1991 MITSUBISHI 3000GT brake

00-44
GENERAL - Main Sealant and Adhesive Table
MAIN SEALANT AND ADHESIVE TABLEMWZA- -
ApplicationRecommendedbrand
1. Sealants for engine accessories
(I 1Sealing between rocker
3M ATDcover and camshaft
Part No. 8660
bearing cap
(4G6 DOHC and 6G7or equivalent
engines only)
(2) l Sealing between semi-3M ATD
circular packing and
Part No. 8660
rocker cover and between
semi-circular packing andor equivalent
cylinder head
l Oil pressure switch
(except 4Gl and 6G7engines)
(3) Engine coolanttemperature switch,Engine coolanttemperature sensor,Therm0 valve,Therm0 switch, Joints,Engine coolanttemperature gauge unit(large size)
3M Nut LockingPart No. 4171
or equivalent
(4) Engine coolanttemperature gauge unit(;.s;il size, MD091 0563M ATDPart No. 8660
or equivalent
(5) Oil pan(except 4G5 engine)MITSUBISHI
GENUINE Part No.
MD9971 10or equivalent
2. Sealing between glass and
weatherstrip
(I 1 l Sealing between
tempered glass and
weatherstrip
l Sealing between body
flange and weatherstrip3M ATD
Part No. 8513or equivalent
3M ATD
Part No. 8509or equivalent
(2) Sealing betweenlaminated glass andweatherstrip
3. Adhesion with ribbon sealer
l Waterproof film for doorl Fender panell Splash shieldl Mudguardl Rear combination lamp
3M ATDPart No. 8509
or equivalent
3M ATDPart No. 8625or equivalent
ApplicationRecommended
brand
4. Adhesives for interior trim
(1)Adhesion of polyvinyl-chloride sheet3M Part No.EC-l 368or equivalent
(2)Adhesion of door
3M ATD
weatherstrip to body
Part No. 8001 or3M ATDPart No. 8011or equivalent
(3) Sealing betweengrommet or packing and
metal seal
(4) l Adhesion of headliningand other interior trimmaterialsl Adhesion of fuel tank
to pad
3M ATDPart No.851 3or equivalent3M
Part-No.
EC-l 368
or 3M ATD Part No.
8080 or equivalent
5. Body sealant3M ATDl Sealing of sheet metal,
Part No. 8531 or
drip rail, floor, body side3M ATDpanel, trunk, front panel and
Part No.8646the like jointsl Sealing of tailgate hingesor equivalent
6. Chassis sealant
(I 1 l Sealing of flange surfaces3M ATD
and threaded portions
Part No. 8659l Fuel gauge unit packingor equivalent
(2)Sealing of flange surfaces,3M ATD
threaded portions, packingPart No.8663
and dust cover
l Differential carrier packingor equivalent
l Dust covers for ball jointand linkage
l Steering gear box packing
and shims
l Steering gear housingrack support cover andtop coverl Mating surface of knucklearm flange
(3)Sealing between accelerator
arm bracket and toeboardDrying sealant
(4)Sealant for drum brakeshoe hold-down pin andwheel cylinder3M ATDPart No.851 3or equivalent
TSB Revision1

ENGINE - Engine AssemblyII-17
ENGINE ASSEMBLY
/REMOVAL AND INSTALLATION
I
Pre-removal Operationl Release of Residual Pressure from HighPressure Fuel Hose(Refer to GROUP 13 -Service AdjustmentProcedures,)l Removal of Cruise Control Pump andLink Assembly(Refer to GROUP 13 - Cruise Control.)l Removal of Hood(RefertoGROUP42A-Hood.)
l
Removal of Air Hose and Air Pipe (Refer to GROUP 15 - Inter Cooler.)l Removal of Front Exhaust Pipe(Refer to GROUP 15 - Exhaust Pipe and Main Muffler.l Removal of Transaxle Assembly(Refer to GROUP 22, 23 -Transaxle Assembly.)l Removal of Radiator(Refer to GROUP 14-Radiator.)
Post-installation Operationl Installation of Radiator(Refer to GROUP 14 - Radiator.)l Installation of Cruise Control Pump andLink Assembly(Refer to GROUP 13 -Cruise Control.)l Installation of Transaxle Assembly(Refer to GROUP 22,23 -Transaxle Assembly.)l lnstallatron of Front Exhaust Pipe(Refer to GROUP 15 - Exhaust Pipe and Main Muffler.)l Installation of Air Hose and Air Pipe (Refer to GROUP 14 - Inter Cooler.)l Installation of Hood(Refer to GROUP 42A- Hood.)l Supplying of Engine Oil(Refer to GROUP 00 - Maintenance Service.)l Adjustment of the Accelerator Cable(Refer to GROUP 13 - Engine Control.)
MllSA-B
4 ft.lbs.
6
40-45 Nm
29 - 33 fklbs.
Removal steps
1. Connection of accelerator cable11. Drive belt (Alternator and air conditioner)
2. Connection of brake booster vacuum hose(Refer to P.l l-l 1.)
3. Connection of booster vacuum12. Drive belt (Power steering)
hose
(Referto P.l l-l I.)4. Connection of fuel return hose13. Connection of alternator harness
5. Connection of fuel high pressure hose14. Oxygen sensor connector
6. Connection of ground cablel *15. Air conditioner compressor
7. Solenoid valve assembly4w
16. Power steering oil pump
8. Connection of vapor hose17. Oil pressure switch connector (Power steer-9. Connection of heater hoseing)10. EGR temperature sensor connector18. Connection of oil cooler pipes

