1994 HONDA INTEGRA boot

Slave Cylinder
Removal/lnstallation
CAUTION:
a Do not spill brake tluid on the car. it may damago tho
paint; it brake tluid doos conlacl tho paint, wash it
off immediately with watei.
a Plug tho €nd of the clutch pipe with a shop lowsl to
plevcnt b.ake fluid from coming out.
-61, Super High Temp Urea Grease {P/N
08798-9002).
: Brake Assembly Lube or equivalent rubber
grease.
Disconnect the clutch pipe from the slave cylinder.
Remove the slave cylinder from the clutch housing.
'1.
BOOTRemove and check for signs ol leaking and deterioration.
Install the slave cylinder in the reverse order ol
removat.
NOTE: Make sure the boot is installed on the slave
cylinder.
CLUTCH PIPE15 N.m (1.5 kgf.m, 11 lbf'ftl
SLAVE CYLINOER
-90021-Cl
tP/N 08798
8 x 1.25 mm22 N.m 12.2 kgl'm,16 rbt'ft)
4.
:^....:: Gil^lt i
(Brake A$embryLubol
Bleed the clutch hydraulic system.
a Attach a hose 1o the bleeder screw, and suspend
the hose in a container oJ brake fluid.
a Make sure there is an adequate supply of tluid at
the clutch master cylinder. then slowly pump the
clutch pedal until no more bubbles appear at the
bleeder hose.
a Refill the clutch master cylinder with fluid when
done.
a Use only DOT 3 or 4 brake tluid.
12-6

spection
release fork boot trom the clutch4. Torque the mounting bolts in a crisscross pattern as
shown. Tighten the bolts in several steps to prevent
warping the diaphragm spring.
8 x 1.25 mm25 N.m 12.6 kgt'm,19 tbt.ftl
2. Remove the release tork trom the clutch housing by
squeezing the release fork set spring with pliers. Re-
move the release bearing.
Check the release bearing for play by spinning it by
hand.
CAUTION: The release boaring i6 packed with
grease. Do not wash it in solvent.
Remove the special tools.
Recheck the diaphragm spring fingers tor height (see
page 12-7]..
Release Bearing
Removal/ln
1. Remove the
housing.
CLUTCH HOUSING
RELEASE FORK
-24/--2,t'.2424?'
IJ
l{ there is excessive plaY, rep)ace the rdease\Ear-
ing with a new one.
,F=:=

Release Bearing
Installation
1.With the release tork slid between the release bear-
ing pawls, install the release bearing on the main-
shaft while inserting the release fo.k through the hole
in the clutch housing.
Align the detent ot the release fork with the release
tork bolt, then press the release fork over the release
fork bolt.
NOTE; Use only Super High Temp Urea G.ease (P/N
08798- 9002).
2.
-611
lPlN 08798-
-6
{P/N 0879a-9002)
Move the release fork right and left to make sure that
the fork tits properly against the release bearing, and
that the release bearing slides smoothly.
4. lnstall the release fork boot.
12-12

