1992 MAZDA PROTEGE battery

F CONTROL SYSTEM
VB: Battery voltage
erminal Input Output Connection to
Test condition Correct voltage Remark
28 1 0 )
1 Airflow meter Ignition switch ON Approx. 3.8V
-
2c 0 Oxygen sensor
2D 0 Fan switch Idle Approx. 3.3V
Ignition switch ON ov
Idle (Cold engine)
ov
Idle (After warm-up) O-l .ov -
increasing engine speed (After warm-up) 0.5-I .ov
Deceleration o-0.4v
Fan operating (Engine coolant tempera- ov
ture over 97OC (207°F) or diagnosis con-
nector terminal TFA grounded) -
2E 0 Water thermo-
sensor Fan not operating (Idle) VS
Engine coolant temperature 20% (68OF)
After warm-up Approx. 2.5V f&ition switch
Below 05V
2F , 0 , , Throttle sensor , Accelerator pedal released
Accelerator pedal fully depressed
2G 0
2H 0 ATF thermosensor -30°C (-20°F) -150°C (302OF) Approx. 4.9%1.12V Ignition switch
ATF
Temp 20% (68OF) Approx. 4.6V ON
130% (266OF) Approx. 1.54V
Hold switch Switch debressed ov Ignition switch
i I I
Switch released Va ON
21 0 Throttle sensor Constant 4.5-5.5v Ignition switch
ON
I , I 2J 0 Distributor Ignition switch ON Approx. OV
(G-signal) [DOHC] or 5V _-
Idle Approx. 1.5V
2K 0 Intake air ther- Ambient air temperature 20% (68’F) Approx. 2.5V Built in airflow
mosensor meter
2L - - - -
- -
2M 0 Pulse generator Engine running at idle (N range) Above 0.6V
-
(IN)
Engine stopped (Ignition switch ON) ov
2N Pulse generator Constant ov
ground
20 0 Solenoid valve ignition switch ON Va
(Purge control) -
Idle Va
2P 0 Hold indicator Hold mode Below 2V Ignition switch
ON
Normal mode VB
23UOFX-1
1 Ul Iv
I u1
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 20)21Vi,2~]2112Gj2E)2Cj2~ iuI1s]l~lollMIlKI1IJ1~~t~l1Cj1~
32 j3X I3V 13T13R13P13N)3L13J(3H13F( 3D 13s 2P(2N\2L12J12H12F(2D126 1V IATIlRhPjlN(1 LjlJ Ilt-illFI 1 DI 16
4-
F-l 62

CONTROL SYSTEM F
Incorrect voltage Possible cause ____-__l_ll____-
Always approx. OV or approx. 5V l Refer to Code No.08 Troubleshooting (Refer to page F-90)
IV after warm-up
Jlways approx. IV after warm-up
l Refer to Code No.15 Troubleshooting (Refer to page F-98)
l Refer to Code No.1 7 Troubleshooting (Refer to page F-100)
qlways OV
Electrical cooling fan OK)
l Open or short circuit in wiring from fan relay to ECU terminal 20 l ECU malfunction
I Always approx. OV or approx. 5V l Refer to Code No.09 Troubleshooting (Refer to page F-92)
Always constant
C\lways above 1V
4lways constant . Open circuit in wiring from ECU terminal 2F to throttle sensor
l Open circuit in wiring from ECU terminal 21 to throttle sensor l Open circuit in wiring from ECU terminal 3D to throttle sensor
l Throttle sensor misadjustment
l ATF termosensor malfunction (Refer to page K-142) l Open or short circuit in wiring from ATF termosensor to ECU terminal 2G
c\lways OV
l Hold switch malfunction (Refer to page K-140) l Short circuit in wiring from hold switch to ECU terminal 2H
4lways Va
l Hold switch malfunction (Refer to page K-140) l Open circuit in wiring from hold switch to ECU terminal 2H
Always OV
l Short circuit in wiring from ECU terminal 21 to throttle sensor airflow meter,
or water thermosensor
l Poor connection at ECU connector
Below 4.W or above 5.W
Always approx. OV or approx. I..% l ECU malfunction
l ECU malfunction
l Refer to Code No.03 Troubleshooting (Refer to page F-88)
Always approx. OV or approx. 5V 9 Refer to Code No.10 Troubleshooting (Refer to page F-94)
I
- - VB:
Battery voltage
Always constant
l Pulse genrotor malfunction (Refer to page K-142) l Open or short circuit in wiring from pulse generator to ECU terminal 2M
Above OV
l Poor connection at ground terminal l Open circuit in wiring from ECU terminal 2N to ground
F-l 63