OlFOO43
TSB Revision1

11-26ENGINE - Timing Belt
TIMING BELT
REMOVAL AND INSTALLATION
MllKA-BI
Pre-removal Operationl Removal of the Under Cover (Front L.H.,side L.H.)l Removal of Front Under Cover Panel(Refer to GROUP 51 -Aero Parts,)l Removal of Cruise Control Pump andLink Assembly(Refer to GROUP 13 -Cruise Control.)l Removal of Alternator Assembly(Referto GROUP 16-Alternator.)
l Raise and Suspend the Engine to the ExtentForce is not Applied to the Engine Mounti LIOO-
120 Nm72 - 87 ft.lbs.
35 Nm25 ft.l$.
TurbochargerOSFOO03
lo-12Nm7 - 9 ft.lbs.
Removal steps
1. Air hose
11 31 ftlbs.
‘5IO-12Nm
B;p 49ftJbs.
\
180- 190 Nm130 - 137 ft.lbs.
2. Air pipe
3. Tensioner assembly
4. Drive belt (power steering)
(RefertoP.ll-11.)4** I)* 5. Crankshaft pulley’6. Brake fluid level sensor
7. Timing belt upper cover
8. Engine mount bracket
9. Idler pulley (alternator
/ air conditioner)+* l * 10. Engine support bracketl * 11. Timing belt lower coverl * lAdjustment of timing belt tensionl * l a 12. Timing beltl * 13. Auto tensionerNm
[email protected].
Post-installation Operation
l Installation of Alternator Assembly(Refer to GROUP 16 -Alternator.)
l Installation of the Under Cover(Front L.H., Side L.H.)l Installation of Front Under Cover Panel
l Installation of Cruise Control Actuator(Refer to GROUP 13 - Cruise Control.)l Adjustment of theEngine (Refer to P.l l-1 1.)n7 m-m
M D998754nSERVICE POINTS OF REMOVAL
5. REMOVAL OF CRANKSHAFT PULLEYMllKBEF
,Using special tools, remove the crankshaft pulley from the
crankshaft.
TSB RevisionII
CautionUse only the specified special tools, or a damaged
pulley damper could result.
,
LJ

FUEL
SYSTEM
CONTENTSM13AA- _
CRUISE CONTROL SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . .158SPECIFICATIONS. . . . . . . .._._....................................................155
CRUISE CONTROL SYSTEM*................................................185
SERVICE ADJUSTMENT PROCEDURES............................178
Cruise Control Cables Inspection and Adjustment........178Cruise Control SystemInspection....................................179individual Parts Inspection....................................................181
SPECIAL TOOLS........................................................................159
SPECIFICATIONS....................................................................158
General Specifications........................................................158Service Specifications........................................................158
TROUBLESHOOTING............................................................159
Check Chart............................................................................163Harness and Components Layout....................................176Preliminary Inspection........................................................159Self-diagnosis Checking........................................................172Troubleshooting Quick Reference Chart............................159
ENGINE CONTROL............................................155
ENGINE CONTROL................................................................157
SERVICE ADJUSTMENT PROCEDURES............................156
Accelerator Cable Inspection and Adjustment................156Accelerator Switch Inspection and Adjustment................156
Service Specifications........................................................
155
TROUBLESHOOTING............................................................
155
Accelerator Cable and Accelerator Pedal........................155
FUEL SYSTEM....................................................3
DETONATION SENSOR........................................................154
FUEL FILTER............................................................................
153
FUEL LINE AND VAPOR LINE................................................151
FUEL PUMP AND FUEL GAUGE UNIT ASSEMBLYAND OVERFILL LIMITER (TWO-WAY VALVE)................149
FUEL TANK.................................................................................146
GENERAL INFORMATION
....................................................
3
MPI System Diagram............................................................3
INJECTOR................................................................................141
ON-VEHICLE INSPECTION OF MPI COMPONENTS........36
Active Exhaust Control Unit ............................130Air Conditioner Switch and Power Relay............................82Air Flow Sensor....................................................................54Anti-lock Brake Signal ........................................133Barometric Pressure Sensor................................................60CONTINUED ON NEXT PAGE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP
528 -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

