1994 HONDA INTEGRA transmission

Transmission
NOTE:
a Coat all parts with ATF.a Replace the parts below:. O-rings. Lock washers. Gaskets. Locknuts. Conical spring washers. Sealing washers
TOROUE: 12 N.m (1.2 kgt.m, 8.7 tbf.fr)
LOCK-UP VALVEEODY
OOWEL PINS, 2
COOLER CHECK VALVE
Reassembly
Bolts,4
DOWEL PINS. 2
MAIN VALVE
OIL FEED PIPE
/ LUBRTcAToR
, PLATE
fln /
| / /""n
v{*' e'f _\
_! 1.-...-]]
-. :-,.
OOWEL PINS, 2
orLFEEDPIPES
OIL FEED PIPES
ACCUMULATOB COVER
OIL FEED PIPE
Bolts,3
e
"o't
CONTROL
E SHAFT
LOCK WASHER
SERVO DETENTBASE
REGULATOR VALVEBODY
OIL FEED PIPES
SERVO BODY
SERVO SEPARATORPLATE
EoDY | . "1-
OIL PUMP DRIVEN
GEAR SHAFT
OIL PUMP DRIVEN GEAR
MAIN S€PARATORPLATE
SECONDARY VALVEBODY
DOWEL PINS, 2
SECONDARY SEPARATORPLATE
vaLVE spRtNGS \_(< \
ToRou E coN vE RTE n \-\.--CHECK VALVE ----.-. --'r -
Bolt
14-156
ATF MAGNET

Transmission
12 x '1.25 fifi64 N.m {6.5 kgt'm,47 tbt'tr)
CONNECTOR STAY
Reassembly (cont'dl
TRANSMISSIONHANGER
TRANSMISSIONMOUNT BBACKET
MAINSHAFTSUB-ASSEMBLY
TRANSMISSION HOUSINGMOUNTING BOLTS, 18l0 x 1.25 mm
fl
44 N.m (4.5 kgl.m. 33 lbf.trl
TRANSMISSION HOUSING
T=
TRANSMISSION HOUSINGGASKETReplace.
REVERSE GEAR COLLAR
NEEOLE BEARING
REVEBSE GEAR
LOCK WASHERReplace.
SHIFT FORK
REVERSE SELECTORDOWEL PINS, 3
COUNTERSHAFTSUB.ASSEMBLY
DIFFERENTIALASSEMBLY
TOROUE CONVERTERHOUSING
14-158

18. Install the sub-shaft assembly in the transmission
housing {see page 14-138).
19- Install the reverse idler gear and gear shatt holder
(see page 14-154).
20. Install the differential assembly in the torque con-
verter housing.
21. Install the mainshaft and countershaft sub-assembly
together in the torque converter housing.
MAINSHAFTSUB.ASSEMBLY
COUNTERSHAFTSUB.ASSEMBLY
22.Turn the shift fork so the large chamtered hole is fac-
ing the fork bolr hole. then installthe shift fork with
the reverse selector and torque the lock bolt. Bend
the lock tab against the bolt head.
SHIFT FORK
LOCI( WASHERReplace.
6 x 1.0 mm4 N.m(1.4 kgl.m, rO lbt.ft)
Large chamfered holefaces this way.
,,1
24.
lnstall the reverse gear with the collar and needle
bearing on the countershalt.
Align the spring pin of the control shaft with the
transmission housing groove by turning the control
shalt.
Place the transmission housing on the torque con-
verter housing with a new gasket and the dowel pins.
CONTROL
/K"\
//2"\TRANSMISSION HOUSING
Install the transmission housing bolts along with the
t.ansmission hanger and the connector stay, then
torque the bolts in two or more steps in the sequence
shown.
TOROUE: 44 N.m (4.5 kgf.m, 33 lbf'ft)
TRANSMISSIONHANGER
25.
CONNECTOR
14-159

Transmission
Reassembly (cont'dl
SUB-SHAFT
27. Slip the special tool onto the mainshaft as shown.
MAII{SHAFT HOLDERoTGAa - PF5010I
Install the parking b.ake lever on the control shaft.
Installthe mainshaft 1st g6ar collar and thrust wash-
er on the mainshaft.
Install the countershaft 1st gear collar and n6€dls
bearing, then install the count€rshatt 1st gear/one-
way clutch/parking gea, assembly on the coun-
tershalt.
Install the parking b.ake pawl in th€ transmission
housing, then engage it with the parking gear.
PARKI''IG GEAR
PARTI GARAKELEVER
24.
29.
30.
31.
lST CLUTCH
14-1 60
MAIt{SHAFTCOU TERSHAFT
32. Use th6 old locknut and old conicsl spring washot
to tighten th€ parking gear to th€ sp€cifi€d torque,
then loosen the locknut.
TOROUE: 103 .m (1O.5 kgf.m, 75.9 lbf'ftl
NOTE: Locknut has left-hand threads.
PARKII{G GEAR
Install the sub-shaft lst gear on thg sub-shaft.
Install new O-rings on the mainshaft.
NOTE: Wrap the shaft splines with tspa to prevont
damago to the O-rings.
Assemblo th€ thrust wash6r, thrust naedle bearing,
needle bearing and msinshsft lst gear on tho lst
clutch assombly, then install them on the mainshaft.
33.
34.

