1991 MITSUBISHI 3000GT Rear wiper

EXTERIOR - Rear Wber and Washer51-35
REAR WIPER AND WASHERM51 KKAO
,/REMOVAL AND INSTALLATION
16FO104.lO
.llRemoval steps of wiper motor
1. Wiper blade
l *2. Wiper arm
3. SpacerRemoval steps of washer tube
Front pillar trim
(RH)Quarter trim (RH)
Liftgate lower trim (Refer to GROUP 52A -Quarter upper trim
(RH)Rear roof rail trim!R$$f$$ GRoUP 52A
Trims.)Rear side trim
(RH)i .
4. Wiper motor
l *8. Liftgate moulding, upper
9. Washer nozzle
Removal steps of washer tank
Rear end trim (Refer to GROUP
52A-Trims.)5. Cap
6. Washer tank
7. Washer motor
10. Tube and grommet assembly
11. Washer tube
1 TSB Revision

51-36EXTERIOR - Rear Wiper and Washer
nspection of operation16N0029
Inspection of stop position
16FO19116FO201SERVICE POINT OF REMOVAL
8. REMOVAL OF LIFTGATE MOULDING, UPPER
Using a special tool, pry the clip portion to remove the
’~
upper liftgate moulding.
INSPECTION
WIPER MOTOR
Check the wiper motor with it mounted on the vehicle and with
its harness connector disconnected.
Operation of Wiper Motor
Connect a battery to the wiper motor, as shown, to check the
operation of the wiper motor.
Wiper Motor Stop Position
(1) Operate the wiper motor by the procedure described above
and intermediately disconnect the battery to let the wiper
motor stop.
(2) Reconnect the battery as shown and check that the wiper
motor stops at the automatically-stopped position after
operation.
‘dWIPER WASHER SWITCH
(I) Remove switch garnish B from the knee protector.
(2) Operate the switch to check for continuity between the
terminals.
NOTEO-0 denotes that there is continuity between the terminals.
1 TSB Revision

EXTERIOR - Rear Wiper and Washer
51-3718N007F
jINTERMITTENT WIPER RELAY
(1) Remove the quarter trim. (Refer to GROUP 52A
- Trims.)
(2) With the intermittent wiper relay connected to the wiring
harness connector, let the wiper operate intermittently and
check the voltage at terminal
0.WASHER MOTOR
(1) When the washer motor is inspected, make sure that it is
mounted on the washer tank and that the washer tank is
filled with water.
(2) Connect the battery as shown to check whether water is
pumped out.
SERVICE POINT OF INSTALLATION
2. INSTALLATION OF WIPER ARM
After assembling the wiper blade to the wiper arm, install
the wiper arm with its tip positioned along the ceramic part.
TSB Revision

55-I 8HEATERS AND MANUAL AIR CONDlTlONER - Heater Control Assembly
HEATER CONTROL ASSEMBLY
REMOVAL AND INSTALLATIONM55GA-A
Pre-removal and Post-installation Operationl Removal and installation of Floor Console
(Refer to GROUP 52A- Floor Console.)
Removal steps
1. Stopper2. Glove box outer case assembly**3. Connection of the air-selection control wire
4. Ho01 lock release handle
5. Rheostat assembly
6. Rear wiper &washer switch
7. Knee protector
8. Shower duct
l *9. Connection of the mode control wirel * 10. Connection of the temperature control wirea*11. Center air outlet assembly
12. Heater control assembly
2OFOO78
III’ ’2OFOO3
ii,
I
I
I
I
I
‘d i
-
SERVICE POINT OF REMOVALM55GBAMl
11. REMOVAL OF CENTER AIR OUTLET ASSEMBLYDisengaging the clips (2 positions) of the center air outlet
assembly with a flat tip screwdriver, remove the center air
outlet assembly with the trim stick.
TSB Revision

55-38Ventilators (Air Inlet
HEATERS AND MANUAL AIR CONDITIONER - and Air Outlet)
VENTILATORS (AIR INLET AND AIR OUTLET)M55YD. -
REMOVAL AND INSTALLATIONinlet garnishes removal steps
1. Windshield wiper arm
2. Front deck garnish
3. Inlet garnish (right)
4. Inlet garnish (left)Rear ventilation duct removal steps
5. Rear ventilation duct A** l6. Side air dam (side sill)
(Refer to GROUP 51 - Aero Parts.)7. Rear ventilation duct B
:LI’
I
I
I
I
‘d ’
I
I
I
1 TSB RevisionI