPS, YJ INTERIOR..................8L-23
LATCH ADJUSTMENT, DOOR.............23-55
LATCH AND RELEASE HANDLE,
TAILGATE..........................23-160
LATCH ASSEMBLY REPLACEMENT,
SOLENOID...........................8P-6
LATCH, DOOR.........................23-56
LATCH EXTERNAL RELEASE HANDLE,
FULL-METAL DOOR..................23-178
LATCH, FULL-METAL DOOR
.............23-179
LATCH, HOOD SAFETY
.................23-139
LATCH INSIDE RELEASE AND LOCK
HANDLE, FULL-METAL DOOR
..........23-175
LATCH RELEASE AND LOCK RODS,
DOOR INSIDE
.......................23-57LATCH RELEASE CABLE REPLACEMENT....23-10
LATCH REPLACEMENT, HOOD............23-10
LATCH STRIKER AND BUMPERÐXJ
VEHICLES, REAR SEATBACK...........23-111
LATCH STRIKER, HALF-METAL DOOR.....23-175
LATCH STRIKER REPLACEMENT, HOOD....23-10
LATCH STRIKER REPLACEMENT, SAFETY . . . 23-10
LATCH STRIKER, TAILGATE.............23-161
LATCH/KEY LOCK CYLINDER/STRIKER,
LIFTGATE...........................23-68
LEAD CORRECTION CHART...............22-5
LEAF SPRING; FRONT SUSPENSION AND
AXLE...............................2-14
LEAF SPRING; REAR SUSPENSION AND
AXLES............................3-3,3-6
LEAF SPRING EYE BUSHING
REPLACEMENT; FRONT SUSPENSION
AND AXLE...........................2-15
LEAF SPRING EYE BUSHING
REPLACEMENT; REAR SUSPENSION
AND AXLES........................3-4,3-6
LEAK DETECTION AND REPAIR, FIXED
GLASS WATER................23-83,23-189
LEAK DIAGNOSIS, CONVERTER HOUSING . . . 21-73
LEAK DOWN TEST, FUEL PRESSURE........14-7
LEAK TEST, REFRIGERANT................24-8
LEAKAGE DIAGNOSIS, GEAR
..............19-8
LEAKAGE DIAGNOSIS, INTAKE
MANIFOLD
............................9-5
LEAKAGE DIAGNOSIS, PUMP
..............19-8
LEAKAGE TEST, CYLINDER COMBUSTION
PRESSURE
...........................9-6
LEAKAGE TEST DIAGNOSIS, CYLINDER
COMBUSTION PRESSURE
................9-6
LEAKS, REPAIRING
.....................22-3
LEAKS, TESTING COOLING SYSTEM FOR
....7-18
LEFT HAND DRIVE, DRIVERS DOOR
POWER LOCK SWITCHÐ2-DOOR
.........8P-2
LEFT HAND DRIVE, DRIVERS DOOR
POWER WINDOW SWITCHÐ2-DOOR
......8S-6
LETTERS, JEEP BODY CODE
...............5-2
LEVEL AND CONDITION, CHECKING
FLUID
.......................21-96,21-173
LEVEL AND CONDITION, FLUID
...........21-69
LEVEL, BRAKE FLUID
....................5-13
LEVELÐBRAKELINES AND HOSES,
BRAKE BLEEDINGÐBRAKE FLUID
........5-13
LEVEL, CLUTCH FLUID
...................6-14
LEVEL, COMPRESSOR OIL
................24-6
LEVEL, CORRECT FLUID
.................5-48
LEVEL, TRANSFER CASE FILL
...........21-294
LEVELS, OPERATING SOUND
...............5-3
LEVER INSTALLATION (XJ WITH FULL
CONSOLE), PARKING BRAKE
............5-60
LEVER INSTALLATION (XJ WITH MINI
CONSOLE), PARKING BRAKE
............5-58
LEVER INSTALLATION (XJ WITHOUT
CONSOLE), PARKING BRAKE
............5-60
LEVER POSITIONS, TRANSMISSION
RANGES AND SHIFT
.................21-157
LEVER REMOVAL (XJ WITH FULL
CONSOLE), PARKING BRAKE
............5-59
