1991 MITSUBISHI ECLIPSE oil

17-16REAR SUSPENSION - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONSNl’ICA-B jG
ItemsSpecifications
Suspension systemDouble wishbone suspension type
Coil spring
Wire dia. x O.D.
x free lengthmm (in.)11.0 x 106.0 x 332.5 (.43 x 4.17 x 13.1)Coil spring identification colorPurple
x 1Spring constantN/mm
(Ibs./in.) 25.0 (140)
Shock absorber
TypeHydraulic, cylindrical, double-acting type
Max. lengthmm (in.) 568
(22.4)Min. lengthmm (in.) 380
(15.0)
Strokemm (in.) 188 (7.4)
Damping force [at 0.3 m/set. (0.9
ft./set.)]
ExpansionN (Ibs.) 900 (198)
ContractionN (Ibs.) 300 (66)
SERVICE SPECIFICATIONS
Items
Standard value
Toe-in
CamberSpecificationsmm (in.) 3.6+3 (.14f.l18)
-1"33'f30'
Nl7CEB
:&

REAR SUSPENSION - Shock Absorber Assemblv
DISASSEMBLY AND REASSEMBLY
Nl’IGM-Bnut Piston rod tightening
Washer
Upper bushing
(A)Bracket assembly
Spring pad
Upper bushing
(8)CollarCup assembly
Dust cover
Bump rubber
Coil spring
Shock absorber
20-25 Nm1210360
SERVICE POINTS OF DISASSEMBLYN17GNAA22. REMOVAL OF PISTON ROD TIGHTENING NUT
(1) Before removing the piston rod tightening nut com-
press the coil spring using the special tools.
Caution
Do not use an air tool to tighten the bolt of the
special tool.
(2) While holding the piston rod, remove the piston rod
tightening nut.
INSPECTIONN17GOAA2l Check the rubber parts for damage.
l
Check the coil springs for crack, damage or deterioration.

17-34REAR SUSPENSION - Shock Absorber Assembly
12A0049CUP assemblv
Dud cover
Bracket assembly
1Shock absorber lower bushing
12R0140I
SERVICE POINTS OF REASSEMBLY; N17GPi4te12. INSTALLATION OF COIL SPRING
(1) Use the special tools (L-4514) to compress the coi! zspring and insert it in the shock absorber.
(2) Align the edge of the coil spring to the position of the
shock absorber spring seat as shown.
10. INSTALLATION OF DUST COVER/S. CUP ASSEMBLY
As shown in the illustration, fit the dust cover to the cup
assembly.5. INSTALLATION OF BRACKET ASSEMBLY/Z. PISTON
ROD TIGHTENING NUT
(1) With the position of the bracket assembly as shown in
the figure, tighten the tightening nut to the specified
.%
torque.
-(2) Install the coil spring so that the lower edge fits into the
spring seat groove and the upper edge fits into the
spring pad groove, then remove the special tools
(L-4514).

STEERING
CONTENTSNISAA-
MANUAL STEERINGGEAR BOX.................21
POWER STEERINGGEAR BOX...................
28
POWER STEERING
HOSES........................
46
POWER STEERING OIL PUMP....................39
SERVICE ADJUSTMENT PROCEDURES >...........................7
Steering Angle Check..............................7
Steering Wheel Centering.........................8
Steering Wheel Free Play Check.............:..7Tie Rod End Ball Joint Starting Torque
Check..................................................8Tie Rod End Ball Joint Variation Check
(Shaft direction).....................................7
SERVICE ADJUSTMENT PROCEDURES
< POWER STEERING >.............................
10
Bleeding...............................................13Fluid Level Check...................................
12
Fluid Replacement..................................12
i;,
Oil Pressure Switch Check........................15
Oil Pump Pressure Test...........................14
Stationary Steering Effort Check.................11Steering Angle Check..............................
10
Steering Wheel Centering.........................1 1
Steering Wheel Free Play Check................10Steering Wheel Return to Center Check.......
11Tie Rod End Ball Joint Starting Torque
Check..................................................10Tie Rod End Bail Joint Variation Check
(Shaft direction).....................................10
V-Belt Tension Check..............................12
SPECIAL TOOLS......................................6
SPECIFICATIONS.....................................2;
General Specifications..............................2
Lubricants.............................................5
Sealants and Adhesives............................5
Service Specifications.............‘................2
Torque Specifications,. . . . . . . . . . . . . . . . . ..*..........3
STEERING WHEEL AND SHAFT.................. 16

