1994 JAGUAR XJ6 torque

Automatic Transmission (AJl6)
. Ensure the shift lever is in 'N'.
. Fit and fully seat a new rotary switch to the transmission
unit.
Fit but do not fully tighten the rotary switch securing nuts.
. Fitand align ServiceTool JD161 (Fig.l)tothe rotaryswitch
. Finallytorque tighten the rotary switch securing nuts.
Displace and remove Service Tool JD161.
. Reposition and fit the rubber sealing plug to the switch.
. Reconnect the transmission unit multi-pin plug.
. Reposition the harness and feed the multi-pin plugs and
. From below the vehicle, reposition the harness 'P' clip to
. Fit and tighten the 'F" clip securing nut.
. Align the harness 'P' clip to transmission shift abutment
Fit and tighten the 'P' clip securing screw.
. Fit and align the rotary switch protection cover; fit and
torque tighten the securing bolts.
. From inside the vehicle, fit the grommet in the correct
orientation and reposition the harness in the correct posi
-
tion.
to
align the switch rotor to the switch body.
grommet through the tunnel aperture.
its mounting stud.
bracket.
. Reconnect the rotary switch harness multi-pin plugs.
. From below the vehicle, ensure that there is no excess
slack
in the switch harness that could foul the propshaft.
. Lower the vehicle on the ramp.
Reposition and fit the tunnel carpet.
Using suitabletiestraps,securethe harnesstotheconsole
= Fit and fully seat the veneer panel to the console; fit and
harness.
tighten the wing nuts.
Fit and fully seat the shift lever surround.
multi-pin plug and fully seat the switch.
Connect the Performance Mode switch to the harness
Fit and align the console veneer panel rear finisher.
9 Place the ashtray assembly in position.
= Reconnect the cigar lighter / illumination harness con-
nectors.
Reposition and
fit the ashtray assemb1y;fit and tighten the
securing screws.
. Close the armrest lid.
Reconnect the battery
Fia. 1
Issue 1 August 1994 10 X300 VSM

Automatic Transmission (AJl6)
8.1.6 TRANSMISSION FLUID FILTER, RENEW
SRO 44.24.07
9 Raise the hood and fit a fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
. Removethefluid pan,seeSub-section8.1.7 (4,OL)orSub-
. Release and remove the fluid filter securing screws; dis-
. Remove and discard the filter '0' ring.
. Clean the new filter and mating faces.
. Fit the '0' ring to the new filter; fit and seat the filter assem-
. Fit and torque tighten the filter securing screws.
. Refitthefluidpan,seeSub-section8.1.7 (4,OL)orSub-sec-
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Subsection
8.1.2.
Remove the fender cover and lower the hood.
(3,2L AND 4,011
tion 8.1.2.
section
8.1.8 (3,2L).
place and remove the fluid filter.
bly to the valve body.
tion 8.1.8
(3,2L).
8.1.7 FLUID PAN, RENEW (4,OL)
SRO 44.24.04
. Raise the hood and fit a fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
tion 8.1.2.
Release and remove the rotary switch protection cover to
fluid pan securing screws; remove the rotary switch
protect ion cover.
Release and remove the fluid pan securing bolts and
clamps
(1 Fig. 1). Displace and remove the fluid pan
(2 Fig. 1).
. Drain the fluid pan. Remove and discard the fluid pan
gasket if the gasket is damaged.
Remove the magnets from the fluid pan and place the fluid
pan aside.
. Clean the gasket faces and magnets.
Fit a serviceable gasket to the new fluid pan.
. Fit the magnets in position in the fluid pan.
Fit and align the fluid pan to the transmission unit; fit and
torque tighten the fluid pan clamps and securing bolts.
. Fit the rotary switch protection cover to the fluid pan
bosses and fit and torque tighten the rotary switch protec-
tion cover securing bolts.
. Lower the vehicle on the ramp.
Refill the transmission unit with fluid, see Subsection
Remove the fender cover and lower the hood.
8.1.2.
Fig. 1
X300 VSM 11 Issue 1 August 1994