12 N.m (1.2 kgim,9 lbnft)
15 N.m (1.5 kgnm, 11 lbf.ft)
15 N.m (1.5 kgf.m, 11 lbf.ft)
24 N.m (2.4 kgf.m, 17 lbf'ft)
27 N.m (2.8 kgnm,20 lbnft)
30 N.m (3.1 kgf.m, 22 lbf'ft)
Bolt Size
,l
{
@@69
@
@@@@@@@@6Dq0
o€xv0@
@0!@@@@al
61@
B
c
D
E
F
6x1.0mm
6x1.0mm
I x 1.0 mm
8 x 1.25 mm
8 x 1.25 mm
8 x 1.0 mm
i) BALL BEARINGe sroPPER R|NG9 TAPER RINGA NEEDLE EEARINGO SPACER.d SYNCHRO RINGt sYNcHRo SPR|NG!) 5TH/REVEFSE sYNcHRo SLEEVEO 5TH/REVERSE SYNCHRO HUB[0 sYrucxao nlrucii i) 5TH GEARO 38 x 43 x 26 mm NEEDLE BEARINGt3 SPACEE COLLARO 4TH GEAR.iB SYNCHRO FING.Ii9 SYNCHRO SPRING{, 3RD/,ITH SYNCHRO HUB
@ 3RD/4TH SYNCHBO SLEEVEt9 3RD GEARO MAINSHAFTO wasHER@) SPRING WASHER40 BALL BEARINGO 28 x 41 x ? mm OIL SEAL Replace.ad 35 x 56 x 8 mm OIL SEAL Replace.a0 14 x 20 mm OOWEL PIN@ OIL CHAMBER PLATE'A BEVERSE IDLEN GEAR SHAFT@ wasHER t-2).A REVERSE IDLER GEAFO REVERSE CHANGE HOLDER3A sTH/REVERSE SHIFT PIECEO 1ST/2ND SHIFT FORK04 3RD/.TH sHlFr FoRK@ 5TH/REVERSE SHIFT FORKO9' OIL GUTTER PLATE6' SNAP RING@ 72 mm THRUST SHIM) OIL GUIOE PLATEi!0 10 mm WASHER Replace..4i] REVERSE IDLER GEAR SHAFT BOLT54 N.m {5.5 kgt m, 40lblftl) TRANSMISSION HANGER B(3 BREATHER CAP@ TRANSMISSION HANGER A63 BACK.UP LIGHT SWITCH25 N.m (2.5 ksf.m, 18lbfftl@r 14 mrn waSHER Replace.67 16 mm SEALING BOLT29 N.m (3.0 kgl.m, 22 lbf ft)@ 32 mm SEALING BOLT25 N.m (2.5 kgf.m. 18lbt'ft|@ 40 x 62 x 9 mm OIL SEAL Replace.D STEEL BALL D. 5/16 inGl SPRING L. 30 mm {1.2 in}
@ 12 mm WASHER Replace.63) SET SCREW22 N.m 12.2 kgl.m, 16 lbt'ft,@ OIL ORAIN PLUG39 N.m {4.0 kgt.m, 29 lbf'ftl€9 WASHER Replace.@ oIL FILLER PLUG4,1N.m 14.5 kgJ m, 33 lblftl
*1:81881 engine*2:B18Cl engine
WASHER Beplace.TRANSMISSION HOUSING80 mm SHIM (*1)79.5 mm SHIM {*21THRUST SHIM {*2IT. 2.0 mm (0.079 in)BEARING OUTER RACE {*2}SHIFT PIECE SHAFTINTERLOCKSHIFT PIECESHIFT ARM HOLDERSELECT ARMSELECT RETURN SPRING10 mm SHIM10 mm WASHERLOCK COLLAR3 x 16 mm SPRING PIN Replace.8 mm SPRING WASHERCHANGE PIECESET SCREW22 N.m {2.2 kgf.m, 16 lbf.ft}SPRING L.25.6 mm {1.01 inlSTEEL BALL D. 5/16 inMAGNETCLUTCH HOUSING14 x 25 x 16 mm OIL SEAL Replace.SHIFT RODDIFFERENTIAL ASSEMBLYSee section 15BEARING OUTER RACE I*2ITHRUST SHIM I*2)T. 2.5 mm (0.098 in,SHIFT ROD BOOTOIL GUID€ PLATE33 x 60 x 20 mm NEEDLE BEARINGBEARING RETAINER PLATELOCK WASHER Replace.COUNTERSHAFTTHRUST SHIM37 x 42 x 25 mm NEEDLE BEARINGlST GEARFRICTION DAMPERSYNCHRO RINGSYNCHRO SPRINGlST/2ND SYNCHRO HUBREVERSE GEARDOUBLE CONE SYNCHRO I*2ISYNCHRO BING I*1)FRICTION DAMPERSPACER42 x 6? x 24 mm NEEDLE BEARING2ND GEAR3RD GEAR4TH GEAS5TH GEARNEEDLE BEARINGBALL BEARINGSPRING WASHERLOCKNUT Replace.108 - 0- 108 N.m(11.0 - 0* 11.0 kgt m,80- 0- 80lbf.ft)5 x 22 mm SPRING PIN Replace.00
13-9

Shift Rod
CHANGE PIECE
SPRINGL 25.6ll.0r in,
STEEL AALL(D.5/16
SPRING WASHER
Removal
1. Remove the shift rod boots.
2. Romove the change piece sttaching bolt and the
spring washer.
3. Remove the set screw, then remove the spring and
the steol ball.
4. Remov€ tho shitt rod, then remove the chsngepiece.
5. Remove th€ oilseal.
OIL SEALRoploc€.
*q
ACHING BOLT
SET SCBEW
13-18