LEVER REMOVAL (XJ WITH MINI
CONSOLE), PARKING BRAKE
............5-58
LEVER REMOVAL (XJ WITHOUT
CONSOLE), PARKING BRAKE
............5-60
LICENSE PLATE LAMP
..................8L-10
LICENSE PLATE LAMP HOUSING,
LIFTGATE
...........................23-72
LICENSE PLATE SCREW ANCHOR
AND BUMPER, LIFTGATE
..............23-72
LIFTGATE ADJUSTMENT
.................23-70
LIFTGATE GLASS, HARD TOP
............23-162
LIFTGATE GLASS WEATHERSTRIP SEAL
REPLACEMENT
.....................23-163
LIFTGATE HINGE
.......................23-67
LIFTGATE LATCH/KEY LOCK CYLINDER/
STRIKER
...........................23-68
LIFTGATE LICENSE PLATE LAMP
HOUSING
...........................23-72
LIFTGATE LICENSE PLATE SCREW
ANCHOR AND BUMPER
...............23-72
JINDEX13
Description Group-Page Description Group-Page Description Group-Page

PITMAN SHAFT SEALSÐIN CAR
REPLACEMENT......................19-21
PIVOT ASSEMBLY REPLACEMENT, FRONT
WIPER ARM.........................8K-9
PLANETARY GEAR AND CLUTCH
OVERHAUL, OVERDRIVE..............21-209
PLANETARY GEAR OVERHAUL, FRONT....21-228
PLANETARY GEAR TRAIN OVERHAUL.....21-131
PLASTIC COMPONENTS................23-203
PLASTIC DUCTS/HOSES/TUBING, RUBBER . . . 0-19
PLASTIC HOSES/TUBING, RUBBER.........0-28
PLASTIC INSERT ÐXJ VEHICLES, QUARTER
WINDOW GLASS/REAR QUARTER.......23-80
PLASTIGAGE, MEASURING WITH...........9-3
PLATE, FRONT SKID....................23-84
PLATE, FUEL TANK SKID; BODY
COMPONENTSÐXJ VEHICLES..........23-84
PLATE, FUEL TANK SKID; FRAME AND
BUMPERS..........................13-16
PLATE LAMP HOUSING, LIFTGATE
LICENSE...........................23-72
PLATE LAMP, LICENSE..................8L-10
PLATEÐLEAK TESTS, COMPRESSOR
VALVE ..............................24-8
PLATE REPLACEMENT, SUPPORT..........5-37
PLATE SCREW ANCHOR AND BUMPER,
LIFTGATE LICENSE...................23-72
PLATE SERVICE, DRIVE................21-109
PLATE SPECIFICATIONS, 30RH/32RH SNAP
RING/THRUST WASHER/THRUST.......21-322
PLATE THICKNESS, AW-4 CLUTCH DISC . . . 21-325
PLATE, TRANSFER CASE SKID; BODY
COMPONENTSÐXJ VEHICLES.....13-15,23-84
PLATE, VEHICLE CODE...............INTRO.-2
PLATE, VEHICLE IDENTIFICATION
NUMBER (VIN)....................INTRO.-1
PLATEÐYJ RENEGADE VEHICLES, FRONT
FASCIA AND SKID...................23-148
PLATEÐYJ RENEGADE VEHICLES, REAR
FASCIA AND SKID...................23-152
PLATE/COWL SIDE TRIM PANELÐXJ
VEHICLES, FRONT INNER SCUFF.......23-114
PLATESÐXJ VEHICLES, INTERIOR TRIM
PANELS AND SCUFF.................23-112
PLATESÐXJ VEHICLES, OUTER SCUFF....23-118
PLATFORM AND TRACKS, BUCKET SEAT . . . 23-105
PLUG ASSEMBLY REPLACEMENT,
ADJUSTER..........................19-27
PLUG CABLE RESISTANCE, SPARK........8D-18
PLUG, HOUSING END...................19-26
PLUG LOCATIONS, TRANSMISSION
SWITCH............................21-33
PLUG SECONDARY CABLES, SPARK . . 8D-17,8D-29
PLUGS, SPARK; IGNITION SYSTEMS . 8D-16,8D-28,
8D-33
PLUGS, SPARK; LUBRICATION AND