Automatic Transmission (AJ16)
8.1.8 FLUID PAN, RENEW (3,2L)
SRO 44.24.04
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
tion 8.1.2.
Release and remove the fluid pan securing bolts and
clamps
(1 Fig. 1).
. Displace and remove the fluid pan (2 Fig. 1).
= Drain the fluid pan. Remove and discard the fluid pan
. Remove the magnetsfrom the fluid pan and place the fluid
. Clean the gasket faces and magnets.
. Fit a serviceable gasket to the new fluid pan.
. Fit the magnets in position in the fluid pan.
9 Fit and align the fluid pan to the transmission unit.
Fit the fluid pan clamps; fit and torque tighten the fluid pan
. Lower the vehicle on the ramp,
. Raise the hood and fit a fender cover.
. Refill the transmission unit with fluid, see Sub-section
. Remove the fender cover and lower the hood.
gasket
if the
gasket is damaged.
pan aside.
securing bolts.
8.1.2.
8.1.9
SRO 44.24.05
. Raise the hood and fit a fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
FLUID PAN GASKET, RENEW (3,2L)
tion 8.1.2.
. Release and remove the fluid pan securing bolts clamps
. Displace and remove the fluid pan (2 Fig. 1).
(1 Fig. 1).
Remove and discard the fluid pan gasket.
pan aside.
. Removethe magnetsfrom the fluid pan and place thefluid
. Clean the fluid pan, gasket faces and the magnets.
. Fit a new fluid pan gasket.
. Fit the magnets in position in the fluid pan.
9 Fit and align the fluid pan to the transmission unit, fit the
fluid pan clamps,fit and torquetighten the fluid pan secur-
ing bolts.
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Sub-section
. Remove the fender cover and lower the hood.
8.1.2.
/>U492
Fig. 1
Fig. 1
j
X300 VSM Issue 1 August 1994 12

Automatic Transmission (V12 & AJ16 Supercharged) Powortrain
Fixing
Drain plug to fliud pan
Fluid pan
to case
Pressure control solenoid bracket
to valve body
Solenoid to valve body
Speed sensor and bracket assembly to case
Valve body
to case 1 lubrication pipe
Valve body to case
I PSM
1. SERVICE TOOLS & EQUIPMENT
No Jaguar service tools are required for the operations covered by this Sub-section.
lightening Torque
(Nm)
34
24
8
8
11
11
11
Description
Tivoli Kay Adhesives No. 5696
sealant
UseS Notes
Exhaust system joints
Description
I To be issued I I
Data
Issue 1 August 1994 ii X300 VSM