F CONTROL SYSTEM
srmina
3A
38
3c
3D
3E
3F
3G
3H
31
3J
3K
3L
3M
3N
30
3P
3Q
3R
3s
3T I input Output Connection to
Test condition Correct voltage Remark Battery voltage t
- -
Ground (Injector) Constant OU -
- -
Ground (Output) Constant OU -
- -
Ground (CPU) Constant OU -
- -
- Ground (Input) Constant ov
0 Inhibitor switch
D range VB Ignition switch
(D range) ON
Other ranges ov
0 DRL relay Parking brake pulled with ignition switch
l DRL: Daytime
(Canada) ON (DRL OFF) Va
Running Lights
Idle (DRL ON) Below 2.5V 0
Inhibitor switch
(L range) L range
Other ranges VB
ov Ignition switch
ON
0 Inhibitor switch
(S range) S range
Other ranges Va
ov Ignition switch
ON
_-__. - -. -
0 Solenoid valve Engine speed below 5,000 rpm Below 1.5V WCS: Variable In-
(VICS)
Engine speed above 5,000 rpm VB ertia Charging
System [DOHC]
- - -
- - -
- -
- - -
- - -
- - -
0 Solenoid valve 60 [DOHC]/120 [SOHC] seconds after Below 1.5v
(Pressure regula- engine started when engine coolant tem-
tor) [BP] perature above 90% (194*F) and intake
-
air temperature above 58% (136OF)
[DOHC]/50”C (122“F) [SOHC]
Other condition at idle Va
- - - - - -
- -
-
A- - -
- -
- I -
0 ISC valve Ignition switch ON VS
l Engine signal
Monitor: Green
I I Idle I
Approx. 1 OV and red lamps
flash
I
-
- - - -
-
- - - -
- - - - - -
23UOFX-1’
‘) )
U- r, )
IJ- l-1
I 1 r
3Y I3W I3U [3S13d3&M13K 31 13Gj3EI 3C
I3A 20/2M;2K( 21 12G(2E12C12A 1 U 11 Sll o]lOll MI1 K 1 I (1 G(1 E[ 1
C 11 A
32 13x [ 3V(3~(343~I3N[3~ 3~(3~(3~13~ 136 2P12N(2L[2J12H(2F(2D126 iv I~TI~RI~P(~NIIL i~(lii(l~I lo(le
.
F-l 64

CONTROL SYSTEM F
Incorrect voltage
Above OV
Always OV
Always VB
Always Va
Always OV
Always Ve
Always OV
Always VB
Always approx. OV or VB -
-
-
Always OV or Ve -
-
-
Always OV or Vs -
-
- Possible cause
VB: Battery voltage
l Poor connect at ground terminal l Open circuit in wiring from ECU to ground
l Inhibitor switch malfunction (Refer to page K-141) l Short circuit in wirina from inhibitor switch to ECU terminal 3E
l Inhibitor switch malfunction (Refer to page K-141)
. Open circuit in wiring from inhibitor switch to ECU terminal 3E
l Short circuit in wiring from DRL relay to ECU terminal IL l Short circuit in wiring from DRL relay to DRL unit
l Open circuit in wiring from DRL relay to ignition switch
l Parking brake switch always ON l DRL unit malfunction (Refer to page T-33)
l Inhibitor switch malfunction (Refer to page K-141) l Short circuit in wiring from inhibitor switch to ECU terminal 3G
l Inhibitor switch malfunction (Refer to page K-141) l Short circuit in wiring from inhibitor switch to ECU terminal 3G
l Inhibitor switch malfunction (Refer to page K-141) l Short circuit in wiring from inhibitor switch to ECU terminal 3H
l Inhibitor switch malfunction (Refer to page K-141) l Open circuit in wiring from inhibitor switch to ECU terminal 2H
l Refer to Code No.41 Troubleshooting (Refer to page F-103) -
-
-
l Refer to Code No.25 Troubleshooting (Refer to page F-102) -
-
-
l Refer to Code No.34 Troubleshooting (Refer to page F-103) -
-
F-l 65

F CONTROL SYSTEM
Ve: Battery voltage
erminal Input Output
Connection to Test condition Correct voltage Remark
3u 0 Injector (Nos. 1, 3) Ignition switch ON VB * Engine Signal
Idle Va Monitor: Green
and red lamps
Engine speed above 2,000 rpm on de- Va
flash
celeration (After warm-up)
3v 0 Injector (Nos. 2, 4) ignition switch at idle
VB
Idle VB
Engine speed above 2,000 rpm on de-
VB
celeration (After warm-up)
3W 0 1-2 shift solenoid Solenoid valve ON i&I AT running
valve
Solenoid valve OFF ov
3x 0 2-3 shift solenoid Solenoid valve ON
VB AT running
valve
Solenoid valve OFF ov
3Y 0
ZH;hift solenoid Solenoid valve ON VB AT running
Solenoid valve OFF ov
32 0 Lockup solenoid Solenoid valve ON
VB AT running
valve
Solenoid valve OFF ov
23UOFX-1~
1 I u- l-1 ,
III h-3
I r
3y 13W 13U (3Sl3Cj3+4]3K 31 13Gj3EI 3C 13A 2012h42Kl21 12Gl2E12Cj2A 1 U 11 SllC$O 1 MI1 K 1 I 11 G 1 El 1 C 11 A
32 )3X I3Vj3Tj3R]3Pj3N]3L 3Jj3Hj3F13D 138 2P)2N)2L~2J~2H~2F~2D~2B 1V IlTjlRjlP 1NjlL 1JjlH 1FI lD\lB
-*’
.J’ -
F-l 66