MAINTENANCE.......................0-18
POLISHING, BUFFING..................23-203
POSITION, HYDRAULIC FLOW IN MANUAL
FIRST GEAR (1)......................21-94
POSITION SENSOR, CAMSHAFT; FUEL
SYSTEM............................14-54
POSITION SENSOR, CAMSHAFT;
IGNITION SYSTEMS..............8D-1,8D-20
POSITION SENSOR, CRANKSHAFT; FUEL
SYSTEM............................14-55
POSITION SENSOR, CRANKSHAFT;
IGNITION SYSTEMS..............8D-2,8D-21
POSITION SENSORÐPCM INPUT,
CAMSHAFT.........................14-20
POSITION SENSORÐPCM INPUT,
CRANKSHAFT.......................14-20
POSITION SENSOR TEST, CAMSHAFT;
FUEL SYSTEM.......................14-43
POSITION SENSOR TEST, CAMSHAFT;
IGNITION SYSTEMS...................8D-8
POSITION SENSOR TEST, CRANKSHAFT;
FUEL SYSTEM.......................14-44
POSITION SENSOR TEST, CRANKSHAFT;
IGNITION SYSTEMS...................8D-9
POSITION SENSOR TEST, THROTTLE
......8D-18
POSITION SENSOR, THROTTLE
............8D-6
POSITION SENSOR (TPS)ÐPCM INPUT,
THROTTLE
..........................14-23
POSITION SENSOR (TPS) SERVICE,
THROTTLE
.........................21-184POSITION SENSOR (TPS) TEST, THROTTLE . 14-45
POSITION SENSOR (TPS), THROTTLE;
FUEL SYSTEM.......................14-59
POSITION SENSOR (TPS), THROTTLE;
IGNITION SYSTEMS..................8D-29
POSITION SWITCH, PARK/NEUTRAL;
BATTERY/STARTER/GENERATOR SERVICE . . 8B-6
POSITION SWITCH, PARK/NEUTRAL;
TRANSMISSION AND TRANSFER CASE . . 21-173
POSITION SWITCH SERVICE, PARK/
NEUTRAL..........................21-103
POSITION, SWITCH TEST WITH SWITCH IN
LEFT................................8T-3
POSITION, SWITCH TEST WITH SWITCH
IN RIGHT............................8T-3
POSITIONS, TRANSMISSION RANGES
AND SHIFT LEVER...................21-157
POWER BOOSTER CHECK VALVE TEST......5-11
POWER BOOSTER VACUUM TEST..........5-12
POWER BRAKE BOOSTER............5-22,5-40
POWER BRAKE BOOSTER INSTALLATION . . . 5-23,
5-51
POWER BRAKE BOOSTER OPERATION......5-22
POWER BRAKE BOOSTER REMOVAL....5-22,5-51
POWER BRAKE SYSTEM.................0-32
POWER BRAKES........................5-1
POWER BUCKET SEAT COMPONENTS.....23-106
POWER DOOR LOCKS..............8P-1,8P-10
POWER DOOR LOCKS, DIAGNOSING . . . 8P-1,8P-9
POWER GROUND......................14-22
POWER LOCK SWITCHÐ2-DOOR LEFT
HAND DRIVE, DRIVERS DOOR...........8P-2
POWER LOCK SWITCHÐ2-DOOR RIGHT
HAND DRIVE, DRIVERS DOOR...........8P-3
POWER LOCK SWITCHÐ4-DOOR,
DRIVERS DOOR......................8P-4
POWER MIRROR REPLACEMENT...........8T-4
POWER MIRROR SWITCH................8T-2
POWER MIRROR SWITCH REPLACEMENT....8T-4
POWER MIRROR SWITCH TESTING.........8T-2
POWER SEAT MOTOR REPLACEMENT......8R-2
POWER STEERING GEAR................19-73
POWER STEERING GEAR,
RECIRCULATING BALL................19-19
POWER STEERING GEAR SPECIFICATIONS . . . 19-34
POWER STEERING GEARS,
RECIRCULATING-BALL................19-69
POWER STEERING PRESSURE SWITCHÐ
2.5L ENGINE ONLY...................14-58