Transmission
;
ReassemblV
1. lnstallthe new oil seal.
2. Set the change Piece.
3. lnstall the shift rod.
4 Installthe steel ball, the spring, and the set screw.
5. lnstall the change piece attaching bolt.
6. Install the shift rod boots.
8x1.0mm30 N.m 13.1 kg{ m.
SET SCREW12 x'1.0 mm22 N.m {2.2 kg{.m, 16lbl.ft}
SPRINGL. 25.6 mm22 tbl.ltl
Installthe oil chamber Piate.
SHIFT ROD
6x1.0mm12 N.m (1.2 kgt'm,9lbtft)
9.
10.
8. Install the differential assembly.
DIFFERENTIALASSEMBLY
Set the spring washer and the washer.
Install the mainshaft, the countershaft, and the shift
fork assemblies.
NOTE: Align the finger ot the interlock with the
groove in the shift fork shaft.
MAINSHAFT
COUNTERSHAFT
SHIFT FORKS
(cont'd)
13-41

Transmission Assembly
1. Inst€llthe dowel pins on the clutch housing.
2. Apply grease to the parts as shown, then install the
release fork and release beaaing.
NOTE: Use only Super High Temp Urea Grease(P/N 08798 - 9002).
3. Install the release fork boot.
lnstallation
22 tbt-ttl
BELEASE FORK BOLT29 N.m (3.0 kgl.m,tPlN 08798 - 90021
RELEASEBEARING
@
I
{P/N 08798 - 90021
Place the transmission on the transmission iack,
and raise it to the engine level.
Install the transmission mounting bolts and the rear
mount bracket bolts sELF-LocKrNG BoLT
RELEASE REEASEFORK FORKBOOT
12 x 1.25 mm6it N.m 16.5 kgl.m, 47 lbf.ftl
Replace.14 x 1.5 mm
13-46
6, Raise the transmission, then install the transmission
mounI.
NOTE: Torque the mounting bolt and nuts in the
sequence shown.
CAUTION: Check that the bushings are not twistod
or offset,
O 12 x 1.25 mm54 N.m {6.5 kgt m,47 tbtfrl
7. Install the three upper transmission mounting
and lower starter motor mounting bolt.
bolts
10 x 1.25 mm44 N.m lil,s kgt m,33 tbf.ftl
@ 12 x 1.25 mm7,1 N.m 17.5 kg{.m,5/r lbtftl
12 x 1.25 mm64 N.m 16.5 kgf.m, 47 lbf.ftl

8, Instsll the right tront mounvbracket.
SELF.LOCKING BOLTReplac€.12 x 1.25 mm
10 x 1,25 mmil a N.m (i4.5 kgf..n,33 tbtftl
9. Installthe clutch cover.
6r1.0mm12 N.m 11.2 kgtm,9 rbf.ftl
12 x 1.25 mm57 N.m ls.E kgf.m,a:I lbl.trll818Bl .ngin.l
8 x 1.25 mm2il N'm 12.4 kg{.m,17 tbffrt
RIGHT
10.lnstall the tront
stiff€nsrs.
(818C1 engine) and rear engine
8 x 1.25
12 x 1.25 mm5t N.tn {5.842 tbt ftt
24 N.m l2.a kgf.]n,17 tbtftl
8 x 1.25 mm
22 N.rn 12.2 kgl-m.16 tbtftl
FROifT ENGINE 2r N'm (2.4 kg['m,
SnFFENERS 17lbf.ttl
lBl8Cl lngin.l
11. Installthe change rod, the spring pin, and the clip.
NOTE:
12 x 1.25 ftm5? N.rn l5.E kg[.m,42 tbl.ft)
sHtFT ROO aOOt
2MqlL#--7
HOt.C(cont'dl
. Install the clip and the spring pin on the
joint as shown.
. Turn the shift rod boot so the hole is
down as shown.
. Make sure the shift rod boot is installed
cnange roo,
12. Install the change extension.
13. Installthe heat shield (818C1 engine).
8 x 1.25 mm
change
facing
on the
CHANGE ROD
CHANGEEXTENSION
5xl.0mm9.8 N.m 11.0 kgt'm,7 tbf.ftt
/^ "-*
i@
CLIP
. SPRING PINl3- Replace.
I e -- nrr,l
ll'--PuNcH
HEAT SHIELD(B18Cl .nginol
13-47