Automatic Transmission (V12 & AJl6 Supercharged) Pomrtrain
8.2.1 GENERAL DESCRIPTION
This section provides information relating to the Powertrain 4L80-E transmissions fitted to the 4,O liter supercharged
engine (4,OL SC) and to the 6,O liter engine (6,OL).
The Powertrain 4L80-E is a four-speed, high torque capacity, electronically controlled automatic transmission, which
comprises a torque converter with lock-up direct drive clutch and three planetary gear sets. Five multiple diskclutches,
one intermediate sprag clutch assembly, two roller clutch assemblies and two band assemblies provide the drive el- ements necessary for correct sequential gear engagement and operation.
The torque converter containing
a pump, a turbine (rotor), a stator assembly, and a clutch pressure disksplined to the
turbine, acts as a fluid coupling for smooth torque transmission from the engine. The converter also supplies addi- tional torque multiplication when necessary, and the torque converter clutch (TCC) pressure disk provides a mechan- ical direct drive or 'lock-up' above a certain speed in top gear for greater fuel economy.
Gearshift operations are controlled from the Transmission Control Module (TCM), which governs the electronically
controlled valve body situated within the transmission.
Three planetary gear sets provide reverse and the four forward ratios, the changing of which is fully automatic in rela
- tion to load, vehicle speed and throttle opening. The Transmission Control Module receives and integrates various ve- hicle sensor input signals, and transmits operating signals to the solenoids located in the control valve assembly.
These solenoids govern the transmission operating pressures, up-shift and down-shift gear selection patterns and
also the torque converter clutch operation by pulse width modulated control.
8.2.1.1 Gear Ranges
Selectable gear positions are: P - Park, R - Reverse, N - Neutral, D - Drive, 3, 2.
P - Park position of the shift lever provides a mechanical locking of the output shaft of the transmission, and as such,
must only be engaged when the the vehicle is stationary. In addition, and for
extra safety, the handbrake should also
be applied. It is necessary to have the ignition ON and the footbrake applied to move the shift lever from the Park
position. For ignition key removal the shift lever must be in the Park position. The engine can be started in the Park
position.
R - Reverse enables the vehicle to be operated in a rearwards direction. The engine cannot be started in the Reverse
position.
N
-Neutral position enables the engine to be started and operated without driving the vehicle. It also allows the vehicle
to be moved manually for access, ie for removal of the propeller shaft.
D
-Drive position allows the automatic selection of all four forward gear ratios during normal driving conditions for
maximum efficiency and fuel economy. On acceleration, down-shifts are obtained by depressing the accelerator pedal
or by manual selection. The engine cannot be started in this position.
3
- Manual third position allows automatic operation of the three lower gear ratios but inhibits selection of the fourth
ratio. This position is used for towing a trailer or negotiating hilly terrain when greater engine braking control is re- quired. The engine cannot be started in this position.
2 - Manual second position allows automatic operation of the two lower gear ratios but inhibits selection of the third
and fourth ratios. This position is used for heavy traffic congestion or negotiating hilly terrain when even greater en
- gine braking control is required than is provided by manual third. This ratio may be selected at any vehicle speed - even if the transmission is in third or fourth ratio, the transmission will immediately down-shift to second gear pro- vided the vehicle speed is below 137 km / h (85 mile / h). The engine cannot be started in this position.
N.g!b: With the Performance Mode switch in the NORMAL position, the vehicle will pull away in second gear. How- ever, if more than 75 per cent of throttle is applied when the vehicle speed is between zero and 13 km/ h (8 mile / h), then first gear will be selected. From 13 to 61 km/ h (8 to 38 mile/ h) first gear is obtainable by 'kick-down'.
In 'sport' mode thevehicle pulls away in first gear and the transmission operatesfully in all four forward gears.
X300 VSM 1 Issue 1 August 1994

Automatic Transmission (V12 & AJ16 Supercharged) Powertrain
1.
2.
3.
4.
5. 6.
7.
8.
9. 10.
11.
12.
13.
Torque converter
Turbine shaft
Pressure disk
Converter turbine
Converter stator
Variable force motor
solenoid
Fluid pan
Filter
Interior detent lever
Manual shaft
Control valve
Front band
Parking lock actuator
3 4667 i JU-134
14.
15.
16.
17.
18.
19.
20. 21.
22.
23.
24. 25.
Rear band
Sun gear shaft
Sun gear
Parking lock pawl
Transmission case
Output shaft
Rear extension housing
Rear internal gear
Output planetary carrier
assembly Reaction planetary
carrier assembly
'LO' roller clutch
Main shaft
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
Intermediate clutch Intermediate sprag clutch
Direct clutch
Forward clutch
Overdrive planetary carrier
assembly
Overdrive roller clutch
Overrun clutch
Fourth clutch
Pump assembly
Converter pump
Stator roller clutch
Output speed sensor
Fig.1 Powertrain 4L8O-E automatic transmission
0
0
0
Issue 1 August 1994 2 X300 VSM