POWER STEERING PRESSURE SWITCHÐ
PCM INPUT.........................14-22
POWER STEERING PUMP......19-9,19-69,19-73
POWER STEERING PUMPÐINITIAL
OPERATION.........................19-13
POWER STEERING SYSTEM..............0-31
POWER STEERING SYSTEM DIAGNOSIS....19-3,
19-4,19-5,19-6,19-7
POWER WINDOW SWITCHÐ2-DOOR
LEFT HAND DRIVE, DRIVERS DOOR.......8S-6
POWER WINDOW SWITCHÐ2-DOOR
RIGHT HAND DRIVE, DRIVERS DOOR.....8S-7
POWER WINDOW SWITCHÐ4-DOOR,
DRIVERS DOOR......................8S-5
POWERTRAIN CONTROL MODULE (PCM)
60-WAY CONNECTOR.................14-38
POWERTRAIN CONTROL MODULE,
ELECTRICAL TESTS AT.................8H-6
POWERTRAIN CONTROL MODULE
(PCM); EMISSION CONTROL SYSTEMS....25-9
POWERTRAIN CONTROL MODULE
(PCM); FUEL SYSTEM............14-18,14-58
POWERTRAIN CONTROL MODULE
(PCM); IGNITION SYSTEMS
. . . 8D-6,8D-15,8D-28
POWER-UP AND INITIALIZATION, SYSTEM
. . . 5-43
PRE-ALIGNMENT INSPECTION
..............2-6
PRECAUTIONS, BRAKE SAFETY
.............5-2
PRECAUTIONS, CLUTCH SAFETY
...........6-10
PRECAUTIONS; PROPELLER SHAFTS
. . . 16-7,16-9
PRECAUTIONS, SAFETY, REFINISHING
.....23-200
PRECAUTIONS, SERVICE (A/C)
............24-2
PRELIMINARY BRAKE CHECK
..............5-7
PRELIMINARY CHECKS
...................7-5
PRELIMINARY CHECKS FIRST, SYMPTOM
AND ACTIONÐSEE
.....................7-6
PRELIMINARY DIAGNOSIS
...............21-69PRELIMINARY INSPECTION AND
ADJUSTMENT......................21-167
PREPARATION, SURFACE...............23-201
PRESSURE AND RETURN HOSE
REPLACEMENT.......................19-9
PRESSURE CAP, RADIATOR...............7-20
PRESSURE DIAGNOSIS..................24-9
PRESSURE GAUGE AND MANIFOLD
ASSEMBLY..........................24-2
PRESSURE GAUGE INOPERATIVE, OIL......8E-3
PRESSURE GAUGE, OIL..................8E-1
PRESSURE GAUGES.....................22-2
PRESSURE INDICATOR INOPERATIVE, OIL . . . 8E-3
PRESSURE INDICATOR, OIL...............8E-1
PRESSURE LABEL, TIRE INFLATION.....INTRO.-3
PRESSURE LEAK DOWN TEST, FUEL........14-7
PRESSURE LEAKAGE TEST, CYLINDER
COMBUSTION.........................9-6
PRESSURE LEAKAGE TEST DIAGNOSIS,
CYLINDER COMBUSTION................9-6
PRESSURE (MAP) SENSOR, MANIFOLD
ABSOLUTE; FUEL SYSTEM.............14-57
PRESSURE (MAP) SENSOR, MANIFOLD
ABSOLUTE; IGNITION SYSTEMS....8D-5,8D-27
PRESSURE (MAP) SENSORÐPCM
INPUT, MANIFOLD ABSOLUTE...........14-21
PRESSURE (MAP) SENSOR TEST,
MANIFOLD ABSOLUTE; FUEL SYSTEM....14-44
PRESSURE (MAP) SENSOR TEST, MANIFOLD
ABSOLUTE; IGNITION SYSTEMS........8D-14
PRESSURE REGULATOR, FUEL...........14-30
PRESSURE RELEASE PROCEDURE, FUEL....14-5
PRESSURE RELEASE PROCEDURE, FUEL
SYSTEM............................14-56
PRESSURE RELIEF/ROLLOVER VALVE . . . 25-5,25-9
PRESSURE RELIEF/ROLLOVER VALVE,
FUEL TANK....................14-15,14-56
PRESSURE SWITCHÐ2.5L ENGINE ONLY,
POWER STEERING...................14-58
PRESSURE SWITCHÐPCM INPUT,
POWER STEERING...................14-22
PRESSURE TEST, AIR...................21-73
