1991 MITSUBISHI ECLIPSE ABS

5-62BRAKES - Brake Line
BRAKE LINEREMOVAL AND INSTALLATIONr/ehicles without ABS
Pre-removal Operation
eDraining of Brake Fluid6
/
NOSKA-
>/Flared brake line nuts
13-17 Nm
9-12 ft.lbs.I
14FO3825-35 Nm
/ 18-25 ftlbs.17-26 Nm
12-19 ft.lb!
5.25-35 Nm
18-25 ftlbs.12-19
ft.lbs.
1. Front brake hose2. Strut brake tube
3. Front brake tube
(R.H.)4. Front brake tube (L.H.)5. Brake tube (A)6. Brake tube (9)11. Main brake tube (R.H.)12. Main brake tube (L.H.)13. Proportioning valve
14. Rear brake hose
15. Rear axle brake tube
16.BracketMAO583

--
BRAKES - Brake Line5-63
Vehicles with ABSPre-removal Operation
*Draining of Brake FluidZonnecting part of14A057i
!
4*1. Front brake hose2. Strut brake tube
3. Front brake tube
(R.H.)4. Front brake tube (L.H.)5. Brake tube (A)6. Brake tube (9)7. Rear brake tube (R.H.)8. Rear brake tube (L.H.)~~ 9. Hydraulic unit10. Main brake tube (R.H.)11. Main brake tube (L.H.)2:12.Proportioningvalve
13. Rear brake hose
14. Rear axle brake tube
15.Bracket17-26 Nm
12-19
ftlbs.17-26 Nm
12-19 ft.lbs.14A0585

5-70
REAR DISC BRAKE
BRAKES -’ Rear Disc Brake
REMOVAL AND INSTALLATION
IPre-removal Operation
@Draining of Brake Fluid

~1 ,.
l Adjustment of Parking Brake Lever
1.150-60Nm
9-14
Nm36-43ft.lbs.
7-10ft.lbs./
7- 10ft.lbs.
Removal steps
4*1. Parking brake cable connection
2. Brake hose connection
3. Rear brake assembly
4. Rear brake disc
5.
Hubcab
+4 76. ME;AFearing nut
8: Rear speed sensor bracket
9. Rear hub assembly
14. Dust shield
NOTE(1) Reverse the removal procedures to reinstall.
(2) +* : Refer to “Service Points of Removal”.(3) ** : Refer to “Service Points of Installation”.
(4) m : Non-reusable parts
MAO574

BRAKES - Rear Disc Brake59q!l
50-60Nm36-43ft.lbs.9-14Nm55-65Nm
39-47
klbs.
/160-220 Nm116-159 ft.lbs.14A0222
1. Parking brake cable connection
4*2. Brake hose connection
3. Rear brake assembly
4. Rear brake disc
+e l + IO. Self locking nutr)+ 11. Companion flange
12. Rear speed sensor
KVehicles with ABS>+e l 13. Rear axle shaftPre-removal Operation
@Draining of Brake Fluid
Post-installation Operation
l supplying Brake Fluid(Refer to
P.5-45.)l Adjustment of Parking Brake LevelStrokeP.5-42.)
NOTE
(1) Reverse the removal procedures to reinstall.(2) +e:“Service
(3) I)+ : Refer to “Service Points of Installation”.
(4) m : Non-reusable parts

BRAKES - Hydraulic Unit
HYDRAULIC UNIT
--. REMOVAL AND INSTALLATION
6Removal steps
I)+ 1. Brake tube connection
2. Relay box cover
3. Hydraulic unit harness connection
~~ l 4. Hydraulic unit5. Hydraulic unit bracket assembly
6. Bracket
7. Valve relay
1(Refer to GROUP
II-Intercooler.)Post-installation Operation
@Supplying Brake FluidaBleeding (Refer to P.5-45.)@Installation of Air Pipe B(Refer to GROUP II-Intercooler.)8. Motor relay
9. Connector bolt
10. Connector
11. Gasket
NOTE(1) Reverse the removal procedures to reinstall.
(2) +e : Refer to “Service Points of Removal”.
(3) e+ : Refer to “Service Points of Installation”.

5-78BRAKES - Hydraulic Unit
SERVICE POINTS OF REMOVAL
4. REMOVAL OF HYDRAULIC UNITb-3Remove the installation nuts, and then take out the __
hydraulic unit upward.
Caution
1. The hydraulic unit is heavy, and so care should be
taken when removing it.2. The hydraulic unit is not to be disassembled; its
nuts and bolts should absolutely not be loosened.
3. The hydraulic unit must not be dropped or other-
wise subjected to impact shocks.
4.The hydraulic unit must not be turned upside downor laid on its side.
Aotor relay
16R0670
16Rl773
INSPECTIONCheck whether there is continuity between terminals when
there is no current flow at each relay and when there is currentflow.
JlOTOR RELAY
Between
When noterminals @-@I
current flowsBetween
terminals @I-@
When current
flows between
Between
terminal
terminals @--@
@-@
30-60 52
No continuity
(WQ)
Continuity
(approx. 0 8)

BRAKES -Hydraulic Unit 5-79
Jalve relay
16R0670
87a
16Rl772
/ALVE RELAYBetween
terminals
@-@60-120 &2When noBetween
current flowsterminals
@I--@Continuity
(approx. 0 Q)Between
terminals
@J-QNo continuity(wQ2)When currentBetweenNo continuity
flows betweenterminals
@-@I(WQ)
terminal
@-@Between
terminals @--@Continuity
(approx. 0 S22)SERVICE POINTS OF INSTALLATION
4. INSTALLATION OF HYDRAULIC UNITFasten the ground wire to hydraulic unit bracket assembly.
1. CONNECTION OF BRAKE TUBEWhen connecting the tubes to the hydraulic unit, be sure
they are connected correctly.
(Refer to
P.5-64.)

5-80BRAKES - Wheel Speed Sensor
WHEEL SPEED SENSOR REMOVAL AND INSTALLATIONN06dYAG
4.
9-14 Nm
7-10 ft.lbs.
-/?’9-14 Nm
7- 10 ft.lbs./5Front speed sensor removal steps
4*I. Front toothed rotor
2. Clip
3. Connection for front speed sensor
+e l +4. Front speed sensorl +5. Front speed sensor bracket7-11 Nm
14A0584Rear speed sensor removal steps
**6. Rear toothed rotor
7. Clip
8. Cable band
9. Connection for rear speed sensor
+e I)* 10. Rear speed sensorl + 11. Rear speed sensor bracket
NOTE(1) Reverse the removal procedures to reinstall.(2) 4* : Refer to “Service Points of Removal”.(3) l * : Refer to “Service Points of Installation”.