Powertrain Automatic Transmission (V12 & AJ16 Supercharged)
Light throttle D1 -D2 D2 - D3 D3 - D4
Normal mile 1 h 8- 10 18-20 25 - 39
kmlh 13- 15 28 - 33 40 - 46
sport mile 1 h 10 - 12 20 - 23 30 - 34
kmlh 16- 19 32 - 37 48-55
Up to Detent D1- D2 D2 - D3
Normal mile I h 34 - 37 60-66
kmlh 54 - 59 97 - 107
8.2.1.2 Shift Speeds
0
D4 - TCC on
45 - 51
72
-83
47
- 55
76
-88
D3
- D4
86
-94
138
- 151
4,O Liter Supercharged
sport mile I h 43 - 47 74 - 81 103 - 113
kmlh 69 - 76
118- 130
166 - 182
Maximum shift speeds (through detent)
Normal 1 Sport mile I h
kmlh
D1 -D2 D2 - D3 D3 - TCC on
47 - 50 81 -84
116 - 128
75
- 80 130 - 134
187 - 205
TCC
-Torque converter clutch
m: Road speeds shown above are for a vehicle with an axle ratio of 3,58:1, and standard tyres (2251 65ZR15). For
a vehicle with optional sports tyres
(225 / 55ZR16) (lattice wheels), these speeds must be reduced by 2,4%.
Zero throttle 1 TCCoffinD4 1 D4 - D3 D3 - D2
X300 VSM 3 Issue 1 August 1994
D2 - D1
Normal mile 1 h
kmth
sport mile 1 h
kmlh
I 36 - 40 15- 17
10- 12 -
58-64 24 - 27 16- 19 -
36 - 40 18 - 20 12 - 14
9-9
58-64 29 - 32 20 - 22 14 - 15
Up to
detent D4 - D3 03 - D2
Normal mile 1 h 67-74 3-44
kmlh 107-118 63-70
sport mile 1 h 81 -89 57 - 63
kmlh 130- 144 92 - 101
Kick-down available (through detent) TCC4 - D3 D3 - 02
Normal 1 Sport mile I h 103- 113 67 -74
kmlh 165 - 183 107 - 118 D2
- D1
9-9
14
- 15
27
- 29
43 - 47
D2
- D1
36 - 40
58-64

Automatic Transmission (V12 & AJ16 Supercharged)
Light throttle D1 -D2
Normal mile 1 h -
km/h -
sport mile / h 10- 12
kmlh 16- 18
Up to detent
Normal mile I h
kmlh
sport mile
1 h
km/h
Maximum shift speeds (through detent)
Normal I Sport mile / h
kmlh
6,O Liier
D2 - D3
D3 - D4
D4 - TCC on
20 - 23 29 - 33
48 - 55
32
- 37 46 - 52
77 -88
23 - 26 32 - 37 51 -59
36
- 41 51 -59 82 - 94
D1 -D2
D2 - D3 D3 - D4
35
- 40 61 -70 83-91
56
- 64 98- 112 133 - 164
43 - 49 73 - 79 99 -107
68
-78 117 - 127 158 - 172
D1 -D2 D2 - D3
D3 - TCC on
48-53 81 -89
116- 124
77
- 85 130- 149
186 - 198
Zero throttle
Normal mile 1 h
kmlh
sport mile
1 h
km/h
TCC off in 04 D4 - D3 D3 - D2 D2 - D1
- 36 - 40 15 - 17 10 - 12
16
- 19 58 - 64 24 - 27
36
- 40 18 - 20 12-14 6-7
58
- 64 29 - 32 19 - 22 10- 12
-
0
0
Up to detent
Normal mile I h
kmlh
sport mile
/ h
km/h
mile I h
kmlh
'Kick-down' available (through detent)
Normal 1 Sport
TCC -Torque converter clutch
m: Road speeds shown above are for a vehicle with an axle ratio of 3,58:1, and standard tyres (2251 65ZR15). For
a vehicle with optional sports tyres
(225 155ZR16) (lattice wheels), these speeds must be reduced by 2,4%.
D4 - D3 D3 - D2 D2 - D1
67 - 75 37 - 41 7-9
108
- 119 59 - 66 11 - 14
84
-92 60 - 66
27 - 29
134
- 148 96 - 106
43 - 47
TCC4
- D3 03 - D2 D2 - D1
103 - 113 67 -75 36 - 40
164
- 181 108 - 119 58 - 64
0
0
Issue 1 August 1994 4 X300 VSM