PRESSURE TEST, CYLINDER COMPRESSION . . 9-5
PRESSURE TEST, FUEL SYSTEM......14-5,14-48
PRESSURE TEST, HYDRAULIC......21-71,21-168
PRESSURE TEST, PUMP.................19-3
PRESSURE TEST SPECIFICATIONS,
30RH/32RH........................21-323
PRESSURES, TIRE INFLATION.............22-2
PRIMER............................23-201
PRINTED CIRCUIT.....................8E-22
PRINTED CIRCUIT REMOVAL.............8E-24
PRINTED CIRCUIT REPLACEMENT.........8E-19
PRINTED CIRCUIT REPLACEMENTÐ
INSTRUMENT CLUSTER REMOVED.......8E-6
PROBLEM CAUSES, CLUTCH...............6-3
PROBLEMS, DIAGNOSING PARKING BRAKE . . 5-10
PROBLEMS, DIAGNOSING SERVICE BRAKE . . . 5-8
PROBLEMS, TROUBLESHOOTING WIRING . . . 8W-3
PROGRAMMING, TRANSMITTER...........8P-9
PROPELLER SHAFT REPLACEMENT.........16-7
PROPELLER SHAFTS....................16-1
PROPELLER SHAFTS AND U-JOINTS.......16-14
PROTECTION, STONE CHIP.............23-201
PROTECTOR STRIP, DOOR EDGE GUARD/
EDGE..............................23-61
PROTECTOR/NOZZLE, FUEL FILLER.......23-158
PULLEY REPLACEMENT, DRIVE...........19-11
PUMP AND PEDAL TRAVEL SENSOR
OPERATION, HCU.....................5-44
PUMP CAPACITY TEST, FUEL..............14-7
PUMP ELECTRICAL CONTROL, FUEL........14-5
PUMPÐINITIAL OPERATION, POWER
STEERING
..........................19-13
PUMP LEAKAGE DIAGNOSIS
..............19-8
PUMP MODULE, FUEL
..............14-2,14-56
PUMP, OIL
........................9-33,9-73
PUMP OPERATING SPECIFICATIONS
........19-3
PUMP OVERHAUL, OIL
..........21-122,21-206
PUMP, POWER STEERING
......19-9,19-69,19-73
PUMP PRESSURE TEST
..................19-3
PUMP RELAY, FUEL
....................14-56
PUMP RELAYÐPCM OUTPUT, FUEL
.......14-25
PUMP RELAY TESTING, FUEL
............14-44
PUMP REPLACEMENT
..................19-10
JINDEX17
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR TEST, ENGINE
COOLANT; FUEL SYSTEM..............14-43
TEMPERATURE SENSOR TEST, ENGINE
COOLANT; IGNITION SYSTEMS..........8D-12
TEMPERATURE SENSOR TEST, INTAKE
AIR ...............................14-43
TEMPERATURE SENSOR TEST, INTAKE
MANIFOLD AIR......................8D-14
TENSION, BELT.......................8B-10
TENSION, DRIVE BELT...............7-33,7-38
TENSIONÐRIGHT HAND DRIVE
(RHD),BELT..........................7-34
TENSION SPECIFICATIONS, BELT...........7-34
TENSIONER REPLACEMENT (XJ), PARKING
BRAKE CABLE........................5-61
TENSIONERÐXJ MODELS, AUTOMATIC
BELT ...............................7-36
TERMINAL ASSEMBLY REPLACEMENT,
CONNECTOR.........................8W-5
TERMINAL REPLACEMENT...............8W-5
TEST, A/C PERFORMANCE................24-8
TEST, ACTUATOR MOTOR STALL...........8P-6
TEST, AIR PRESSURE...................21-73
TEST, ANALYZING THE ROAD.............21-70
TEST, BATTERY LOAD...................8A-4
TEST, BATTERY OPEN CIRCUIT VOLTAGE....8A-3
TEST, CAMSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-43
