1991 MITSUBISHI ECLIPSE oil

MANUAL TRANSAXLE - Transaxle Assembly
2i &
15-22 Nm50 11-15 ft.lbs.
Disassembly steps
l +49. Bolt50. Screw
51. Bearing retainer
+e l + 52.Intermediate gear assemblyl + 53.Input shaft assembly54. Output shaft assembly
55. Differential gear assembly
56. Bearing outer race57. Oil guide
58. Bearing outer race
59. Bearing outer race
l 4 60. Oil seal
W 61. Oil seal
62. Magnet
63. Magnet holder
64. Clutch housing assembly
NOTE(1) Reverse the disassembly procedures to reassemble.(2) ~~ : Refer to “Service Points of Disassembly”.(3) e+ : Refer to “Service Points of Reassembly”.
(4) m : Non-reusable parts
21421

MANUAL TRANSAXLE - Transaxle Assemblv 21-27
206001E
47./48. REMOVAL OF SHIFT RAILS AND FORKS’(1) Shift the Ist-2nd speed shift fork to the
2nd speed.
(2) Shift the
3rd~4th speed shift fork to the 4th speed.
(3)Rotate the the shift controls in the direction of the arrowin numerical order. Remove the shift lugs from the
control finger and interlock plate.
(4) Raise each of the shift rails upward and remove them
from the clutch housing.
(5) Remove the all shift rails and forks.
52. REMOVAL OF INTERMEDIATE GEAR ASSEMBLYLift up the input shaft assembly and remove the intermedi-
ate gear assembly.
INSPECTION
BACKUP LIGHT SWITCH
N21MOdOperate the backup light switch to check continuity with a
circuit tester. If without continuity, replace the switch.
SERVICE POINTS OF REASSEMBLYN2mnGAU
61. INSTALLATION OF OIL SEALInstall the drive shaft oil seal using the special tool.

21-28MANUAL TRANSAXLE - Transaxle Assemblv
seal
201025Apply
adhesive
(.2 in.)TFMOO63
60. INSTALLATION OF OIL SEALInstall the input shaft front oil seal using the special tool.
52. INSTALLATION OF INTERMEDIATE GEAR ASSEMBLY /
53. INPUT SHAFT ASSEMBLYLifting up the input shaft assembly, install it simultaneously
with the intermediate gear assembly.
49. APPLICATION OF ADHESIVE TO BOLTApply specified adhesive to the bolt threads.
CautionDo not apply to the bolt head.
Specified adhesive: MOPAR Part No.4318031or MOPAR Part
No.4318032
or equivalent

21-30MANUAL TRANSAXLE - Transaxle Assembly
2200048
IAmountl-2 mm(7) Measure the thickness of the crushed solder with a
micrometer and select a spacer of thickness that gives
standard
preload.,&
Standard value:
Intermediate shaft0.05-0.10 mm (.002-,004 in.)
Output shaft0.05-0.10 mm (.002-.004 in.)
Differential case0.05-0.10 mm (.002-,004 in.)
33. INSTALLATION OF OIL SEALInstall the drive shaft oil seal using the special tool.
27. INSTALLATION OF OIL GUIDEInstall the oil guide to the transaxle case as illustrated.
26. INSTALLATION OF TRANSAXLE CASE(1) Place the selected spacers on the intermediate gear
and the differential’s bearing outer race. Also insert the
selected spacer between the output shaft bearing outerrace and the transaxle case.
(2) Set so that the threaded hole of the reverse idler gear
shaft’s head is facing in the direction indicated in the
illustration.
NOTEIf there is a great deviation in the direction in which the
threaded hole is facing, it will be impossible to align thethreaded hole and the hole in the case after the
transaxle case is installed.
(3) Apply specified sealant to the clutch housing side of thetransaxle case.
Specified sealant: MITSUBISHI GenuinePart
No.MD997740 or
equivalent
CautionB
Squeeze out sealant from the tube uniformly with- -
out excess or discontinuity.(4) Install the transaxle case onto the clutch housing.

21-34MANUAL TRANSAXLE - Transaxle Assembly
? ,‘,
30-35 Nm77-25 fLlbs.35-42 Nni26-30 ftlbs.
25
APi 77
--2lRl 26
\\15-22 Nm
---- -_ . .23
II-15 lt.lDS.
I
..d.. -Disassembly steps
23. Reverse idler gear shaft bolt24.Gasket
25.Bolt
l + 26. Transaxle case+4 ;I. ;$yrde
29:Springwasher30.Stopper bracket31. Restrict ball assembly
32.Gasketl 433.Oil seal34. Bearing outer racel * 35. Spacer
36. Bearing outer racel 437.Spacer38.Oil filter39. Bearing outer race32-39
ft.lbs.
TFMOlO9
l 4 40. Spacer41. Bearing outer race
I)* ;I. Sggcer
44: Reverse shift lever assembly
45. Reverse shift lever shoe
l + 46. Reverse idler gear shaft47. Reverse idler gear+e l + 48. Spring pinl * l + 49.Spring pin+I) l 50. Shift rail assembly
NOTE(I) Reverse the disassembly procedures to reassemble.(2) +e : Refer to “Service Points of Disassembly”.(3) e* : Refer to “Service Points of Reassembly”.(4) 19 : Non-reusable parts

_-MANUAL TRANSAXLE
- Transaxle Assembly 2%35
11-15 ftlbs.
5115-22 Nm
11-15
ftlbs.
l,451.Bolt
52.Bolt
53.Bearing retainer54.Intermediate gearassembly
55. Input shaft assembly
56. Output shaft assembly
57. Differential gear assembly
58. Bearing outer race
59. Bearing outer race60. Oil guide
61. Bearing outer race62. Bearing outer race
/’
62
+463.Oil seal+464.Oil seal
65.Magnet
66.Magnetholder67. Clutch housing assembly
; .,
FFkeverse the disassembly procedures to rdassembte.(2) ++ : Refer to “Service Points of Reassem’bly”.(3) m : Non-reusable parts

MANUAL TRANSAXLE - Transaxle Assemblv 21-37
18
50. REMOVAL OF SHIFT RAIL ASSEMBLY(1) Shift the
1st~2nd speed shift fork to the 2nd speed.
(2) Shift the
3rd4th speed shift fork to the 4th speed.
.”(3) Remove the shift rail assembly.
INSPECTIONNZlMOM
BACKUP LIGHT SWITCHOperate the backup light switch to check continuity with a
circuit tester.
If without continuity, replace the switch.
SERVICE POINTS OF REASSEMBLY64. INSTALLATION OF OIL SEAL
Install the drive shaft oil seal using the special tool.
:

21-38 MANUAL TRANSAXLE - Transaxle Assembly
63. INSTALLATION OF OIL SEALInstall the input shaft front oil seal using the special tool.
,,=
2010041
51. APPLICATION OF ADHESIVE TO BOLTApply specified adhesive to the bolt threads.
CautionDo not apply to the bolt head.
Specified adhesive: MOPAR Part No.4318031or MOPAR Part
No.4318032
or equivalent
50. INSTALLATION OF SHIFT RAIL ASSEMBLY
(1) Set the lst-2nd speed shift sleeve at 2nd speed.
(2) Set the
3rd-4th speed shift sleeve at 4th speed.
(3) FJtt~~~shift forks of shift rail assembly to groove of
(4)
Insert the shift rails into the shift rail holes of clutch
housing.(5) Turn the shift rails in the directions indicated by the
arrows in the order shown in the illustration, and
engage the shift lugs to control finger and interlock
plate.A