36. Align the hole of the sub-shaft 1st gear with the hole
of the transmission housing, then insert a pin to lock
the sub-shaft while tightening the sub-shaft locknut.
37. Installnew conicalspring washers and new locknuts
on each shaft.
CAUTION: Install the conical spdng washers in the
dilection shown.
38. Tighten the locknuts to the specified torque.
TOROUE:
MAINSHAFT 93 N.m (9.5 kgf'm, 69 lbf.ft)
COUNTERSHAFT 103 N.m(1O.5 kgf.m, 75.9 lbf.ft)
SUB-SHAFT 93 N.m (9.5 kgf.m. 69 lbf.fi)
NOTE: Mainshalt and countershaft locknuts have
left-hand threads.
CONICAL DISC SPRINGSlnstall in rhis direcrion.
39.Stake each locknut using
. MAINSHAFT
a 3.5 mm punch.
. COUNTERSHAFT
O,7- 1.2 mm
0.7- 1.2 mm1O.03-O.05 in)
SUB-SHAFT LOCKNUT
14-161

Transmission
Reassembly (cont'dl
40. Set rhe parking brake lever in the E position, thenverify that the parking brake pawl engages the park-
Ing gear.
41. lf thepawldoes notengagefully, checkthe parking
brake pawl stopper clearance as described on page
14-1 54.
42. Tighten the lock bolt and bend the lock tab.
10 tbf.frl
PARKING GEAR
Install the right side cover and right side cover pro
lecror.
TOROUE: 12 N.m {1.2 kgf.m, 8.7 lbf.ftl
6x 1.0 mm
PARKING BRAKE PAWL
14-162
44. Install the throttle control leverwiththe lever springon the throttle control shaft.
TOROUE: 7.8 N.m (O.8 kgf.m, 5.8 tbf.ft)
45. Install the tramsmission mount bracket.
TOROUE: 64 N.m (6.5 kgf.m, 47 lbf.trl
46. Install the ATF cooler pipes and ATF level gauge.

Transmission
Installation
1. Flush the ATF cooler as described on pages I4-168
thru 'l 69.
2. Install the starter motor on the transmission hous-
ing, then installthe l4 mm dowel pins in the torque
converrer nousrng.
STARTER MOTOR
O-RINGReplace.14 mm OOWEL PINTOROUECONVERTER
J.
TRANSMISSION HOUSINGMOUNTING BOLTS
59 N.m 16.0 kgf.m,43 lbl.ftl
Place the transmission on a transmission jack, and
raise to the engine level.
Attach the transmission to the engine, then install
the transmission housing mounting bolts and two
rear engine mounting bolts with new washers.
REAR ENGINEMOUNT BOLTS14 x 1.5 mm
45 N.m 14.5 kgf'm,
'14 mm DOWEL PIN
I
i.'l,i;
14-164
5. Install the transmission mount.
6. Install the transmission
12 x 1.25 mm64 N.m 16.5 kgl.m, 47 lbf.ft)
12 x 1.25 mm74 N.m 17.5 kgf'm,54 rbt'ft)
housing mounting bolts.
MOUNTING BOLTS12 x 1 .25 rnm74 N.m (7.5 kgf'm, 54 lbf.ftl
TRANSMISSION HOUSING

7.Remove the transmission jack.
Attach the torque converter to the drive plate with
eight bolts and torque:
Rotate the crankshatt as necessary to tighten the
bolts to 1/2 of the specilied torque, then to the final
toaque, rn a cnsscross pattern.
After tighten the last bolts, check that the crankshaft
rotates freely.
TOROUE: 12 N.m {1.2 kgl.m.8.7 lbf.ft}
Install the torque converte. cove. and engine
stiffener.
L
9.
6 r 1.O mm12 N.m 11.2 kgt.m, 8.7 lbl.ltl
10.
12 N.m 11.2 kgf.m,8.7 rbt.ft)
Tighten the crankshaft pulley bolt to specified
rorque.
TOROUE: 177 N.m {18.O kgt.m, 130 lbf'ft}
10 x 1.25 mm44 N'm {4.5 kgf.m.33 rbt'frl
8 x '1.25 mm24 N.m (2.4 kgl.m,17 tbf.trl
lO x '1.25 mm43 N.m14.4 kgf.m, 32 lbf.ltl
11. Connect the ATF cooler hoses to the joint pipes.
12. Connect the throttle control cable to the throttle con-
trol lever and install the right front mount/bracket.
THROTTLE CONTROL LEVERTHROTTLE CONTROLCABLE END
JOINT PIPES
12 x 1 .25 mm64 N.m {6.5 kgf.m,47 tbf.ftlReplace.
ATF COOLER HOSES10 x 1.25 mm RIGHT44 N.m (4.5 kgf'm, FRONT33 rbl.ftl MoUNT/BRACK€T
t5.Install the control lever with a new lock washer to
the control shalt. then install the shift cable cover.
CAUTION: Take care not to bend the shift cable.
CONTROLSHAFT
SHIFT CABLE
CONTROL LEVER
6 x 1.0 mm12 N.m{1.2 kgf.m,8.7 lbl.rr)
SHIFT CABLECOVER
LOCK6 x 1.0 mm14 N.m 11.4 kgl.m,10 lbf.fr)
(cont'dl
Replace.ASHER
14-165