TEST, CAMSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-8
TEST, CONVERTER STALL...............21-72
TEST, CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-44
TEST, CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-9
TEST, CYLINDER COMBUSTION
PRESSURE LEAKAGE...................9-6
TEST, CYLINDER COMBUSTION
PRESSURE LEAKAGE DIAGNOSIS..........9-6
TEST, CYLINDER COMPRESSION PRESSURE . . 9-5
TEST, ENGINE COOLANT TEMPERATURE
SENSOR......................8D-12,14-43
TEST, EXTENDED IDLE SWITCH...........14-45
TEST, FUEL PRESSURE LEAK DOWN........14-7
TEST, FUEL PUMP CAPACITY..............14-7
TEST, FUEL SYSTEM PRESSURE......14-5,14-48
TEST, HYDRAULIC PRESSURE......21-71,21-168
TEST, HYDROMETER....................8A-3
TEST, IDLE AIR CONTROL MOTOR........14-46
TEST, INJECTOR.......................14-48
TEST, INTAKE AIR TEMPERATURE SENSOR . . 8D-14,
14-43
TEST, MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR.................8D-14,14-44
TEST, MANUAL SHIFTING...............21-168
TEST, MASTER CYLINDER/POWER
BOOSTER............................5-11
TEST, OXYGEN SENSOR (O2S)
HEATING ELEMENT...................14-45
TEST, POWER BOOSTER CHECK VALVE......5-11
TEST, POWER BOOSTER VACUUM..........5-12
TEST PROCEDURES, BATTERY............8A-2
TEST PROCEDURES ON VEHICLE,
ENGINE STARTER MOTOR..............8A-9
TEST PROCEDURES ON VEHICLE,
GENERATOR........................8A-14
TEST, PUMP PRESSURE.................19-3
TEST, REAR WINDOW DEFOGGER GRID.....8N-1
TEST, REFRIGERANT LEAK................24-8
TEST, ROAD; TRANSMISSION AND
TRANSFER CASE.....................21-70
TEST, ROAD; VEHICLE SPEED CONTROL
SYSTEM............................8H-5
TEST SPECIFICATIONS, 30RH/32RH
PRESSURE........................21-323
TEST, SPEED CONTROL SWITCH (TURN
SIGNAL LEVER)......................8H-7
TEST, STARTER MOTOR RELAY...........14-48
TEST, STARTING SYSTEM COLD
CRANKING...........................8A-9
TEST, STOP LAMP SPEED CONTROL
SWITCH
............................8H-7
TEST, THROTTLE POSITION SENSOR
......8D-18
TEST, THROTTLE POSITION SENSOR
(TPS)
..............................14-45
TEST, TIME LAG
......................21-169TEST, TORQUE CONVERTER CLUTCH
RELAY.............................14-45
TEST, TORQUE CONVERTER STALL.......21-169
TEST, VACUUM SUPPLY.................8H-7
TEST, VEHICLE SPEED SENSOR......8H-5,14-45
TESTING, AUTOMATIC SHUTDOWN
(ASD) RELAY........................14-43
TESTING COOLING SYSTEM FOR LEAKS.....7-18
TESTING, FUEL PUMP RELAY............14-44
TESTING GENERAL INFORMATION,
BATTERY............................8A-3
TESTING, IGNITION SWITCH.............8D-30
TESTING, POWER MIRROR SWITCH........8T-2
TESTING, REAR WIPER/WASHER
SWITCH.......................8K-7,8K-14
TESTING, SWITCH; POWER SEATS.........8R-2
TESTING, SWITCH; POWER WINDOWS......8S-5
TESTING, SWITCH; REAR WINDOW
DEFOGGER..........................8N-2
TESTING, TRANSMISSION COOLER FLOW . . 21-106
TESTING, WIPER SWITCH...............8K-19
