1992 MAZDA PROTEGE battery

REAR SIDE WINDOW REGULATOR AND GLASS
REAR SIDE WINDOW REGULATOR AND GLASS
COMPONENTS
Removal / Installation
1. Open the rear door glass fully.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to Removal Note.
4. Install in the reverse order of removal, referring to Installation Note.
Caution
l Remove the door screen carefullv so that it may be reused.
3-9 61-67 in-lb) ,
03uosx-019
1. Regulator handle (Manual window) 9. Center channel, channel protector
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-l 2 10. Rear door glass
2. Rear door trim (Manual window) Removal Note ..,.....,..,................. page S-l 8
3. Rear door trim (Power window) Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-18
4. Inner handle Il. Quarter window glass, weatherstrip
5. Pull handle bracket (Power window) 12. Manual window regulator
6. Rear power window switch 13. Power window regulator
7. Sealing pad 14. Glass run channel
8. Door screen
s-17

REAR DOOR LOCK AND OPENER S
REAR DOOR LOCK AND OPENER
COMPONENTS
Removal / Installation
1. Raise the rear door glass fully to remove the door lock assembly.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to Removal Note.
4. install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
4.2-6.2 N-m
1, Regulator handle (Manual regulator) 7. Sealing pad
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-l 2 8. Door screen
2. Rear door trim (Power window) 9. Lock knob assembly
3. Rear door trim (Manual window) 10. Lock control (Power door lock)
4. inner handle 11, Rear door lock assembly
5. Pull handle bracket (power window) 12. Outer handle
6. Rear power window switch
s-19

S REAR HATCH
REAR HATCH
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
Note
l Remove the trunk end trim, trunk side cover, trunk side trim, rear header trim, rear seat belt
upper anchor, and C-pillar trim for removal of rear harness No.2. (Refer to pages S-98, 101.)
l Remove the rear portion of the headliner for removal of the rear hatch hinge and washer pipe.
(Refer to page S-91.)
I
I
\/ 8.8-13 N.m f60-130 cm-ka. 78-l 13 In-lb)
18-23 (1.8-2.3, 12-17)
7.8-12 N-m (80-120 cm-kg, 89-104 In-lb)
=?.3, 12-17)
7.8-12 Nin
(80-120 cm-kg,
89-l 04 in-lb)
Rear hatch
Rear hatch striker
1. Rear harness No.2
6. Trunk end trim
2. Washer pipe
Removal I Installation . . . . . . . . . . . . . . . . . . page S-98
3. Stay damper 7. Rear hatch striker
4. Rear hatch Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-21
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-21 8. Rear hatch opener cable
5. Rear hatch hinge
s-20

S REARHATCH LOCKANDOPENER
REARHATCH LOCKANDOPENER
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
2 lnctall in the rpvprs~! order of rwnoval.
2.3, 12-17)
N.m (m-kg, ft-lb
_____-
0.1UOSX-C’
Rear hatch lock Rear hatch opener, opener cable
1. Rear hatch lower trim 5. Trunk end trim
Removal / Installation .,......,,...... page S- 98 Removal / Installation .,,......,,._... page S- 98
2. Lock cylinder retainer 6. Rear hatch striker
3. Lock cylinder assembly Adjustment Note ,.,,,,,,,......,,,,,... page S- 21
4. Rear hatch lock assembly 7. Scuff plate, Trunk side cover, Trunk side trim,
Quarter trim (R.H. side)
Removal / Installation ,.........,..... page S- 98
8. Opener lever
9. Rear seat cushion
Removal / Installation . . . . . . . . . . . . . . . . page S-l 12
10. Rear hatch opener cable
s-22

POWER DOOR LOCK SYSTEM s
Power door lock system does not operate
(All doors)
I
Check ROOM 10A and DOOR OK NG VB: Battery voltage - Repair harness and replace fuses
1
Check for battery voltage at terminal-wire (L/R) of door
lock switch connector NG
Repair harness (Fuse box-Door lock switch)
1 OK
Check terminal voltage above connector with switch
each condition
Locked
Unlocked (G/R) wire
Va
ov (G/O) wire
ov
VB
1 OK
Check door lock switch (Refer to page S-26)
Disconnect door lock timer and relay connector:
check for battery voltage at terminal-wire (W/G) NO
- Repair harness (Fuse box-Door lock timer and relay) OK
Check terminal voltage above connector with switch
each condition
Lot ked
Unlocked
VB
ov (G/O) wire
ov
VB
1 OK
NO
Repair harness =
(Door lock switch-Door lock timer and relay)
1
Check for continuity of above connector terminal-wire
(B) to ground Repair harness (Door lock timer and relay-Ground)
I OK
Connect battery voltage to terminal-wire (G) and ground
terminal-wire (R) of door lock timer and relay; check that NGT Broken harness (Door lock timer and relay-Door lock
doors lock control) or defective door lock control
Reverse above connection; check that doors unlock (Refer to inspection; page S-26)
I OK F Check door lock timer and relay (Refer to page S-26)
23uosx-007 One door lock does not operate
t
Check door lock control (Refe Replace door lock control (Refer to pages S-13, 14, 19)
I OK __ Repair harness
- (Door lock timer and relay-Door lock control)
03uosx-030
s-25