19-2STEERING - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
ItemsSteering wheel
Steering wheel O.D.mm (in.)
Gear boxSteering gear type
Power steering oil pump
Oil pump type
Displacementcm3/rev. (cu.in./rev.)
Relief set pressureMPa (psi)
SERVICE SPECIFICATIONS
MANUAL STEERING
Items
Standard value
Steering angleInner wheel
Outer wheel
Tie rod end ball joint starting torqueNm
(in.lbs.)Assembly dimension of lower column tubemm (in.)
Total pinion torqueNm
(in.lbs.)From
O-90”From
90”-650”Tie-rod joint swing resistance
N (Ibs.)Tie-rod joint swing torque
Nm
(in.lbs.)
LimitSteering wheel free play
mm (in.)
Variation of tie rod end ball joint shaft directionmm (in.)
POWER STEERING
Items
Standard valueSteering wheel free play (with engine stopped)
mm (in.
Steering angle
Turbo
Inner wheel
Outer wheel
Other models
Inner wheel
Outer wheel
Tie rod end ball joint starting torque
Nm
(in.lbs.)Stationary steering effort
N (Ibs.)Assembly dimension of lower column tube
mm (in.)
V-belt deflection
mm (in.)
NlSCA--
Specifications372 (14.6)
Rack and pinion
Vane type
9.6 t.59)
8 (1,138)NlSCB-
Specifications37000’
* 20
3OOOO’
0.5-2.5 (4-22)
24.8-25.2
(.98-,991
0.6-l .3 (5-l 1 I
0.2-l .o (2-9)
8-20 (I .8-4.4)2-5
(17-43)30 (1.2)
1.5 l.059)
Specifications
11
(.43)
31"30'+2"
27"OO'
35"00'f2"
29"20'
0.5-2.5 (4-22)
37 (8) or less
24.8-25.2
(.98-.99)6-9 (.24-.35)

-
STEERING - Specificdions
i’.g=s
“,.
itemsSpecifications
Oil pump pressure
MPa (psi.)
Pressure gauge valve closed7.5-8.2 (1,067-1,166)
Pressure gauge valve opened0.8-I .O (114-142)
Oil pressure switch operating pressure
MPa (psi1Oil pressure switch contacts closed (continuity)
1.5-2.0 (213-284)Oil pressure switch contacts opened (no continuity)
0.7-1.2 (100-171)Total pinion torque
Nm
(in.lbs.)0.6-I .3 (5-l 1)Tie-rod joint swing resistance
N (Ibs.18-20 (1.9-4.6)Tie-rod joint swing torque
Nm
(in.lbs. 12-5 (17-43)
LimitSteering wheel free play (when hydraulic operation)
30
(1.2)mm (in.)Variation of tie rod end ball joint shaft direction
mm
(in.) 1.5 (.059)
Oil pump pressure
Pressure gauge valve openedMPa (psi)1.5 (213)Space between vane and rotor
mm
(in.)0.06 i.0024)Shaft backlash of pump body bushing and pulley assembly
0.1
i.004)mm (in.)
TORQUE SPECIFICATIONSNlSCC--
c.ItemsSteering wheel and shaft
Steering wheel lock nut
Lower bracket
Tilt bracket installation bolt
Joint assembly
Column support
Column tube clamp
Manual steering gear box
Joint assembly to gear box
Tie rod end to knuckle
Stay to crossmember
Stabilizer bar bracket
Front roll stopper insulator nut
Center member to body
Front exhaust pipe to rubber hanger
Front exhaust pipe mounting bolt
Front exhaust pipe mounting nut
Gear box mounting bracket to crossmember
Tie rod end lock nut
Tie rod to rack
Rack support cover locking nut
Top plug locking nutNmftlbs.35-45
25-33
8-12
6-9
8-12
6-9
15-2011-148-12
6-9
4-5
3-4
15-20 a11-1424-34
17-25
70-8051-58
30-4222-30
50-6536-47
80-l 0058-72
IO-157-l 1
30-4022-29
30-4022-29
60-8043-58
50-5536-40
80-10058-72
50-7036-51
50-7036-51