F CONTROL SYSTEM
23UOFX-15
23UOFX-15
23UOFX-15
LOCK
4
I
13UOFX-oc
F-l 72
6. Turn the ignition switch OFF.
7. Disconnect the negative battery terminal for
at least 20 sec.
to eliminate the malfunction code that was created during
inspection from the control unit memory.
Replacetnent
1. Disconnect the oxygen sensor connector.
2. Remove the oxygen sensor.
3. Install in the reverse order of removal.
Tightening torque:
29-49 N-m (3-5 m-kg, 22-36 ft-lb)
MAIN RELAY (FUEL INJ RELAY)
Inspection
1. Verify that the main relay clicks when turning the ignition
switch ON and OFF.
2. Apply battery voltage to terminal A and ground terminal E3
of the main relay.
3. Check continuity of the terminals as shown.
VB: Battery voltage
Terminals 1 Ve not applied VB applied
C-D No continuity Continuity
4. If not as specified, replace the main relay.
CLUTCH SWITCH (MTX)
Inspection
1, Disconnect the clutch switch connector.
2. Connect an ohmmeter to the switch.
3. Check continuity of the switch.
Pedal Continuity
Depressed Yes
Released No
4. If not as specified, replace the clutch switch. ,
Replacement
1. Disconnect the clutch switch connector.
2. Loosen the locknuts.
3. Remove the clutch switch.
4. Install in the reverse order of removal.
5. Adjust the pedal height. (Refer to page H-6.)

G
ENGINE ELECTRICAL SYSTEM
INDEX ......................................................
OUTLINE ..................................................
SPECIFICATIONS .................................... G- 3
TROUBLESHOOTING
GUIDE.. .................... G-
4
DIAGNOSTIC INDEX ................................
SYMPTOM TROUBLESHOOTING..
............. :- t
-
CHARGING SYSTEM ................................. G- 6
PREPARATION .......................................
CIRCUIT DIAGRAM ................................. :I ;
TROUBLESHOOTING .............................. G- 7
BATTERY ............................................... G- 6
ALTERNATOR ........................................ G-10
DRIVE BELT ........................................... G-14
IGNITION SYSTEM .................................... G-15
PREPARATION ....................................... G-15
CIRCUIT DIAGRAM ................................. G-15
TROUBLESHOOTING .............................. G-16
IGNITION TIMING ................................... G-17
HIGH-TENSION LEAD .............................. G-17
SPARK PLUGS ....................................... G-16
IGNITION COIL ....................................... G-19
DISTRIBUTOR ........................................ G-20
IGNITER ................................................ G-23
STARTING SYSTEM .................................. G-24
PREPARATION ....................................... G-24
CIRCUIT DIAGRAM ................................. G-24
STARTER ...............................................
G-25
STARTER INTERLOCK SWITCH (MTX)
........ G-31
03UOGX-001

G INDEX
NDEX
- 03UOGX-00:
6. Ignition coil 1. Battery
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page G- 8
Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..t page G- 9
2. Alternator
Removal / Installation . . . . . . . . . . . . . . . . . .
page G-l 0
Disassembly / Assembly . . . . . . . . . . . . . page G-l 1
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 2
3. Drive belt
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 4
Adjustment . . . . . . . . page G-l 4
Replacement . . . . . . . . . . . . . .
page G-l 4
4. High-tension lead
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page G-l 7
5. Spark plugs
Removal / Installation . . . . . . . . . . page G-1 0
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 8
G-2
Inspection .,.. . . . . . . . . . . . . . . . . I . . . . . page
G-l 9
7. Distributor
Spark test ., . . . . . . . . . . ,... . . . . . . . .
page G,-20
Electronic advance inspection page G-20
Removal / Installation ,................. page G-21
Disassembly / Assembly.. , . . page
G-22
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-22
8. Igniter
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-23
9. Starter
Removal / Installation .;...........,.... page G-25
Disassembly ! Assembly . . . . . . . . . . . . . page G-26
Inspection . . . . ...‘........................,,,
page G-28 .--
10. Starter interluck switch
Inspection... . . . . . . . . . . . . . . . . . . . . ,.., ,...,
page G-31