POWER DOOR LOCK SYSTEM
03uosx-03:
DOOR LOCK SWITCH
Inspection
1 1 Disconnect the door lock switch connector.
2. Check for continuity between terminals of the switch with
an ohmmeter. -,
Locked 0 0
Unlocked 0 0
O--O: Indicates continuity
3. If not as specified, replace the door lock switch.
DOORLOCKCONTROL
Inspection
1. Disconnect the door lock control connector.
2. Check operation of the door lock control when battery volt-
age is applied to the terminals.
VB: Battery voltage
Connection
43 Ground Door lock control condition
b a Locked
a b Unlocked
3. If not as specified, replace the door lock control.
DOOR LOCK TIMER AND RELAY
Inspection
1. Check for continuity between terminals of the door lock timer
and relay with an ohmmeter.
Terminals 1 Continuity 1 Terminals 1 Continuity 1 Terminals 1 Continuity
a-b
I X 1 b-d 1 X 1 c-h 1 X
I a-c I 0 I b-e I X I d-e I 0 I
I
a-d I 0 1 b-f 1 X I d-f I 0 I
a-e 0 1 b-h ) 0 ) d-h ) X a-f I 0 1 c-d 1 0 I e-f I 0 I
a-h X c-e 0 1 e-h 1 X
b-c 1 X c-f
0 ( f-h ) X
I
O...Yes X...No
Note
l Set the tester to the x 1,OOOQ range.
2. Connect battery voltage to terminal (b) and ground termi-
nal (a). Then, short circuit between terminals (h) and (d) or
(h) and (c), and check that the relay clicks.
S-26

POWER WINDOW SYSTEM S
Power window system does not operate
(All doors)
I
NG
Check POWER WIND 30A fuse - Repair harness and replace fuse
I
1 OK
Turn ignition switch ON
Check for battery voltage at terminal-wire (B/W) of main NG
power window switch connector Repair harness (Fuse box-Main power window switch)
I
OK
Disconnect main power window switch connector;
check continuity of terminal-wire (B) to ground Repair harness (Main switch-Ground)
OK
- Check main power window switch (Refer to page S-31)
I I
23UOSX-010
Only driver side power window does not operate
( Turn ignition switch ON
Check for battery voltage at terminal-wires (R/B) and
(R/G) of main power window switch connector
UP
DOWN (R/G) wire
~ _ 1 NG -i VB: Battst’y VOltaQe,
Check main power wrndow switch (Refer to page S-31)
OK
Check for battery voltage at terminal-wires (R/B) and
(R/G) of power window motor connector OK
= Check power window motor (Refer to page S-32)
23UOSX-011
Sk29

POWER WINDOW SYSTEM
II
Power window (except driver side) cannot be
operated by main switch
t
Turn ignition switch ON Note l Use only main switch during checking operation.
t
Check for battery voltage at terminal-wires of main
power window switch connector
Switch Condition
Passenger UP
side
DOWN
Rear (LH) . UP
DOWN
Rear (RH) UP
DOWN Terminal Voltage
(G/W) wire Ve
(R/W) wire VB
(G/Y) wire VB
(W/R) wire VB
(L/W) wire VB
(Y/W) wire Ve
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
VB: Battery voltage
NO
- Check main power window switch (Refer to page S-31) NG
___) Repair harness
(Main power window switch-Power window sub-switch)
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
Condition Terminal
UP (R) wire VB
DOWN (G) wire VB
I Check power window sub-switch (Refer to page S-32)
1 OK
Check for battery voltage at terminal wires of power
window motor connector while operating main switch
Condition Terminal Voltage
UP (R) wire
DOWN (G) wire OK
Check power window motor (Refer to page S-32) I 23uosx-012
s-30