19-4STEERING - Specifications
ItemsNmIft.lbs.Power steering gear box
Joint assembly
Pressure hose to gear box
Return tube to gear box
Tie rod end to knuckle
Stay to crossmember
Stabilizer bar bracket
Front roll stopper insulator nut
Centermember to body
Front exhaust pipe to rubber hanger
Front exhaust pipe mounting bolt
Front exhaust pipe mounting nut
Gear box mounting bracket to crossmember
Tie rod end lock nut
Tie rod to rack
Feed tubes
End plugPinion and valve assembly to self-locking nut
Rack support cover locking nut
Valve housing installation bolts
Power steering oil pump
Pressure hose to oil pump
Oil pump to oil pump bracket
Heat protector installation nut
Oil pump bracket to engine
1.8L Engine
Front side
Left side2.0L DOHC Engine
Oil reservoir installation bolt
Oil reservoir bracket installation bolt
Pump cover to pump body
Suction connector to pump body
Connector to pump body
Terminal assembly to pump body
ower steering hoses
Cooler tube to body
Cooler tube to hood lock stay
Cooler tube clamp
Return tube to body
Pressure tube to gear box
Return tube to gear box
Pressure hose to body
Pressure hose to oil pump
Pressure hose to pressure tube
Pressure hose bracket11-14
9-13
9-13
17-25
51-58
22-3036-47
58-72
7-11
22-29
22-29
43-58
36-4058-72
9-13
36-51
14-22
36-51
12-19
15-2012-18
12-18
24-34
70-80
30-42
50-65
80-100
10-15
30-40
30-40
60-80
50-55
80-10012-18
50-70
20-30
50-7017-26
14-21
10-1535-45
25-33
9-14
7-1027-41
20-3025-33
18-24
25-33
18-24
9-14
7-109-14
7-1018-22
13-16
6-104-7
50-7036-51
25-3018-22
9-14
7-104-6
29-43
3.0-4.5'2-3
9-14
7-1012-18
9-13
12-18
9-13
9-14
7-1014-21
IO-15
30-4022-29
9-14
7-10

STEERING - Smcifications
LUBRICANTS_’” I_: Nls%D--
ItemsSpecified lubricantQuantity
The sliding part of the
bearing
The surfaces of the
bearing spacer
The mating surfaces of
the joint and cover
assembliesMOPAR Multi-mileage Lubricant Part No. 2525035 orequivalentAs required~ 8’i-.A
, ” ‘i
Manualsteeringgear boxBellows
The toothed surface of
the rack and to the inner
side of the rack bushing
The toothed surface of
the pinion
The surface of the racksupport that contacts
Inner side of the racksupport spring
Tie rod end dust coverSilicone grease
MOPAR Multi-mileage Lubricant Part No. 2525035 or
equivalent
As required
Power
steering
gear boxBellows
Bearing
O-ring
Oil seal
Special tool (MB991 213)
Pinion and valve
assembly seal ring partSilicone grease
MOPAR ATF PLUS (Automatic Transmission Fluid Type
7176VAutomatic transmission fluid “DEXRON” or
“DEXRON II”
As required
Coating of the rack teethMOPAR Multi-mileage Lubricant Part No. 2525035 or
face
equivalent
Pinion and valve
assembly pinion gear part
Rack support surface in
contact with the rack bar
Tie rod end dust cover.I
PowerPower steering fluidMOPAR ATF PLUS (Automatic Transmission Fluid Type0.9 liter (.95 qt.)
steering oil7176)/Automatic transmission fluid “DEXRON” or
pump“DEXRON II”
Flow control valveMOPAR ATF PLUS (Automatic Transmission Fluid TypeAs requiredFriction surface of rotor,7176)/Automatic transmission fluid “DEXRON” or
vane, cam ring and pump“DEXRON II”
cover
O-ring
SEALANTS AND ADHESIVESNWCE--
,.IItems
Manual steeringgear boxTop plug screw
Rack support coverDust cover
Specified sealant and adhesive
3M ATD Part No. 8663 or equivalentPower steering
gear boxEnd plug screwPower steering rack support cover screwDust cover
3M ATD Part No. 8663 or equivalent