FUEL SYSTEM - On-vehicle InsDection of MPI ComDonents
/
idHARNESS INSPECTION
Engine control
unit harness
side connector7FUO689
side connector7FuO689
PU
Engine control
unit harness
side connectorT7FUO689
Measure the input voltage of engineIcontrol unit.
lEngine control unit connector:
Disconnectedl Lighting switch: ON
(Tail light relay ON)
Measure the input voltage of enginecontrol unit.
lEngine control unit connector:
Disconnectedl Defogger switch: ON
(Defogger relay ON)Voltage
(V)
Isv
cl3
Check circuit
related to de-
fogger relay
Measure the input voltage of enginecontrol unit.
lEngine control unit connector:
Disconnected
l Brake pedal: Depressed(Stop light switch ON)
Check circuitTSB Revision

FUEL SYSTEM - On-vehicle .lnspection of MPI Components13-111
INSPECTIONUsing Multi-use Tester
FunctionItem No. Data display
Data reading 45
Stepper
1
motor steps
~
Check condition
l Engine coolant tem-
perature: 80 to 95°C
(176 to 205°F)
0 Lamps, electric cooling
fan, accessory units:
All OFFl Transaxle: Neutral(P range for vehiclewith AA>l Steering wheel: Neutrall Idle position switch: ON(compressor clutch
to be ON if air condi-
tioner switch is ON)l Engine: idling
Load stateStandard value
;;rnditioner switch:2 - 12 stp&conditioner switch:
25 - 65 stp
l $irNconditioner switch:15 - 63 stp0 Selector lever:Shift to D range
NOTEWhen the vehicle is new [within initial operation of about 500 km (300 miles)], the stepper motor steps may be about 30steps more than standard.
CautionWhen the selector lever is shifted to the “D”range, the brakes must be used to prevent the vehicle frommovingforward.
03A020
Using Oscilloscope(1) Connect the probe to each oscilloscope pick-up point as
shown in the circuit diagram.
(2) Start the engine.
(3) When the air conditioner switch is turned on, the idling
speed increases to operate the idle speed control. Check
the instantaneous waveform.
NOTEKeep in mind that the waveform can be observed only
when idle speed control is in operation.
1 TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components
ANTI-LOCK BRAKE SIGNAL
Engine control
unit connectorABS ECU@ ABS control unit
equipment side connector
A28
tABS HU
Engine
control
unit
114
/L6FU1542
7FUO653,
OPERATIONlThe anti-lock brake signal is input to the engine control unit from the anti-lock brake system
(ABS) control
unit as a signal to indicate whether or not the motor relay is activated. Based on this signal, the engine
control unit controls the idle-speed control servo to secure effective anti-lock braking.
lWhen the motor relay is activated, the ABS control unit turns ON the power transistor, short-circuiting the
terminal to ground. This causes the anti-lock brake signal to go from high to low.
TSB Revision

CRUISE CONTROL SYSTEM - Troubleshootina13461
Trouble symptom
l The set vehicle speed variesgreatly upward or downward.l “Hunching” (repeated alter-
nating acceleration and
deceleration) occurs after
setting is made.
Probable cause
Check chart No.Remedy
Malfunction of the vehicleNo. 4Repair the vehicle speedspeed sensor circuit
sensor system, or replacethe part.Malfunction of thespeedometer cable orspeedometer drive gear
Vacuum pump assembly
No. 5Repair the actuatorcircuit poor contact
system, or replace thepart.Malfunction of thevacuum pump assembly
(including air leaks from
negative pressure
passage)
The cruise control system is notcanceled when the brake pedal
is depressed.Malfunction of the ECU
-Replace the ECU.
Brake switch (for cruiseNo. 6Repair the harness or
control) malfunction
replace the stop light
(short-circuit)switch.
Vacuum pump assemblyNo. 5Repair the harness ordrive circuit short-circuitreplace the vacuum pump
assembly.
The cruise control system is notcanceled when the clutch pedalis depressed. (It is canceled, however, whenthe brake pedal is depressed.)Malfunction of the ECU
-Replace the ECU.
Damaged or disconnected
If the input checkRepair the harness, orwiring of clutch switchcode No. 26 indicatesrepair or replace the clutch
input circuita malfunction.switch.No. 7Clutch switch improper
installation (won’t switch
ON)
Malfunction of the ECU-Replace the ECU.
The cruise control system is notDamaged or disconnectedIf the input checkRepair the harness, or
canceled when the shift lever iswiring of inhibitor switchcode No. 26 indicatesrepair or replace themoved to the “N” position.
input circuita malfunction.inhibitor switch.
(It is canceled, however, when
No. 8
the brake pedal is depressed.)Improper adjustment of
inhibitor switch
Cannot decelerate by using the
SET switch.Malfunction of the ECU
Temporary damaged ordisconnected wiring of
control switch input
circuit
-
No. 2Replace the ECU.
Repair the harness orreplace the control switch
Vacuum pump assemblyNo. 5Repair the harness orcircuit poor contactreplace the vacuum puml:assembly.
Malfunction of thevacuum pump assembly
Malfunction of the ECU
-Replace the ECU.
NOTEECU: Electronic control unit
1 TSB Revision