1992 MAZDA PROTEGE battery

OUTSIDE MIRROR
c a
23UOSX.042
POWER OUTSIDE MIRROR
Inspection
1. Remove the power outside mirror. (Refer to page S-56.)
2. Check for continuity between terminals with an ohmmeter.
I
Terminal I
t
a C d
0 I
A I
0
o--O : indicates continuity
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable. (With power outside mirror.)
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
MANUAL CONTROL
S-56

S WINDSHIELD
WINDSHIELD
PREPARATION
SST
49 0305 870A I 1 For
Tool set, window removal and
installation of
windshield
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
PROTEGC

REAR WINDOW GLASS S
REAR WINDOW GLASS
PREPARATION
SST
49 0305 870A
1 For
Tool set, window removal and
installation of rear
window glass
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note.
r
I’
PROTEGi:
1. Rear seat cushion
6. Rear header trim
5
Removal I Installation . . . . . . . . . . . . . . . . page S-l 11
Removal / Installation . . . . . . . . . . . . . . . . page S-
97
2. Rear seat back/side
7. C-pillar trim
Removal I Installation . . . . . . . . . . . . . . . . page S-l 11
3. High-mount stoplight (interior mounted)
Removal / Installation . . . . . . . . . . . . . . . . . . . . . Section
T
4. Rear package trim
Removal I Installation . . . . . . . . . . . . . . . . page S-
97
5. Rear seat belt upper anchor
Removal / Installation ..,............. page
S-101
Removal / Installation . . . . . . . . . . . . . . . . page S-
97
8. Rear window molding
Removal I Installation . . . . . . . . . . . . . . . . page S-
43
9. Rear window glass
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 64
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page S-
65
10. Spacer
S-63

WINDSHIELD WIPER AND WASHER
Wiper does not operate in Lo or Hi position
(With wiper relay)’
I
Check WIPER 20A fuse
Repair harness and replace fuse
VB: Battery voltage
OK
Turn ignition switch ON
Check for battery voltage at terminal-wires (L) of wiper
relay connector NG
- Repair harness (Fuse box-Wiper relay)
I OK
Check for battery voltage at terminal-wires (W) and
(G/W) of above connector
I Replace wiper relay (Refer to Section T)
OK
Disconnect wiper switch connector;
check for battery voltage at terminal-wires (W) and
W’J) Repair harness (Wiper relay -Wiper switch)
I OK
Check for continuity of above connector terminal-wire
(B) to ground
I
Repair harness (Wiper switch-Ground) 1
1 OK
Check wiper switch (Refer to
I Replace combination switch (Refer to Section T)
1 OK
Check for battery voltage at terminal-wires (L/W) and (R)
of wiper relay connector with switch as shown NG
Replace wiper relay (Refer to Section T)
l Lo : (L/W) Ve l Hi : (R) Ve
OK
1 I
Disconnect wiper motor connector; check for battery
voltage at terminal-wires (L/W) and (R) with switch as
shown
l !-0 : (L/w) VB l Hi : (R) VB NG
= Repair harness (Wiper relay-Wiper motor)
OK
Check continuity between wiper motor body and
ground NG
= Repair ground circuit of wiper motor body
Check wiper motor (Refer to page S-70)
*: U.S. with/without cruise control, Canada with cruise control
23UOSX-017
Wiper does not operate in Lo or Hi position
(Without wiper relay)’
Check WIPER 20A fuse
OK
Repair harness and replace fuse .-
S-68 Cont’d

