1994 HONDA INTEGRA alternator belt

ll
il
Standards and Service Limits
ElectricalSection 23
*1: Do not adiust the gap, replace spark plug it it is out of spec.*2r When using a new belt, adjust d€tl€ction or tension to new valu€s. Run tho engine lor 5 minutes thon turn it off.Readiust de{lection or tension to usod belt values.
MEASUREMENTSTANDARD {NEWI
lgnilion coilRat€d voltago VPrimary winding resistance at 58'F (20'C) OSecondary winding resistance 6t 68'F (20"C) kO0.6 - 0.812.4 - 19.2
lgnition wireResistance ar 68"F (20'C) k025 max.
Spark plugTvpeGap B18Bl engineB18Cl engine
STANDARD INEW}SEN$CE UM]T
See Section 231.0 - 1.1 {0.039 - 0.043}1.3 {0.051)rl
lgnition timingAt idling" BTDC (Red)- rpmM/T16" r 2. -750 r 50 (Neurra0
16" t 2" -750 r 50 |!]or L?.lposition)Alternator b€lt'2Deflecrion wilh 98 N {10 kgf,22lbllbetween pulleys9.0 - 11.0 (0.35 - 0.43) with us6d b6li6.0 - 8.0 {0.24 - 0.31} with new b6lt
Eelt t€nsion N (kgf, lbf)Measured with belt tension gsuge340 - 490 {35 - 50, 77 - 110) with used bolt690 - 880 {70 - 90, 154 - 198} with now boh
AlternatorOurput l3.5 V at hot ACoil resistance (rotor) at 68"F {20"C} 0Slip ring O.D.Brush lengthErush spring tonsion N (kgt, lbf)
STANDARD INEWISENUCE UMTT
902.914.4 t0.57)r0.5 (0.41)
3.210.33, 0.73)
tnn ro.rrr1.5 (0.06t
StanerOutputMica depthCommulatot runoutCommutator O.D.Brush lengthBrush spring tension (new) N lkgt, lbf)
0.5 - 0.8 (0.02 - 0.03)0 - 0.02 (0 - 0.0008)29.9 - 30.0 (1.177 - 1.r81)15.0 - 15.5 (0.s9 - 0.61)17.7 - 23.5 fi.8 - 2.4,4.0 - 5.3)
0.2 (0.0081
0.05 t0.@2)29.0 (1.142)
10.0 (0.39)

Insrall the left front mount, then tighten the bolts in
the numbered sequence as shown (O-@),
O 12 x 1.25 ]n]n83 N.m 18.5 kst.m,61 lbt.ftlReplace.
@ 12 r 1.25 mm59 N.m {6.0 kgl.n,43 tb{.ftlReplace.
@ 10 r 1.25 mm44 N.m (4.5 kgf.m, 33 lbt.ftl
k-
5-15
a Check that the sp.ing clip on the end of each
driveshaft clicks into place.
GAUTION: Uso oow spring clips.
a Bleed air trom the cooling system at the bleed bolt
with the heater valve open (see page 10-5).
a Adjust the th.ottle cable (see section 1 1).
a Check the clutch pedal tree play lsee section 12).
a Check that the transmission shifts into gear
smoothlv,
a Adiust the tension of the following drive belts.
Alternator belt {s€e section 23).
P/S pump belt {see section 17).
A/C comoressor belt (see section 22).
a Inspect tor fuel leakage (see section 1 1).
. After assembling fuel line parts, turn on the ig-
nition switch (do not operate th€ starter) so
that the Juel pump operates for approximat€-
lV two seconds and the tuel line pressurizes.
Repeat this operation two or three times and
check for fuel leakage at any point in the fuel
line.
(cont'd)

Timing Belt
lllustrated Index
NOTE:
. Refer to page 6-12 for positioning crankshaft and pulley before installing belt.
. Mark the direction of rotation on the belt before removing.
. Replace the rubber seals tor oil leakag€ between the cylinder head and cover.
a Do not uss the middle cover and lower cover for storing itsms disassembled.
. Clean the middle cover and lower cover before installation.
CAP NUT6xl.0mm9.8 N'm (1.0 kgf.m,7.2lbtft) WASHER
\oReplaco when damagedor deteriorated.
6x1.0mm
CYLINDER HEAD COVERRefer to pago 6-31 wheninstalling.
RUBBER SEALSReplace when damagedor deleriorsled.
BACK OOVER
lnstallwith concavesurface facing in.Clean.
8 x 1.25 mm37 N.m 13.8 kgl.m,27 lbf'ft)
AD.'USTING BOLT10 x t.25 mm5/r N.m 15.5 kgl.m, ,o lbtft)For adjustrnent only,do not r€move,
BOLT
COVER
6x1.0mm9.8 N'm (1.0 kg{.m. t.2 lbf.tt}
9.8 N,m 11.0 kg{.m,7.2 lbl.frl
Adlustment, pago 6-9Replacement, page 6"10
TIMIMi BELTInspection, page 6-9ALTERNATORBELTAdjustm6nt,Soction 23
CRANKSHAFTPULI"EYRomov6 any oiland clgaa on thgtiming bolt guideplato side.
TIMING BELTDBIVE PULLEYRemove any oiland clean,
LOWEnCOVER
lnstall with concavesurface facing out,Remove any oilano ctean.
NOTE: When installing a new crankshaft and/or new bolt:
O tighten the crankshaft pulley bolt to 196 N'm (20.0 kgf'm, 145 lbf'ft),
O loosen bolt,
O retighten it to 177 N.m (18.0 kgt.m, 130 lbf'ftl.
'14 x 1,25 mmlt7 t{.m 118.0 kgl.m, 130lbtftlReplacsmenl, page 6-8
6-7