TESTS - (VOLTAGE DROP METHOD),
STARTER FEED CIRCUIT................8A-9
TESTS, ANTENNA.......................8F-9
TESTS AT POWERTRAIN CONTROL
MODULE, ELECTRICAL.................8H-6
TESTS AT SERVO, ELECTRICAL............8H-5
TESTS, COMPRESSOR VALVE PLATEÐ
LEAK...............................24-8
TESTS, IGNITION SWITCH CONTINUITY....8D-31
TESTS, OXYGEN SENSOR...............8D-19
TESTS, STARTER CONTROL CIRCUIT......8A-11
TESTS, VEHICLE SPEED CONTROL
SYSTEM............................8H-5
TESTS, WATER PUMP....................7-9
THERMOMETER AND SENSOR SYSTEM
REPAIR PROCEDURES.................8C-6
THERMOSTAT..........................7-13
THERMOSTAT, TEMPERATURE CONTROL . . . 24-35
THICKNESS, AW-4 CLUTCH DISC AND
PLATE ............................21-325
THICKNESS, DISC BRAKE ROTOR..........5-31
THICKNESS VARIATION, DISC BRAKE
ROTOR.............................5-31
THIRD GEAR (CONVERTER CLUTCH
ENGAGED), HYDRAULIC FLOW IN.......21-90
THIRD GEAR, HYDRAULIC FLOW IN D
RANGE.............................21-89
THREAD NOTATIONÐSAE AND METRIC . . INTRO.-9
THREADS, REPAIR DAMAGED OR WORN.....9-4
THROTTLE 3-2 DOWNSHIFT, HYDRAULIC
FLOW DURING FULL..................21-92
THROTTLE 3-2 DOWNSHIFT, HYDRAULIC
FLOW DURING PART..................21-91
THROTTLE BODY; FUEL SYSTEM.....14-29,14-59
THROTTLE CABLE.....................14-16
THROTTLE CABLE, ACCELERATOR PEDAL . . 14-16,
14-54
THROTTLE CABLE ADJUSTMENT,
TRANSMISSION.....................21-185
THROTTLE CABLE ADJUSTMENT,
TRANSMISSION......................21-98
THROTTLE CABLE REPLACEMENT,
TRANSMISSION.....................21-184
THROTTLE POSITION SENSOR............8D-6
THROTTLE POSITION SENSOR TEST.......8D-18
THROTTLE POSITION SENSOR (TPS);
FUEL SYSTEM.......................14-59
THROTTLE POSITION SENSOR (TPS);
IGNITION SYSTEMS..................8D-29
THROTTLE POSITION SENSOR (TPS)
SERVICE..........................21-184
THROTTLE POSITION SENSOR (TPS)
TEST..............................14-45
THROTTLE POSITION SENSOR (TPS)Ð
PCM INPUT.........................14-23
THROTTLE VALVE CABLE ADJUSTMENT,
TRANSMISSION......................21-70
TIE ROD ........................19-14,19-17
TIGHTENING, WHEEL NUT............5-32,5-37
TILT STEERING COLUMN................19-59
TIME LAG TEST
......................21-169
TIMING CASE COVER
................9-27,9-67
TIMING CASE COVER OIL SEAL
REPLACEMENT
...................9-26,9-67
TIMING CHAIN AND SPROCKETS
......9-28,9-68TIMING, IGNITION.....................8D-14
TIMING, VALVE.....................9-26,9-66
TIPS, TRANSMISSION ASSEMBLY........21-146
TIRE AND WHEEL BALANCE..............22-6
TIRE AND WHEEL RUNOUT...............22-8
TIRE CARRIER, EXTERNAL SPARE/WHEEL . 23-172
TIRE INFLATION PRESSURE LABEL.....INTRO.-3
TIRE INFLATION PRESSURES.............22-2
TIRE NOISE OR VIBRATION...............22-4
TIRE WEAR PATTERNS..................22-4
TIRES; LUBRICATION AND MAINTENANCE....0-34