WINDSHIELD WIPER AND WASHER S
Cont’d
Turn ignition switch ON t
VB: Battery voltage
Check for battery voltage at terminal-wire (L) of wiper
switch connector
I Repair harness (Fuse box-Wiper switch)
1 OK
Check for battery voltage at terminal-wires (L/W) and
(L/R) of wiper switch connector with switch as shown
l Lo : (L/W) va l Hi : (R) VB
I OK NG
= Check wiper switch (Refer to page S-71)
Disconnect wiper motor connector; check for battery
voltage at terminal-wires (L/W) and (R)
l Lo : (L/W) VB l Hi : (R) Ve NG
- Repair harness (Wiper switch-Wiper motor) L
J
OK
I
Check continuity between wiper motor body and
ground Repair ground circuit of wiper motor body
*: Canada without cruise control Check wiper motor (Refer to page S-70)
23UOSX-018
II Wiper automatic park function does not work
II
I t-
I 1 Turn ignition switch ON I
I
+
Check for battery voltage at terminal-wire (L) of wiper
motor connector
OK Repair harness (Fuse box-wiper motor)
Disconnect wiper motor and wiper switch connectors;
check for continuity between terminal-wire (L/Y) of
above connectors
OK Repair harness (Wiper motor-Wiper switch)
Reconnect wiper switch connector;
check for continuity between terminal-wires (L/Y) and
(L/W) of wiper motor connector Check wiper switch (Refer to page S-71)
Check wiper motor (Refer to page S-70)
I
23UOSX-019
One touch function (MIST) does not operate
Jl
Check wiper switch (Refer to page S-71)
I
03UOSX-118
S-69

WINDSHIELD WIPER AND WASHER
Intermittent function does not operate
(With wiper relay)*
i
Disconnect wiper relay connector;
check for continuity of terminal-wire (B) to ground
I Repair harness (Wiper relay-Ground)
OK
=j Replace wiper relay (Refer to Section T)
*: U.S. with/without cruise control, Canada with cruise control
03uosx-119
Intermittent function does not operate
(Without wiper relay)*
1
Disconnect wiper switch connector;
check for continuity of terminal-wire (B) to ground Repair harness (Wiper switch-Ground)
*: Canada without cruise control
Washer does not operate (Wiper operates OK)
1
I
wiper 1 -
repay Check for battery voltage at terminal-wire
Repair harness (Fuse box-Wiper switch) l
1 (L) of wiper switch connector J
1 OK
Check for battery voltage at terminal-wire (L/O) of
washer switch connector with washer switch ON Check washer switch (Refer to page S-71)
1
1 OK
Disconnect washer motor connector;
check for battery voltage at terminal-wire (L/O) with
washer switch ON Repair harness (Washer switch-Washer motor)
Check for continuity of above connector terminal-wire
(B) to ground Repair harness (Washer motor-Ground)
*l: Canada without cruise control
*2: U.S. with/without cruise control, Canada with cruise control
23UOSX-020
WIPER MOTOR
Inspection
Conductivity check
1. Disconnect the wiper motor connector.
2. Check for continuity between terminals with an ohmmeter.
--iizzs
In automatic park
Out automatic park
o---O: Indicates continuity

WINDSHIELD WIPER AND WASHER
. .
”
I I I
1 23UOSX-021

b
a
I-----
WASHER
TANK
‘WASHER MOTOP
23UOSX-02:
TYPE 1
TYPE 2 I
db
h d
13uosx-0’
Operation check
1. Disconnect the wiper motor connector.
2. Check operation by applying battery voltage to the termi-
nal of the motor.
Terminai
1 Operation speed
I
WASHER MOTOR
Inspection
Conductivity check
1. Disconnect the washer motor connector.
2. Check for continuity between terminals (a) and (b) with an
ohmmeter.
Operation check
1. Disconnect the washer motor connector.
2. Connect battery voltage to terminal (b) and ground termi-
nal (a).
3. Verify that the motor operates.
WINDSHIELD WIPER AND WASHER SWITCH
Inspection
1. Disconnect the windshield wiper and washer switch con-
nector. (Refer to Removal of combination switch; Section T.)
2. Check for continuity between terminals with an ohmmeter.
m: Indicates continuity
S-71

S WINDSHIELD WIPER AND WASHER
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
Note
l Refer to Section T for removal of the windshield wlper and washer switch (In combination switch)
and wioer relav.
8.8-14 N-m
(100-140 cm-kg,
87-122 in-lb)
Wiper Washer
1. Wiper arm cover 7. Washer tank assembly
2. Wiper arm and blade a. Washer tank
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-73 b. Washer motor
3. Cowl grille Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . ..**.....
page S-71
Removal / Installation . . . . . . . . . . . . . . . . . . page S-53 c. Grommet
4. Baffle 8. Washer pipe
5. Wiper motor and bracket 9. Washer nozzle
Removal Note I Installation Note page S-73 Adjustment Note .,...................,... page S-73
&~-’
Inspection . . . . _. . . . . . . . . . . . . . . page S-70
6. Wiper link
s-72