Cylinder Head
Removal (cont'dlI
12.R€move the spark plug caps and distributor from
the cvlinder head.
Remove the upper radiator hose, heater hose and
water bypass hose.
UPPER RAI'IAYOR
14. Remove th6 solash shield.
WATER BYPASS
9.8 N.m {1.0 kgt m.t.2 tbr.frt
sHtEut
15. Remove the engine ground cable.
Remove the adjusting bolt and mounting bolts, then
remove the power steering (P/S) pump belt 8nd P/S
pump.
. Do not disconnect the P/S hoses.
6x1.0mmADJUSTINGBOLT9.8 N.m 11.0 tgfm,7.2 tbf.ftl
8 x 1.25 mm24 .m (2.akstm, 17lbf.ftl
P/S PUMP
Remov€ the air conditioning (Ay'Cl compressor(see pags 6-10).
R€move the alternator belt (see page 6-10).
Ramove the cruise control actuator.
8 x 1.25 mm2a N.m 12.4 kgt m,
belt
17.
t8
ACTUATOR

Removal
NOTE:
. Turn the crankshaft pulley so the No. 1 piston is at
top dead center {TDC) before removing the belt (see
page 6-51).
. Inspect the water pump when removed the timing
belt {see page 10-9).
Remove the wheel well splash shield (see page 6-
57 ).
Loosen the adiusting bolt and mounting bolts, then
remove the power steering (P/S) pump belt.
I x 1.25 mm2a N.m l2.a kgt.m, 17 lbt ttl
Loosen the adjusting bolt and idler pulley bracket
bolt, then remove the air conditioning (Ay'C) com-
oresso. belt.
D1INBOLT10 x 1.25 mmira N.m (4.5 kgf.m, 33 lbf'ttl
AOJUSTING
ADJUSNNG
BELT
4. Loosen the adiusting nut and mounting nut, then
remove the alternator belt.
NUTI x 1.25 mm24 N.m {2.a lgf.rn,17 tbf.ftl
MOUNTING NUT10 x 1.25 mm4,t N.m lia.5 kgl.m,33 tbt ftl
Remove the cruise control actuator (see page G58).
Bemove the side engine mount.
10 x 1.25 mm52 N.m 15.3 kgt m, 38 lbtftl
CNGINCMOUNT
12 x 1.25 mm74 N.m (7.5 kgt m,s4 lbf.trl
(cont'd)
6-49

Timing Belt
Installation (cont'dl
1Loosen and retighten the adjusting bolt to tsnsion
thB belt.
Rotate the crankshaft about 4 or 6 turns countsr-
clockwise so that the belt positions on the pulleys.
Adjust ths timing bolt tension (see pags &48).
Ch€ck ths crankshaft pullsy and the camshaft pul-
lsys at TDC.
CRANKSHAFT PULLEY:
1.lf a camshaft pulley is not positioned at TDC.
.emove the timing belt and adiust the positioning
following the procedure on page 6-51, th6n r6install
rhe riming belt.
NOTE: Refsr to page 6,19 for timing b€lt removal.
Aft€r installation, adiust the tension of each b€lt.
o See section 23 for alternator belt tension adiust-
menr.
. See section 22 tot NC compr€ssor b6lt tension
adjustm€nt.
. See section 17 for P/S pump b6lt t€nsion adiust-
menL
4.
5.
b.
CAMSHAFT PULI..EY:
"UP- MANKS
6-52

Cylinder Head
Removal (cont'dl
Remove the heat shield from the P/S bracket (see
page 5-18).
Remove the air conditioning (Ay'Cl compressor belt(see page 6-49).
Remove the alternator belt {s€e page 6-49).
Remove the cruise control actuato..
16.
17.
'18.
'19.
ACTUATOR
20. Remove the side engine mount.
10 x 1.25 mm
SIDE ENGINE
12 x 1.25 mrn7a N.m 17.5 kgl.m,5a rbtftl
8 x 1.25 mmN.m 12.4 kgf.m, 17 lbtftl
21. Remove the cylinder head cover.
22. Remove the timing belt (see page 6-49).
23. Remove the camshaft pulleys and back cover.
24. Remove the exhaust manifold.
SELF.LOCKING NUT8 x 1 .25 mm31 N.m {3.2 kgt m, 23 lbf.ftlReplace.
6-58
'ilffi{

Oil Pump
5.
4.
Removal/lnspection/lnstallation
6. Remov€ the timing belt.
7. R€move the drive pulley.
8. Remov€ the oil pan and oil screen.
9. Remove the oil pump.
Drain the engine oil.
Turn the crankshatt and align the white groove on
the crankshalt pulley with the pointer on the lower
cover.
Remove the cylinder head cover and middle cover.
Remove the power steering pump belt, air condition-
er belt and the alternator belt.
Remove the crankshaft pulley and remove the low-
er cover.
OIL PUMP
OIL PAN
8-10
1O. Remove the screws trom the pump housing, thsn
separate the housing and coveJ.
1 1. Check the inner-to outer roto. radial clearance on thepumP rotor.
Innor Rotol-to-Outor Rotor Radial Cloaranco
StandErd (Newl: O.O4-O.16 mm(0.O02-0.006 in)
Service Limit: O.2O mm (0.008 inl
Check the housing-to-rotor axial clearance
pump rotor.
Housing-to-Botor Axial Claalanc€
Standard (Nowl: O.O2-O.O7 mm(O.OO1 -O.OO3 inl
Service Limit: O.15 mm (0.006 in)
on the12.
HOUSING