TIRES................................22-1
TIRES, CLEANING OF....................22-2
TIRES, REPLACEMENT...................22-2
TIRE/WHEEL HOLDDOWN AND FLOOR
BRACKETS.........................23-128
TOOL, DRB SCAN; COOLING SYSTEM........7-5
TOOL, DRB SCAN; EMISSION CONTROL
SYSTEMS...........................25-2
TOOL, DRB SCAN; FUEL SYSTEM.........14-51
TOOL, DRB SCAN; IGNITION SYSTEMS.....8D-10
TOP REPAIR, HARD...................23-165
TOP ROOF VENT......................23-165
TOP SERVICE............23-164,23-166,23-167
TORQUE; COOLING SYSTEM..............7-39
TORQUE; FUEL SYSTEM................14-62
TORQUE; IGNITION SYSTEMS............8D-33
TORQUE, COLLISION DAMAGE............13-1
TORQUE CONVERSION..............INTRO.-10
TORQUE CONVERTER; TRANSMISSION
AND TRANSFER CASE...........21-66,21-158
TORQUE CONVERTER CLUTCH RELAY......14-60
TORQUE CONVERTER CLUTCH RELAY
TEST..............................14-45
TORQUE CONVERTER CLUTCH RELAYÐ
PCM OUTPUT.......................14-27
TORQUE CONVERTER INSTALLATION,
TRANSMISSION.....................21-190
TORQUE CONVERTER REMOVAL,
TRANSMISSION.....................21-189
TORQUE CONVERTER STALL TEST.......21-169
TORQUE CONVERTER STATOR CLUTCH
INSPECTION.......................21-189
TORQUE SPECIFICATIONS, 30RH/32RH....21-323
TORQUE SPECIFICATIONSÐ AX 15
MANUAL TRANSMISSION.............21-320
TORQUE SPECIFICATIONSÐACCESSORIES . 23-208
TORQUE SPECIFICATIONS, AW-4
.........21-331
TORQUE SPECIFICATIONS, BATTERY
.......8B-10
TORQUE SPECIFICATIONS; BATTERY/
STARTER/GENERATOR SERVICE
.........8B-12
TORQUE SPECIFICATIONS, BRAKE
..........5-67
TORQUE SPECIFICATIONS; CLUTCH
........6-17
TORQUE SPECIFICATIONS; ELECTRICAL
.....8A-8
TORQUE SPECIFICATIONS; ENGINES
....9-49,9-89
TORQUE SPECIFICATIONS; EXHAUST
SYSTEM AND INTAKE MANIFOLD
........11-10
TORQUE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE
................2-47
TORQUE SPECIFICATIONS; HEATING AND
AIR CONDITIONING
...................24-45
TORQUE SPECIFICATIONS; HORNS
.........8G-3
TORQUE SPECIFICATIONS;
INTRODUCTION
...................INTRO.-8
TORQUE SPECIFICATIONS, NP231/NP242
. . 21-331
TORQUE SPECIFICATIONS; PROPELLER
SHAFTS
............................16-14
TORQUE SPECIFICATIONS; REAR
SUSPENSION AND AXLES
...............3-50
TORQUE SPECIFICATIONS, STARTER
MOTOR
............................8B-11
TORQUE SPECIFICATIONS; STEERING
......19-73
TORQUE SPECIFICATIONS XJ
.............8K-7
TORQUE SPECIFICATIONSÐXJ VEHICLES
. . 23-207
TORQUE VALUES, STANDARD
.........INTRO.-9
TOW HOOKÐXJ VEHICLES, REAR
.........23-87
TOW HOOKS
..........................13-14
TOW HOOKS, FRONT
....................13-5
TOWING, JUMP STARTING, HOISTING
.......0-7
TOWING RECOMMENDATIONS
..............0-8
TRACK BAR
....................2-10,2-13,3-6
TRACKS, BUCKET SEAT PLATFORM
.......23-105
TRAC-LOK DIFFERENTIAL
................3-44
JINDEX23
Description Group-Page Description Group-Page Description Group-Page